* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Welcome to Ebenezer’s Sound Tech Training I’m sure this thing worked last Sunday The Importance of Acoustics What did he say? The Effects of Too Much REVERBERATION • • • • Impacts spoken word more than music. Impacts those with hearing loss the most. Makes certain words difficult to understand. Causes listener fatigue. How To Control REVERBERATION • Use construction techniques which minimize reflections. • Aim speakers to focus sound away from ceiling and walls. • Use equalization to reduce frequencies which naturally resonate in the room. As A Sound Tech,Your Biggest Mistake is Adding Too Much Bass Or having stage monitor levels set too high The congregation needs to listen to the main speakers, not the monitors! Always Check out the system before the service…. • • • • • • Mixer controls set normal. Mikes connected and working. Instruments connected and working. Monitor speakers aimed correctly. Wireless batteries in good condition. Service tape loaded and ready to go. Two minutes prior to start of service is NOT the ideal time to begin a trouble-shooting process! Mark POWERING UP THE SYSTEM ON FIRST OFF FIRST Avoid damaging “POPS” - always turn power on or off in the order indicated! NEVER CONNECT OR DISCONNECT MICROPHONES OR INSTRUMENTS…. Unless the channels are muted or the system is off. Pops, clicks, and buzzes can damage speakers! Always use the right cable! Small round shielded cable for instruments Large flat unshielded cable for speakers Examining Signal Flow It All Starts Here… DI Box Mixer The Big Picture Peavey From Signal Sources AUX-2 70 Volt Amp Fold-back Speaker 70 Volt Amp Class Speakers Bogen MAIN AUX-1 Mackie EQ CONTROLLER Peavey Tannoy Main Speakers Tannoy EQ Monitor Speakers Peavey Yamaha Peavey Class Speakers actually consist of... • • • • • Two speakers in the Narthex. A speaker in the nursery. A speaker in each of the young kids rooms. A speaker in the kitchen. Each room has its own volume control located in the room. DON’T MESS WITH THE GRAPHIC EQUALIZERS! You can cause real problems with the system. Setting them requires the proper test equipment! The Mackie SR24-4 Mixing Console TWO IMPORTANT SWITCHES Master Power Phantom Power Both must be on at all times! Mixer Rear Panel, lower left corner What is Phantom Power? • Low voltage applied to the mike lines by the mixer. • Used to power electret mikes and active direct boxes. • If the switch is off, choir mikes, podium mike and Peavey direct boxes will be dead. The Mono Channel Strip Learn one and you know all twenty. Signal Flow Top to Bottom The TRIM control • The first stop for the signal at the mixer. • Sets the overall level of the signal going to the rest of the mixer circuitry. • Compensates for differing levels of various input devices. • Proper setting is essential to low noise and ample “head room”. TRIM Control Warning! TURN DOWN THAT TRIM! If the red OL light comes on then your trim control is set too high! What is ample HEAD ROOM? No, its not having enough rest rooms on a ship! Clip Signal Level Head Room Normal Noise Time Clipping Causes Distortion….. Clipping Signal Level Clip Normal Noise Time …..and distortion can blow your speakers! Yikes! Hard Feedback Can Toast your speakers too If you go “ouch” after that last squeal, chances are so did your speakers! and so can pops, clicks, and buzzes caused by plugging/unplugging hot mikes or instruments! Always mute the channel at the mixer first! Ways to set the TRIM Control The Traditional Way…. TRIM? Back down from clipping and hope for the best. Or….. The MACKIE Way sets the gain structure accurately by using the VU meter lights • Channel SOLO button down. • SOLO MODE in Pre-fade (Up). • Adjust TRIM for zero on the VU Meter. The AUX 1 Control • Controls how much channel signal is sent to the stage monitor speakers. • Always Pre-Fade, which means it is …. • not affected by the channel EQ. • not affected by the PAN control. • not affected by the channel fader. • affected by the MUTE control. AUX 1 (Monitor) Rule Never mix choir mikes into the stage monitors! Feedback will be too difficult to control. I wish I hadn’t done that! The AUX 2 Control • Controls how much channel signal is sent to the stage fold-back speaker. • Like AUX 1, it is always Pre-Fade. • Used to send voice to the front edge of the