Download Data Sheet General Description Features (Continued)

Data Sheet
Enhanced Multi-touch Capacitive Touch Screen Controller
General Description
Features (Continued)
The AUR3852 is a low-cost high-resolution single
chip solution for APA capacitive touch screen. It is
an 8-bit single cycle 8051 microcontroller with ICP
Interface. The chip includes a 12-bit successive
approximation analog-to-digital converter with an I2C
interface and multiplexer-switcher circuits for
flexible measurement of analog signal from APA
panel. An accurate switched-capacitor integrator is
built-in and it can auto calibrate the pixel parameters
for a wide range of capacitance on the touch screen
(0.1pF to 4pF). On-chip capacitor can replace
external component. This touch screen controller
(TSC) with CMOS integration circuit provides an
ideal choice for APA touch panel. The AUR3852 is
specified over the temperature range of -40°C to
85°C.
•
The AUR3852 is available in QFN-6×6-48 and
QFN-7×7-56 packages.
•
•
•
•
•
Features
•
•
•
•
•
•
•
•
Mutual Capacitive Touch Sensing
Single Power Supply: 2.8V to 3.6V Operation
Voltage
1Supports Low Voltage to 1.8V by Built-in 1.8V
to 3.3V Boost Converter
QFN-6×6-48 Package: Up to 20 Drive Lines and
14 Sense Lines
1QFN-7×7-56 Package: Up to 27 Drive Lines and
15 Sense Lines
1Dedicated Internal Two-wire Serial Control Bus
I2C and UART between AUR3852 and Host
1Single-end Integrator with Programmable Gain
Control and Offset Control
1Multiplexed Analog Digitization with 12-bit
Resolution SAR ADC
1
AUR3852
Single Cycle 8051 CPU Core, Maximum Operating Clock up to 24MHz from IOSC
2MHz to 24MHz Internal Oscillator (IOSC)
32K-byte Flash ROM
256-byte Internal SRAM and 5888-byte
XSRAM
Two 16-bit Timers T0/T1 and One 16-bit ECT
Timer T2
One I2C Slave Controller and One I2C Master
Controller Shared with the Same Port
‹
With Asynchronous I2C Slave Address
Detection Logic Design
Up to 30 General Purpose GPIO Pins (QFN-56);
25 General Purpose GPIO Pins (QFN-48)
Up to 8 External Interrupt Pins
Up to 2 UART Ports (QFN-56); 1 UART Port
(QFN-48)
ISP/IAP via I²C/UART Port
(With External Clock I/O Pin Definition for
UART IAP. Pin Shared with P1.7)
Operation Temperature Range: -40°C to 85°C
Package Type: QFN-6×6-48 and QFN-7×7-56
RoHS Compliance
Operating Mode:
Mode
Power-down
Low speed
Standard
Description
No scan with power-down mode
Lower scan rate when finger is not
on panel, IOSC=32kHz
Higher scan rate when fingers are
on panel, IOSC can up to 2MHz
to 24MHz
Applications
•
•
•
QFN-6×6-48
Mobile Phones
Personal Digital Assistants
Smart Hand-held or Gaming Devices
