* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Lab4 (wireless access point)
Survey
Document related concepts
Extensible Authentication Protocol wikipedia , lookup
Network tap wikipedia , lookup
Spectrum reallocation wikipedia , lookup
Airborne Networking wikipedia , lookup
Computer network wikipedia , lookup
Wake-on-LAN wikipedia , lookup
Wireless USB wikipedia , lookup
IEEE 802.11 wikipedia , lookup
List of wireless community networks by region wikipedia , lookup
Cracking of wireless networks wikipedia , lookup
Policies promoting wireless broadband in the United States wikipedia , lookup
Transcript
DKT 224 DATA COMMUNICATION & NETWORK LAB 4 WIRELESS ACCESS POINT Lab 4 Wireless Access Point 1. OBJECTIVE 1.1 To learn the configuration and setting-up Wireless Access Point 2. INTRODUCTION 2.1 WLAN WLAN provides all the benefits (and drawbacks) of the wired counterparts such as:i. Ethernet or ii. Token Ring without being limited to cabling restrictions. Before wireless we had to ensure that all cables were connected in some fashion. - With wireless LAN's, being connected no longer means that the network is attached by cables. Cabling distance limitations are increased from feet or meters to miles or kilometers. -With wireless the limitations of running wire through walls or under ground are no longer an issues. Making upgrades or additions to the network faster and easier. 2.2 Implications Wireless technology has several key benefits that can be applied to new networks and also to existing ones. ● Business owners that want to increase mobility within their areas without delays of running new cabling find that wireless increases their flexibility. Changes can be made in one area or throughout the entire site within a very short time. ● Some buildings make upgrades to networks almost impossible. Leased buildings or temporary locations make wiring a non-existant option. With wireless, the option to expand is brought back into play. Increasing the scalability and adaptability of the network. 2.3 How it Works WLANs use a transmission medium, just like wired LANs. Instead of using twisted-pair or fiberoptic cable, WLANs use either infrared (IR) light or RF. Of the two, RF is far more popular for its longer range, higher bandwidth, and wider coverage. Most wireless LANs today use the 2.4gigahertz (GHz) frequency band, the only portion of the RF spectrum reserved around the world for unlicensed devices. The freedom and flexibility of wireless networking can be applied both within buildings and between buildings. Wireless can be used to replace wired networks or to augment an existing wired network. The equipment that is used by wireless is similar to that of its wired counterpart and can be setup in the same fashion. Figure 1: A wireless peer-to-peer network Installing an access point can extend the range of a wired network, effectively doubling the range at which the devices can communicate. Since the access point is connected to the wired network each client would have access to server resources as well as to other clients. Each access point can accommodate many clients; the specific number depends on the number and nature of the transmissions involved. Many real-world applications exist where a single access point services from 15-50 client devices. Figure 2: Client and Access Point Access points have a finite range, on the order of 500 feet indoor and 1000 feet outdoors. In a very large facility such as a warehouse, or on a college campus it will probably be necessary to install more than one access point. Access point positioning is accomplished by means of a site survey. The goal is to blanket the coverage area with overlapping coverage cells so that clients might range throughout the area without ever losing network contact. The ability of clients to move seamlessly among a cluster of access points is called roaming. Access points hand the client off from one to another in a way that is invisible to the client, ensuring unbroken connectivity. Figure 3: Multiple access points and roaming To solve particular problems of topology, the network designer might choose to use Extension Points to augment the network of access points. Extension Points look and function like access points, but they are not tethered to the wired network as are APs. EPs function just as their name implies: they extend the range of the network by relaying signals from a client to an AP or another EP. EPs may be strung together in order to pass along messaging from an AP to far-flung clients, just as humans in a bucket brigade pass pails of water hand-to-hand from a water source to a fire. Figure 4: Use of an extension point One last item of wireless LAN equipment to consider is the directional antenna. Let’s suppose you had a wireless LAN in your building A and wanted to extend it to a leased building, B, one mile away. One solution might be to install a directional antenna on each building, each antenna targeting the other. The antenna on A is connected to your wired network via an access point. The antenna on B is similarly connected to an access point in that building, which enables wireless LAN connectivity in that facility. Figure 5: The use of directional antennas 2.3 History As we all know by now, Ethernet (IEEE 802.3) is the dominant LAN technology used today. Wireless technology, know by the Institute of Electrical and Electronics Engineers (IEEE) as the 802.11 standard. IEEE 802.11 was the first of the wireless LAN technologies and provided a data throughput of 1 - 2 Mbps and used a frequency range of about 900 Mhtz. Just as the 802.3 Ethernet standard allows for data transmission over twisted-pair and coaxial cable, the 802.11 WLAN standard allows for transmission over different media. Media (unbounded) include infrared light and two types of radio transmission within the unlicensed frequency band: frequency hopping spread spectrum (FHSS) and direct sequence spread spectrum (DSSS). Spread spectrum is a modulation technique developed in the 1940s that spreads a transmission signal over a broad band of radio frequencies. This technique is ideal due to being less susceptible to radio frequency interference. FHSS is limited to a 2-Mbps data transfer rate and is recommended for only very specific applications. For all other wireless LAN applications, DSSS is the better choice. The recently released evolution of the IEEE standard, 802.11b, provides for a full Ethernet-like data rate of 11 Mbps over DSSS with a frequency range of 2.4 Ghtz. FHSS does not support data rates greater than 2 Mbps. The current WLAN standard is IEEE 802.11a, which provides throughput of 54 Mbps and also uses DSSS on a frequency of 5 Ghz. Within the next year it is anticipated that the frequency will reach 5.7 Ghz and allow WLAN's to break the 100 Mbps threshold. 