stage. • Speaker does not have the frequency range to handle music. The AUX 3 Control You get a break - we don’t use it! The AUX 4 Control • Controls how much channel signal is sent to the CD/TAPE machine for recording. • Used in post-fade mode (PRE button up) so that the signal…. • Is controlled by the channel fader. • Is processed by the channel EQ. • Is affected by the PAN control. • Is affected by the MUTE control. . Please make sure the PRE button is out. This places AUX 3 and AUX 4 in the post-fader mode. The AUX 5 Control • Controls how much channel signal is sent to the SERVICE TAPE MACHINE. • Always post-fader. Today’s Sermon The AUX 6 Control • Controls how much channel signal is sent to the VCR. • Always post-fader. Joe’s Rental Video The Channel EQ Controls • Make minor adjustments to tone quality of the channel. • Does not affect monitor or fold-back speakers. • Straight up (U) is flat (no EQ). • For microphones always cut, never add. Use EQ Sparingly! U EQ One or two tick marks is usually enough. On Microphone Channels Always cut, never add EQ It avoids feedback The HI EQ Control Controls High Frequencies Too much high - cut a little The LOW EQ Control Controls Low Frequencies Too much bass - cut a little The MID and FREQ EQ Controls Work Together • MID controls the amount of add or cut. • FREQ controls the frequency to be added or cut. • Set MID then sweep FREQ to get the desired effect. If you get confused….. Just put the EQ knobs to their center positions. The system should sound acceptable with the EQ flat. The LOW CUT button reduces very low.frequencies. Depress it to reduce handling and wind noise on hand-held, wireless and pulpit mikes. Leave it up for choir mikes and instruments. Now lets take a look at the Mackie video…. and learn more about how EQ works Note: The mixer in the video is different than ours but it demonstrates the concept of EQ very well. Volume The Graph you’ll see on the video…. Bass Treble Frequency 20 Hz 20,000 Hz Mackie Video Review…. • We have only one mid EQ covering 100 Hz to 8 KHz. • Our bandwidth is fixed at 1.5 octaves so there is no bandwidth control. • The concept is the same as in the video. • The HI and LOW EQ are the same. • The LOW CUT filter is the same. Continuing with our SR24-4…. The PAN Control Since we combine the mixers left and right stereo channels into a single monaural output, the PAN controls do nothing. Simply leave the PAN controls centered. The Red OL Light You’re Clipping! TURN DOWN THE TRIM! The Green Signal Light You have signal - all is well…. The MUTE Button • The only way to completely disable an input…. • Always mute unused microphones. • Always mute before connecting or disconnecting input devices. The SOLO Button • Sends the channel to headphones and VU meter. • Good for troubleshooting. • Used to set TRIM control. • Can be used to set mix. The L-R Button Signal Buss Company If you don’t assign the channel to a BUSS, the signal won’t go anywhere! For simplicity, always assign to the main L-R buss. The FADER Control • Controls how much signal goes to L-R and Post-Fade AUX outputs. • Used to set mix into main speakers. • Usually falls near “U” mark if TRIM is set properly. Now you know how to control 20 of the 24 channels Only 4 more to go! The Stereo Channels • Channels 21 and 22 are combined. • Channels 23 and 24 are combined. • Used to combine stereo output from tape and CD machines. • The only difference from mono channels is in EQ and use of the PAN control. The EQ Differences Instead of swept EQ for the mid range, channels 21/22 and 23/24 have separate HI MID and LOW MID controls. Set these for the desired effect just like you do for the HI and LOW EQ controls. Special PAN Control use • Normally set to center. • For Kids Choir split-track tapes pan left or right to send only the music track to main speaker while voice and music tracks go to monitor speakers. Now for the output side of the mixer. Don’t let it scare you - we don’t use most of it! There are 6 AUX SEND MASTERS One for each buss. Remember…. 1 - Stage monitors. 2 - Fold-back monitor. 3 - Not used. 4 - CD/Tape. 5 - Service tape recorder. 