QFN-7×7-56
Figure 1. Package Types of AUR3852
Feb. 2013
Rev. 1. 0
BCD Semiconductor Manufacturing Limited
1
www.BDTIC.com/DIODES
Data Sheet
Enhanced Multi-touch Capacitive Touch Screen Controller
AUR3852
Pin Configuration
S13
S12
S11
S10
S9
S8
S7
S6
S5
S4
S3
Pin 1 Mark
S14
QT Package
(QFN-6×6-48)
48
47 46
45
44
43
42
41 40
39
38
37
1
36
2
35
3
34
4
33
5
32
6
30
8
29
18
19
20
21 22
Rev. 1. 0
23
24
P0.4/PINT1.4/DR5
17
P0.5/PINT1.5/DR6
16
P0.6/TXD0/DR7
RSTN
P2.2/TXD1
P3.6/RXD1
14 15
P0.7/RXD0/DR8
25
P1.0/DR9
26
12
TESTEN
11
P1.7/T0/PINT0.1/EXTCLKIN
27
P1.3/SCL
28
P1.2/SDA
9
10
13
Feb. 2013
31
EP
7
BCD Semiconductor Manufacturing Limited
2
www.BDTIC.com/DIODES
Data Sheet
Enhanced Multi-touch Capacitive Touch Screen Controller
AUR3852
Pin Configuration (Continued)
Pin 1 Mark
XDX1
XDX0
S15
S14
S13
S12
S11
S10
S9
S8
S7
S6
S5
S4
QU Package
(QFN-7×7-56)
56
55 54
53
52
51 50
49
48
47 46
45 44
43
VSS
P1.1/DL1
1
42
2
41
P1.5/DL2
P1.6/T1/PINT0.0/DL3
P2.0/DL4
P3.1/DL5
P3.0/DL6
P2.7/DL7
P2.6/DL8
P2.5/T2/DL9
P2.4/T2EX/DL10
P2.3/DL11
P3.2/DL12
P3.3/DL13
3
40
4
39
5
38
6
37
EP
7
8
36
35
33
11
32
12
31
13
30
14
29
15
16 17 18
P2.2/TXD1
RSTN
P1.3/SCL
P1.2/SDA
TESTEN
P1.7/T0/PINT0.1/EXTCLKIN
P3.4/DR12
P3.5/DR11
P1.4/DR10
P1.0/DR9
P0.7/RXD0/DR8
P0.6/TXD0/DR7
P0.5/PINT1.5/DR6
34
10
P3.6/RXD1
9
19
20
21
22
23
24 25 26
S3
S2
S1
XCP_EN
VDDEN
VDD18
VDD
XCP
XCP_VSS
P0.0/PINT1.0/DR1
P0.1/PINT1.1/DR2
P0.2/DR3
P0.3/PINT1.3/DR4
P0.4/PINT1.4/DR5
27 28
Figure 2. Pin Configuration of AUR3852 (Top View)
Feb. 2013
Rev. 1. 0
BCD Semiconductor Manufacturing Limited
3
www.BDTIC.com/DIODES
Data Sheet
Enhanced Multi-touch Capacitive Touch Screen Controller
AUR3852
Pin Description
Pin Number
QFN-6×648
1
QFN-7×756
1
Pin
Name
Pin
Type
VSS
Power
Pin Function
Ground Voltage. 0V
Port 1.1 GPIO
2
2
P1.1
I/O
8051 P1.1 GPIO
DL1
Left driving line 1
Port 1.5 GPIO
3
3
P1.5
I/O
8051 P1.5 GPIO
DL2
Left driving line 2
Port 1.6 GPIO
8051 P1.6 GPIO
4
4
P1.6
I/O
PINT0.0
This pin can also be configured as the expanded INT0
interrupt
T1 Timer 1 Input
This pin can also be configured as Timer 1 input
DL3
Left driving line 3
5
5
P2.0
I/O
Port 2.0 GPIO
8051 P2.0 GPIO. To allow proper operation as GPIO P2.0
function, crystal oscillator must be disabled by setting
XOSCCFG register to 0x00
DL4
Left driving line 4
Port 3.1 GPIO
6
6
P3.1
I/O
8051 P3.1 GPIO
DL5
Left driving line 5
Port 3.0 GPIO
7
7
P3.0
I/O, A
8051 P3.0 GPIO
DL6
Left driving line 6
Feb. 2013
Rev. 1. 0
BCD Semiconductor Manufacturing Limited
4
www.BDTIC.com/DIODES
Data Sheet
Enhanced Multi-touch Capacitive Touch Screen Controller
AUR3852
Pin Description (Continued)