2.4 Throughput As with wired LAN systems, actual throughput in wireless LANs is product- and set-updependent. Factors that affect throughput include the number of users, propagation factors such as range and multipath, the type of wireless LAN system used, as well as the latency and bottlenecks on the wired portions of the LAN. Data rates for the most widespread commercial wireless LANs are in the 1.6 Mbps range. Users of traditional Ethernet or Token Ring LANs generally experience little difference in performance when using a wireless LAN. Wireless LANs provide throughput sufficient for the most common LAN-based office applications, including electronic mail exchange, access to shared peripherals, Internet access, and access to multi-user databases and applications. As a point of comparison, it is worth noting that state-of-the-art V.90 modems transmit and receive at optimal data rates of 56.6 Kbps. In terms of throughput, a wireless LAN operating at 1.6 Mbps is almost thirty times faster. 2.5 So why choose wireless? Pro's and Con's 2.5.1 Integrity and Reliability Wireless data technologies have been proven through more than fifty years of wireless application in both commercial and military systems. While radio interference can cause degradation in throughput, such interference is rare in the workplace. Robust designs of proven wireless LAN technology and the limited distance over which signals travel result in connections that are far more robust than cellular phone connections and provide data integrity performance equal to or better than wired networking. 2.5.2 Compatibility with the Existing Network Most wireless LANs provide for industry-standard interconnection with wired networks such as Ethernet or Token Ring. Wireless LAN nodes are supported by network operating systems in the same fashion as any other LAN node: thought the use of the appropriate drivers. Once installed, the network treats wireless nodes like any other network component. 2.5.3 Interoperability of Wireless Devices Customers should be aware that wireless LAN systems from different vendors might not be interoperable. For three reasons. First, different technologies will not interoperate. A system based on spread spectrum frequency hopping (FHSS) technology will not communicate with another based on spread spectrum direct sequence (DSSS) technology. Second, systems using different frequency bands will not interoperate even if they both employ the same technology. Third, systems from different vendors may not interoperate even if they both employ the same technology and the same frequency band, due to differences in implementation by each vendor. 2.5.4 Interference and Coexistence The unlicensed nature of radio-based wireless LANs means that other products that transmit energy in the same frequency spectrum can potentially provide some measure of interference to a wireless LAN system. Microwave ovens are a potential concern, but most wireless LAN manufacturers design their products to account for microwave interference. Another concern is the co-location of multiple wireless LANs. While wireless LANs from some manufacturers interfere with wireless LANs, others coexist without interference. This issue is best addressed directly with the appropriate vendors. 2.5.5 Licensing Issues In the United States, the Federal Communications Commission (FCC) governs radio transmissions, including those employed in wireless LANs. Other nations have corresponding regulatory agencies. Wireless LANs are typically designed to operate in portions of the radio spectrum where the FCC does not require the end-user to purchase license to use the airwaves. In the U.S. most wireless LANs broadcast over one of the ISM (Instrumentation, Scientific, and Medical) bands. These include 902-928 MHz, 2.4-2.483 GHz, 5.15-5.35 GHz, and 5.725-5.875 GHz. For wireless LANs to be sold in a particular country, the manufacturer of the wireless LAN must ensure its certification by the appropriate agency in that country. 2.5.6 Simplicity/Ease of Use Users need very little new information to take advantage of wireless LANs. Because the wireless nature of a wireless LAN is transparent to a user's NOS, applications work the same as they do on wired LANs. Wireless LAN products incorporate a variety of diagnostic tools to address issues associated with the wireless elements of the system; however, products are designed so that most users rarely need these tools. Wireless LANs simplify many of the installation and configuration issues that plague network managers. Since only the access points of wireless LANs require cabling, network managers are freed from pulling cables for wireless LAN end users. Lack of cabling also makes moves, adds, and changes trivial operations on wireless LANs. Finally, the portable nature of wireless LANs lets network managers preconfigure and troubleshoot entire networks before installing them at remote locations. Once configured, wireless LANs can be moved from place to place with little or no modification. 