6 - VCR record. Signal Buss Company Channel AUX AUX SEND The channel AUX determines how much signal gets on the buss. The AUX SEND MASTER determines how much signal gets off the buss. Need more keyboard in the monitor mix - turn up AUX 1 on the keyboard channel. Need more of everything in the monitor mix turn up the AUX 1 SEND MASTER. Each AUX SEND has a SOLO button. Want to hear what’s going to the monitor speakers? Press the AUX 1 Send Master SOLO button. You’ll hear the whole mix. The VU Meter also reads the level of the signal going to the monitor speakers while the SOLO button is pressed. The VU Level Meter • Used to measure signal levels. • Main L/R Output if no solo buttons pressed. • Channel Signal when a solo button is pressed. The RUDE SOLO Light Flashes to warn you when the VU meter is reading a SOLO channel signal, rather than the main L-R signal. The SOLO LEVEL Sets the level of signal coming over the solo buss. Normally, set it about half way (U). The SOLO MODE • Determines if the individual channel solo is taken before or after the fader control. • Normally left in the post fade AFL (down) position. • Exception when setting TRIM controls. Never Press These!!! Pressing TAPE RETURN TO PHONES will kill all headphone output. Pressing TAPE RETURN TO MAIN MIX will kill all main speaker output. Disappearing Sound PHONES/C-R LEVEL Adjust for a comfortable headphone level. Note: C-R stands for Control Room. MAIN MIX FADER Adjusts the overall level going to the main and classroom speakers. Adjust talkback level here Push MAIN MIX for main speakers Push AUX 1&2 for stage and foldback speakers TALKBACK • Sends console mike to main, stage, and foldback speakers. • Sound Tech can talk to Choir Director during rehearsals. Now for some accessory items…. Dynamic Microphones • • • • • General purpose hand-held. Working range 3 to 6 inches. Good for solos and small groups. Low output - trim above 3/4 full. Requires no phantom power from mixer. Electret Microphones • • • • • • Condenser element with built-in preamp. Requires phantom power from mixer. Used for choir and pulpit. Sensitive - working range 2 feet or more. Exhibit bass when you get too close. High output - Trim set between 1/4 and 1/2 full. Wireless Microphones • • • • There are two wireless receivers. There are three wireless microphones…. One receiver works with a lapel mike. One receiver works with the other lapel mike OR the hand-held wireless mike, never both! Use only name brand alkaline or lithium batteries in the wireless mikes! Neveready discount battery I’m sorry The Telex Wireless Receivers Signal Light Diversity Light The Telex Wireless Receivers Diversity Light Signal Light • Signal light indicates RF signal received. • Diversity changes orange/green to indicate antenna receiving the best signal. The Diversity Receiver Reflective Surface A B Direct and Multipath signals cancel at antenna B. Receiver picks antenna A which still has a good signal. Receiver Squelch Control • Not a normal sound tech adjustment. • Located on the rear of the receiver. • Cuts receiver off to prevent “hiss” when no RF signal is present. • If set too high, sound will chop off as mike is moved about. • If set too low, “hiss” will be present when transmitter is turned off. Observe the 3 to 1 Rule for Microphone Placement 1 FT 3 FT The distance between microphones is at least 3 times the distance between the singer and his microphone. Why the 3 to 1 Rule? • Minimizes picking up the same sound with multiple microphones. • Minimizes Comb Filtering effect which…. • Often causes a “hollow” sound. • Causes sound to change with movement. When two or more microphones pick up the same sound source from different distances, Comb-Filtering is the result. Due to the difference in sound travel time, certain frequencies cancel when combined at the mixer. Comb-Filtering makes the signal sound “hollow” Volume Comb-Filtering…. “like the teeth of a comb” Bass Frequency Treble Choir Microphone Placement 6 - 9 FT 6 - 9 FT Always use the minimum number of mikes necessary to cover the area. Position the Choir Mikes • • • • 6 to 9 feet apart. 