Pin Number
QFN-6×648
QFN-7×756
Pin
Name
Pin
Type
Pin Function
Port 2.7 GPIO
8
8
P2.7
I/O
8051 P2.7 GPIO
DL7
Left driving line 7
Port 2.6 GPIO
9
9
P2.6
I/O
8051 P2.6 GPIO
DL8
Left driving line 8
Port 2.5 GPIO
8051 P2.5 GPIO
10
10
P2.5
I/O
T2 Timer 2 Input
This pin can also be configured as Timer 2 input
DL9
Left driving line 9
Port 2.4 GPIO
8051 P2.4 GPIO
11
11
P2.4
I/O
T2EX Timer 2 Trigger
This pin can also be configured as T2EX signal for Timer
2. T2EX is the Timer 2 trigger input
DL10
Left driving line 10
Port 2.3 GPIO
12
12
P2.3
I/O
8051 P2.3 GPIO
DL11
Left driving line 11
Port 3.6 GPIO
13
15
P3.6
I/O
8051 P3.6 GPIO
RXD1
This pin can also be configured as RXD of UART 1
Port 2.2 GPIO
8051 P2.2 GPIO.
14
Feb. 2013
16
P2.2
I/O
TXD1
This pin can also be configured as TXD of UART 1
8051 P2.2 GPIO. To allow proper operation as GPIO P2.2
function, crystal oscillator must be disabled by setting
XOSCCFG register to 0x00
Rev. 1. 0
BCD Semiconductor Manufacturing Limited
5
www.BDTIC.com/DIODES
Data Sheet
Enhanced Multi-touch Capacitive Touch Screen Controller
AUR3852
Pin Description (Continued)
Pin Number
QFN-6×648
15, 18
QFN-7×756
17, 20
Pin
Name
RSTN,
TESTE
N
Pin
Type
Pin Function
I
Reset Low Active
Typically connect a resistor to VDD and a capacitor to
VSS
Low asserted and threshold at 0.5×VDD. When forced low,
the chip enters into reset condition
This pin should not be connected to any level above VDD
Port 1.3 GPIO
8051 P1.3 GPIO
16
18
P1.3
I/O
SCL
This pin can also be configured as the SCL signal of the
I2C master or I2C slave controller. In I2C master mode, this
pin should be configured as open-drain output. In I2C
slave mode, this pin should be configured as input only
Port 1.2 GPIO
8051 P1.2 GPIO
17
19
P1.2
I/O
SDA
This pin can also be configured as the SDA signal of the
I2C master or I2C slave controller. In this operation mode,
this pin should also be configured as bi-directional I/O
with open-drain output
Port 1.7 GPIO
8051 P1.7 GPIO
19
21
P1.7
I/O
PINT0.1
This pin can also be configured as the expanded INT0
interrupt
T0 Timer 0 Input
This pin can also be configured as Timer 0 input
External Clock Input
External clock input source
Port 1.0 GPIO
20
25
P1.0
I/O
8051 P1.0 GPIO
DR9
Right driving line 9
21
26
P0.7
I/O
Port 0.7 GPIO
8051 P0.7 GPIO
RXD0
This pin can also be configured as RXD of UART 0
DR8
Right driving line 8
Feb. 2013
Rev. 1. 0
BCD Semiconductor Manufacturing Limited
6
www.BDTIC.com/DIODES
Data Sheet
Enhanced Multi-touch Capacitive Touch Screen Controller
AUR3852
Pin Description (Continued)
Pin Number
QFN-6×648
QFN-7×756
Pin
Name
Pin
Type
Pin Function
Port 0.6 GPIO
8051 P0.6 GPIO
22
27
P0.6
I/O
TXD0
This pin can also be configured as TXD of UART 0
DR7
Right driving line 7
Port 0.5 GPIO
8051 P0.5 GPIO
23
28
P0.5
I/O
PINT1.5
This pin can also be configured as the expanded INT1
interrupt
DR6
Right driving line 6
24
29
P0.4
I/O
25
30
P0.3
I/O
26
31
P0.2
I/O
Port 0.4 GPIO
8051 P0.4 GPIO
PINT1.4
This pin can also be configured as the expanded INT1
interrupt
DR5
Right driving line 5
Port 0.3 GPIO
8051 P0.3 GPIO
PINT1.3
This pin can also be configured as the expanded INT1
interrupt
DR4
Right driving line 4
Port 0.2 GPIO
8051 P0.2 GPIO
DR3
Right driving line 3
Port 0.1 GPIO
8051 P0.1 GPIO
27
32
P0.1
I/O
PINT1.1
This pin can also be configured as the expanded INT1
interrupt.