2.5.7 Security Security, as with all networks is a key concern. How do you protect a signal that is unbounded? The wired equivalent privacy (WEP) option to the 802.11 standard is only the first step in addressing customer security concerns. Security is currently available today for wireless networking, offering up to 128-bit encryption and supporting both the encryption and authentication options of the 802.11 standard. The algorithm with a 40- or 128-bit key is specified in the standard. When WEP is enabled, each station (clients and access points) has up to four keys. The keys are used to encrypt the data before it is transmitted through the air. If a station receives a packet that is not encrypted with the appropriate key, the packet will be discarded and never delivered to the host. Although the 802.11 standard provides strong encryption services to secure the WLAN, the means by which the secure keys are granted, revoked, and refreshed is still undefined. Fortunately, several key administration architectures are available for use in the enterprise. The best approach for large networks is centralized key management, which uses centralized encryption key servers. A popular strategy includes the addition of encryption key servers to ensure that valuable data is protected. Encryption key servers provide for centralized creation of keys, distribution of keys, and ongoing key rotation. Key servers enable the network administrator to command the creation of RSA public/private key pairs at the client level that are required for client authentication. The key server will also provide for the generation and distribution to clients and access points of the keys needed for packet encryption. This implementation eases administration and helps avoid compromising confidential keys. 2.5.8 Cost (US) A wireless LAN implementation includes both infrastructure costs, for the wireless access points, and user costs, for the wireless LAN adapters. Infrastructure costs depend primarily on the number of access points deployed; access points range in price from $1,000 to $2000. The number of access points typically depends on the required coverage region and/or the number and type of users to be serviced. The coverage area is proportional to the square of the product range. Wireless LAN adapters are required for standard computer platforms, and range in price from $300 to $1,000. The cost of installing and maintaining a wireless LAN generally is lower than the cost of installing and maintaining a traditional wired LAN, for two reasons. First, a wireless LAN eliminates the direct costs of cabling and the labor associated with installing and repairing it. Second, because wireless LANs simplify moves, adds, and changes, they reduce the indirect costs of user downtime and administrative overhead. 2.5.9 Scalability Wireless networks can be designed to be extremely simple or quite complex. Wireless networks can support large numbers of nodes and/or large physical areas by adding access points to boost or extend coverage. 2.5.10 Battery Life for Mobile Platforms End-user wireless products are designed to run off the AC or battery power from their host notebook or hand-held computer, since they have no direct wire connectivity of their own. wireless LAN vendors typically employ special design techniques to maximize the host computer's energy usage and battery life. 2.5.11 Safety The output power of wireless LAN systems is very low, much less than that of a hand-held cellular phone. Since radio waves fade rapidly over distance, very little exposure to RF energy is provided to those in the area of a wireless LAN system. Wireless LANs must meet stringent government and industry regulations for safety. No adverse health affects have ever been attributed to wireless LANs. 2.5.12 Summary Flexibility and mobility make wireless LANs both effective extensions and attractive alternatives to wired networks. Wireless LANs provide all the functionality of wired LANs, without the physical constraints of the wire itself. Wireless LAN configurations range from simple peer-topeer topologies to complex networks offering distributed data connectivity and roaming. Besides offering end-user mobility within a networked environment, wireless LANs enable portable networks, allowing LANs to move with the knowledgeable workers that use them. 3. PRACTICAL WORK Component and equipment Item 3.1 3.2 3.3 3.4 Details D-Link Wireless Router D-Link Wireless PCI Adapter Orinoco Wireless PCI Adapter PC Qty 1 1 1 3 4. PROJECT DETAILS In this lab session, students are required to set-up a Wireless Local Area Network (WLAN) consists of 3 PC’s by following the procedures as in 5. This project must be done in group. Upon the completion of your project, each group must present your WLAN to the lab instructor. 5. TASKS a. Configure and Setting-up D-Link Wireless Router SSID- Service Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN). Example Group ( 4 students/group) 1 2 3 4 5 6 7 SSID Mkq1_01 Mkq1_02 Mkq1_03 Mkq1_04 Mkq1_05 Mkq1_06 Mkq1_07 b. Configure and Setting-up D-Link Wireless PCI Adapter Reference: User Manual Configure and Setting-up Orinoco Wireless PCI Adapter Reference: User Manual c. Setting up IP – IP Address For each PC d. Setting up Security - 128-bit encryption e. Testing and verify connection using ping command. Upon the completion of your project, i. Each group must present your LAN to the lab instructor. ii. Lab Discussion:Write down a simple and brief discussion of what you have learnt from this lab session. Complete all the tasks in the given project. Submit your report to your lecturer. Do not copy other students work. Make your own report. Extra Question. 1. WLAN provides all the benefits (and drawbacks) of the wired counterparts such as:i. Ethernet or ii. Token Ring without being limited to cabling restrictions. Comparing both Ethernet and Token Ring, discuss the benefits and drawbacks of each LAN. If you are given a choice to setup a network for your company which one will you choose? Why?