2 to 3 feet in front of the front choir row. 2 to 3 feet above the heads of the last row. Pointing at the last row. 2-3 FT 2-3 FT Always Point Mikes at the Sound Source Like this Mikes are more directional at high frequencies so they exhibit more bass off-axis. Never like this Keep the number of open mikes to a minimum…. • It improves gain before feedback. • It reduces noise and reverberation pickup. • It minimizes comb-filtering effects. Never use two when one will do! The Pro Co DB-1 Direct Box • Also known as a “DI” Box. • The most versatile. • Takes Instrument, Line, or Speaker Level Inputs. • Converts them to microphone level. • Has a HI-CUT filter for speaker inputs. • Has a ground-lift switch to reduce hum. The Pro Co DB-1 Direct Box LO-Z XLR Output to System Instrument or Speaker Output Instrument or Speaker Input Also known as a “DI” Box The Pro Co DB-1 Direct Box Ground/Lift Switch Hi-Cut/Flat Switch Speaker/Instrument Switch The Peavey Direct Box • Active - requires phantom power from the mixer. • Has the best frequency response. • Takes only line and instrument level inputs. • Converts them to microphone level outputs. • Simple to use - no switches to set. • Peavey is the first choice unless you need the versatile features of the Pro Co. The Peavey EDB-1 Direct Box DI Box Lo-Z XLR Output to System Hi-Z Input from Instrument Power Light Only two connections are needed In-Line Transformer Transformer • Small and easy to use. • Good only for instruments such as guitars. The Shure In-Line Transformer The Headset Monitor Adapter Volume Plug to monitor speaker Used for the drummer The Service Tape Machine VU Meter Record Level Normally used for recording Tape Speed Don’t use DOLBY on Church Recordings You never know if the person playing it back will have the Dolby capability. If you don’t use Dolby to record then the tape is good to play back on any machine. Make sure the Tape Speed is centered during recording!! Dolby and the Dolby is off. Tape Speed centered .…or Speed Fixed To Queue a Tape, next song…. Press Music Search >> To Queue a Tape, repeat song…. Press Music Search << The CD/TAPE Unit CD Track Select CD Controls Tape Controls Normally used for playback The CD/TAPE Unit Output Switch to MIX position or their will be no output from the CD! Make sure the tape speed is centered during recording!! Tape Speed and the Dolby switch is off. Dolby The CD/TAPE Unit Single..Cont • Single to play only selected track. • Continuous to play selected track forward. To Queue a CD Track.... 3. Press Track Number (use +10 for tracks greater than 9) 4. Press Play 2. Press Queue 1. Select Single or Continuous To Queue a Tape, next song…. Simultaneously Press…. Play and Fast Forward To Queue a Tape, repeat song…. Simultaneously Press…. Play and Rewind What is a Split-Track Tape? • A special choir tape with voices on one channel and accompaniment on the other. • Using the Split-Track tape switch, you can play back voices, accompaniment, or both. • Generally, use both during practice sessions and accompaniment during the performance. Split Track Tape Switch Selects record or playback of left only, right only, or left and right channels. HEADSET RECORD LEFT L+R CD-TAPE RIGHT SERVICE RECORDER Headset is for monitoring mixer. This switch prevents the possibility of a feed-back loop during record. You can send music and voice to the monitors with music only to the main speakers. • Good to help out the kids choir. • Switch to L + R position. • Pan mixer channel hard left or right to select music only for the main speakers. • Remember - choir mikes will pick up some voice from the monitors. The Cable Test Box A good way to check for defective cables…. 1 2 3 Never Connect Anything but Cables to the Test Box! I love it when they do that. Microphone Sales Guy To check any 3-wire cable • • • • • Mike cables with 3-pin XLR connectors 1/4-inch Tip Ring Sleeve (TRS) connectors Press button #1 and light #1 comes on Press button #2 and light #2 comes on Press button #3 and light #3 comes on To check any 2-wire cable • • • • 1/4-inch Tip Sleeve (TS) connector Press button #1 - lights #1 and #3 come on Press button #2 - light #2 comes on Press button #3 - lights #1 and #3 come on Now a word about Video…. JOHN Video System Wiring Audio from Mixer Audio to Mixer TV VCR Switch RF Modulator TV Amp TV Scan Converter TV Cart Computer Console Stage The Master Power Switch for the Video Monitors…. is located in the electric closet As a Sound Man you will normally only operate the VCR • Make sure the VCR/COMPUTER switch is in the VCR position. • Make sure the monitors are turned on and set to channel 3. • Push play on the VCR. • Un-mute and adjust the VCR channel level on the mixer for the desired volume. We’ve made it Sound Man! He’s finally done!