DR2
Right driving line 2
Feb. 2013
Rev. 1. 0
BCD Semiconductor Manufacturing Limited
7
www.BDTIC.com/DIODES
Data Sheet
Enhanced Multi-touch Capacitive Touch Screen Controller
AUR3852
Pin Description (Continued)
Pin Number
QFN-6×648
QFN-7×756
Pin
Name
Pin
Type
Pin Function
Port 0.0 GPIO
8051 P0.0 GPIO
28
33
P0.0
I/O
PINT1.0
This pin can also be configured as the expanded INT1
interrupt
DR1
Right driving line 1
29
34
XCP_
VSS
Power
30
35
XCP
Power
31
36
VDD
Power
32
37
VDD1
8
Power
33
38
VDDE
N
I
34
39
XCP_E
N
I
35
40
S1
I/O, A
41,42 43,
44, 45, 46,
47, 48, 49,
50, 51, 52,
53, 54
S2, S3,
S4, S5,
S6, S7,
S8, S9,
S10,
S11,
S12,
S13,
S14,
S15
I, A
36, 37, 38,
39, 40, 41,
42, 43, 44,
45, 46, 47,
48, -
Ground Voltage. 0V
Boost Ground
Supply Voltage. 1.6V to 2.0V
1.8V boost in
Supply Voltage. 2.8V to 3.6V
A good decoupling capacitor between VDD and VSS pins
is critical for good performance
Internal Regulator Output. 1.6V to 2.0V
Typical decoupling capacitors of 0.1µF and 10µF should
be connected between VDD18 and VSS
CPU Power Supply Enable
Supply voltage enable for 8051 CPU
1.8V to 3.3V Boost Converter Enable
3.3V Boost Supply voltage enable for 1.8V power input
S1
Sensing line 1
S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S13, S14,
S15
Sensing line 2 to 15
Port 3.2 GPIO
-
13
P3.2
I/O
8051 P3.2 GPIO
DL12
Left driving line 12
Feb. 2013
Rev. 1. 0
BCD Semiconductor Manufacturing Limited
8
www.BDTIC.com/DIODES
Data Sheet
Enhanced Multi-touch Capacitive Touch Screen Controller
AUR3852
Pin Description (Continued)
Pin Number
QFN-6×648
QFN-7×756
Pin
Name
Pin
Type
Pin Function
Port 3.3 GPIO
-
14
P3.3
I/O
8051 P3.3 GPIO
DL13
Left driving line 13
Port 3.4 GPIO
-
22
P3.4
I/O
8051 P3.4 GPIO
DR12
Right driving line 12
Port 3.5 GPIO
-
23
P3.5
I/O
8051 P3.5 GPIO
DR11
Right driving line 11
Port 1.4 GPIO
-
24
P1.4
I/O
8051 P1.4 GPIO
DR10
Right driving line 10
-
Feb. 2013
55,56
XDX0,
XDX1
I, A
Driving line 26,27
Rev. 1. 0
BCD Semiconductor Manufacturing Limited
9
www.BDTIC.com/DIODES
Data Sheet
Enhanced Multi-touch Capacitive Touch Screen Controller
AUR3852
Functional Block Diagram
32KB Flash
6KB SRAM
Figure 3. Main AFE I/O Pin Assignment and Whole Chip’s Functional Block Diagram
Feb. 2013
Rev. 1. 0
BCD Semiconductor Manufacturing Limited
10
www.BDTIC.com/DIODES
Data Sheet
Enhanced Multi-touch Capacitive Touch Screen Controller
AUR3852
Ordering Information
AUR3852
QT: QFN-6×6-48
QU: QFN-7×7-56
Circuit Type
G: Green
Package
Temperature Range
Part Number
QFN-6x6-48
Marking ID
Packing Type
AUR3852GQT
A3852GQT
Tape & Reel
AUR3852GQU
A3852GQU
Tape & Reel
-40 to 85°C
QFN-7x7-56
BCD Semiconductor's Pb-free products, as designated with "G" in the part number, are RoHS compliant and
green.
AUR3852 Support 4” to 7” Touch Panel, Listed Below:
PN
TX/RX
Multi-touch
Package
Panel size
AUR3852GQT
20/14
10 point 100Hz
QFN-6x6-48
4” to 5”
AUR3852GQU
27/15
10 point 100Hz
QFN-7x7-56
5” to 7”
Absolute Maximum Ratings (Note 1)
Parameter
Symbol
Value
Unit
VDD
2.8 to 3.6
V
Analog Input Voltage (Other pins)
-0.3 to VDD+0.3
V
Logic Input Voltage
-0.3 to VDD+0.3
V
Supply Voltage
Power Dissipation
PD
250
mW
Maximum Junction Temperature
TJ
100
°C
Operating Temperature
TOP
-40 to 85
°C
Storage Temperature
TSTG
-65 to 150
°C
Note 1: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to
the device. These are stress ratings only, and functional operation of the device at these or any other conditions
beyond those indicated under “Recommended Operating Conditions” is not implied. Exposure to “Absolute
Maximum Ratings” for extended periods may affect device reliability.
Feb. 2013
Rev. 1. 0
BCD Semiconductor Manufacturing Limited
11
www.BDTIC.com/DIODES
Data Sheet
Enhanced Multi-touch Capacitive Touch Screen Controller
AUR3852
Electrical Characteristics
DA/AC Characteristics for AFE
TA=–40°C to 85°C, VDD=3.3V, I2C bus frequency=400kHz, 12-bit mode, unless otherwise noted.
Parameter
Symbol
ADC DC Accuracy
Resolution
No Missing Codes
Integral Linearity Error
INL
Differential Linearity Error
Offset Error
DNL
Gain Error
Analog Input
Full-scale Input Span
Absolute Input Range
ADC Sampling Dynamics
Throughput Rate
Reference Input
Input Voltage Range
Switched-capacitor Integrator
Output Voltage Range
Integrator Capacitor
CINT
Power Supply
Supply Voltage
VDD
Charge Pump Voltage
XCP
Operating Current
Standard/Fast mode
Standard/Fast mode
Feb. 2013
Typ
11
Max
Unit
12
±6
±4
Bits
Bits
LSB
LSB
LSB
LSB
VDD
VDD+0.2
V
V
12
±3
±1.5
External VREF
0
-0.2
250
ksps
1.8
VDD
V
0.3
VDD-0.3
V
pF
3.6
3.6
V
V
12
Operating voltage
2.8
1.8
TBD
mA
TBD
µA
3
µA
1
-40
VDD18,
15mA
2.0
V
-2/4/6
0
2/4/6
%
24
MHz
frequency
Rev. 1. 0
µA
50
0
2
frequency=
°C
1.8
-10/20/
30
Operating
12MHz
85
1.6
2
Operating
=12MHz
Frequency
Trimming
Level
External Clock
Frequency
Operating Current
Min
Standard mode: IOSC=
2MHz to 24MHz
Low-speed mode: IOSC
=32KHz
Power-down
mode,
VDDEN=low
Quiescent Current
Temperature Range
Specified Performance
3.3V to 1.8V LDO
Internal 1.8V Regulator
Output
Output Voltage Trimming
Level
Internal OSC
Frequency
Test Condition
50
10/20/30
%
24
MHz
µA
BCD Semiconductor Manufacturing Limited
12
www.BDTIC.com/DIODES
Data Sheet
Enhanced Multi-touch Capacitive Touch Screen Controller
AUR3852
Electrical Characteristics (Continued)
DA/AC Characteristics for 8051 CPU Core, Digital GPIO pins, Digital Peripherals, and
IOSC
TA=–40°C to 85°C, VDD=2.8V to 3.6V, unless otherwise noted.
Parameter
Power Supply Current
Normal Mode Supply Current
Using IOSC up to 24MHz
Normal Mode Supply Current
Using IOSC<4MHz
PMM Mode Supply Current Using
IOSC up to 24MHz
PMM Mode Supply Current Using
IOSC<4MHz
Idle Mode Supply Current Using
IOSC up to 24MHz
Stop Mode Supply Current Using
IOSC Keeps Low, VDDEN=low
Digital GPIO Characteristics
High Level Input Voltage
Low Level Input Voltage
High Level Output Voltage
Low Level Output Voltage
High Level
@VOH(min)
Output
Current
Low Level
@VOL(max)
Output
Current
Symbol
Min
Typ
Max
Unit
Note
IDD, normal IOSC1
7
mA
2
IDD, normal IOSC2
2.5
mA
2
IDD, PMM IOSC1
2.5
mA
2
IDD, PMM IOSC2
0.5
mA
2
IDD, idle IOSC1
2.5
mA
2
IDD, stop
3
µA
2
V
V
V
V
V
V
mA
mA
mA
mA
kΩ
kΩ
V
V
ns
ns
3
3
3
3
V
%
5
6
VIH
VIH, SDA/SCL
VIL
VIL, SDA/SCL
VOH
VOL
IOH(2mA)
IOH(4mA)
IOL(2mA)
IOL(4mA)
RPU
RPD
VIH, RSTN
VIL, RSTN
tRISE
tFALL
Input Pull Up Resistance
Input Pull Down Resistance
Input Low to High Level, RSTN
Input High to Low Level, RSTN
Output Rise Time
Output Fall Time
Internal 3.3V to 1.8V LDO from AFE
Internal 1.8V Regulator Output
VDD18, 15mA
Power On/Off Reset Level
VDD18, Reset
2
1.6
-0.3
-0.3
2.4
3.0
7.7
3.4
6.7
34
29
1.56
1.16
3.6
3.6
0.8
0.5
7.8
15.6
5.4
10.7
0.4
12.9
25.8
7.4
14.7
74
86
1.71
1.30
5
5
1.6
80
1.8
85
2.0
90
3
3
4
4
7
7
Note 2: Does not include load current and tested under NOP loop and all peripheral disabled.
Note 3: For Digital I/O only.
Note 4: For RSTN pin only.
Note 5: Supply to internal digital and analog circuit only.
Note 6: This is measured as the percentage of steady state value of VDD18.
Note 7: This is measured with 20pF load and 20% to 80% output level.
Feb. 2013
Rev. 1. 0
BCD Semiconductor Manufacturing Limited
13
www.BDTIC.com/DIODES
Data Sheet
Enhanced Multi-touch Capacitive Touch Screen Controller
AUR3852
Typical Application
Figure 4. Typical Application of AUR3852 (For QFN-7×7-56 Package)
Feb. 2013
Rev. 1. 0
BCD Semiconductor Manufacturing Limited
14
www.BDTIC.com/DIODES
Data Sheet
Enhanced Multi-touch Capacitive Touch Screen Controller
AUR3852
Mechanical Dimensions
QFN-6×6-48
5.900(0. 232)
6.100(0. 240)
Unit: mm(inch)
0.300(0. 012)
0.500(0. 020)
4.400(0. 173)
4.600(0. 181)
N25
N37
5.900(0.232)
6.100(0.240)
4.400(0. 173)
4.600(0. 181)
Pin 1 Mark
0.250(0. 010)
MIN
N13
N48
N1
PIN # 1 IDENTIFICATION
0.400(0. 016)
BSC
See DETAIL A
DETAIL A
0.700(0. 028)
0.800(0. 031)
0.000(0. 000)
0.050(0. 002)
0.150(0. 006)
0.250(0. 010)
0.200(0. 008)
REF
3
2
1
46
46
46
47
47
47
48
48
48
3
2
1
3
2
1
Pin 1 Options
Feb. 2013
Rev. 1. 0
BCD Semiconductor Manufacturing Limited
15
www.BDTIC.com/DIODES
Data Sheet
Enhanced Multi-touch Capacitive Touch Screen Controller
AUR3852
Mechanical Dimensions (Continued)
QFN-7×7-56
Feb. 2013
Rev. 1. 0
Unit: mm(inch)
BCD Semiconductor Manufacturing Limited
16
www.BDTIC.com/DIODES
BCD Semiconductor Manufacturing Limited
http://www.bcdsemi.com
IMPORTANT NOTICE
BCD Semiconductor Manufacturing Limited reserves the right to make changes without further notice to any products or specifications herein. BCD Semiconductor Manufacturing Limited does not assume any responsibility for use of any its products for any
IMPORTANT NOTICE
IMPORTANT
NOTICE
particular purpose, nor does BCD Semiconductor Manufacturing Limited assume any liability arising out of the application or use
of any its products or circuits. BCD Semiconductor Manufacturing Limited does not convey any license under its patent rights or
BCD Semiconductor
BCD
Semiconductor Manufacturing
Manufacturing Limited
Limited reserves
reserves the
the right
right to
to make
make changes
changes without
without further
further notice
notice to
to any
any products
products or
or specifispecifiother rights nor the rights of others.
cations herein.
cations
herein. BCD
BCD Semiconductor
Semiconductor Manufacturing
Manufacturing Limited
Limited does
does not
not assume
assume any
any responsibility
responsibility for
for use
use of
of any
any its
its products
products for
for any
any
particular
particular
purpose,
purpose,
nor
nor
does
does
BCD
BCD
Semiconductor
Semiconductor
Manufacturing
Manufacturing
Limited
Limited
assume
assume
any
any
liability
liability
arising
arising
out
out
of
of
the
the
application
application
or
or
use
use
MAIN SITE
ofHeadquarters
any its
any
its products
products or
or circuits.
circuits. BCD
BCD Semiconductor
Semiconductor Manufacturing
Manufacturing
Limited
does not
does
not convey
convey any
any license
license under
under its
its patent
patent rights
rights or
or
-of
- Wafer Limited
Fab
BCD
(Shanghai)
Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd.
other
other
rights Micro-electronics
rights
nor the
nor
the rights
rightsLimited
of others.
of
others.
No. 1600, Zi Xing Road, Shanghai ZiZhu Science-based Industrial Park, 200241, P. R.C.
Tel: +86-021-2416-2266, Fax: +86-021-2416-2277
800 Yishan Road, Shanghai 200233, China
Tel: +021-6485-1491, Fax: +86-021-5450-0008
MAIN SITE
SITE
MAIN
REGIONAL
SALES Manufacturing
OFFICE
- Headquarters
BCD
Semiconductor
Limited
- Wafer
FabSemiconductor Manufacturing Limited
BCD
BCD
Semiconductor
Manufacturing Limited
Shanghai
SIM-BCD
Semiconductor Manufacturing Co., Ltd.
Shenzhen
Office
Taiwan
Office
(Taipei)
- Wafer
Fab
- IC Design
Group
No.
1600, Zi
Xing Road,
Shanghai ZiZhu
Science-basedCo.,
Industrial
Park, 200241,
China
Yi
Shan Road,
Shanghai
200233,
China
Shanghai
SIM-BCD
Semiconductor
Manufacturing
Ltd., Shenzhen
Office
BCD800
Semiconductor
(Taiwan)
Company
Limited
Shanghai
SIM-BCD
Semiconductor
Manufacturing
Limited
Advanced
Analog
Circuits
(Shanghai)
Corporation
Tel:
Fax: +86-21-24162277
Tel: +86-21-6485
1491,
0008Dist.,
Unit
A
1203,Skyworth
Bldg.,
Gaoxin
3F, No.17,
Lane
171,
Sec.
2,
Jiu-Zong
Rd.,Shanghai
Nei-Hu
Taipei(114),
Taiwan, R.O.C
800,+86-21-24162266,
YiRoom
Shan Road,
Shanghai
200233,
ChinaAve.1.S., Nanshan District
8F,
Zone
B, 900,
YiFax:
Shan+86-21-5450
Road,
200233,
China
Shenzhen
518057,1491,
ChinaFax: +86-21-5450 0008
Tel: +886-2-2656
2808
Tel: +86-21-6485
Tel: +86-21-6495
9539, Fax: +86-21-6485 9673
REGIONAL
SALES OFFICE
Tel: +86-0755-8660-4900,
Fax: +86-0755-8660-4958
Fax: +886-2-2656-2806/26562950
Shenzhen OfficeSALES OFFICE
Taiwan Office
USA Office
REGIONAL
Shanghai
SIM-BCD
Semiconductor Manufacturing Co., Ltd., Shenzhen Office
Semiconductor
BCD Office
Semiconductor Corp.
Taiwan
Office
(Hsinchu)
USABCD
Office
Korea Office USA
Shenzhen
Office
Taiwan
Office (Taiwan) Company Limited
Unit
ASemiconductor
Room
1203, Skyworth
Gaoxin
Ave.1.S., Nanshan
Shenzhen,
4F,Semiconductor
298-1,
Guang
Road,(Taiwan)
Nei-Hu District,
Taipei,
30920Semiconductor
Huntwood
Ave.Corporation
Hayward,
BCD
(Taiwan)Bldg.,
Company
Limited
BCD
Corp.
BCD
Semiconductor
Limited Korea
office.
Shanghai
SIM-BCD
Semiconductor
Manufacturing
Co., Ltd.District,
Shenzhen
Office
BCDRui
Semiconductor
Company
Limited
BCD
China
Taiwan
CADigital-Empire
94544,
USA Ave.
8F,
No.176,Analog
Sec. 2, Gong-Dao
5th Road, Corporation
East District Shenzhen Office
48460
Kato
CARoad,
94538,
USA District,
Room
101-1112,
II, 486
Sin-dong,
Advanced
Circuits (Shanghai)
4F,Road,
298-1,Fremont,
Rui Guang
Nei-Hu
Taipei,
30920
Huntwood
Hayward,
Tel:
+86-755-8826
7951
+886-2-2656
2808
Tel
:94544,
+1-510-324-2988
HsinChu
300, Taiwan,
R.O.C 3rd Fuzhong Road, Futian District, Shenzhen 518026, China
Tel:Tel:
+1-510-668-1950
Yeongtong-Gu,
Suwon-city,
Gyeonggi-do, Korea
Room
E, City
5F, Noble
Center, No.1006,
Taiwan
CA
U.S.A
Fax:
+86-755-8826
7865
Fax:
+886-2-2656
2806
Fax:
+1-510-324-2788
Tel:
+886-3-5160181,
Fax:
+886-3-5160181
Fax:
+1-510-668-1990
Tel:
+82-31-695-8430
Tel: +86-755-8826 7951
Tel: +886-2-2656 2808
Tel : +1-510-324-2988
Fax: +86-755-8826 7865
Fax: +886-2-2656 2806
Fax: +1-510-324-2788
www.BDTIC.com/DIODES