Download Evaluates: MAX1744/MAX1745 MAX1744 Evaluation Kit General Description Features

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Spark-gap transmitter wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Solar micro-inverter wikipedia , lookup

Capacitor wikipedia , lookup

Electrical ballast wikipedia , lookup

Three-phase electric power wikipedia , lookup

Electrical substation wikipedia , lookup

Ohm's law wikipedia , lookup

History of electric power transmission wikipedia , lookup

Islanding wikipedia , lookup

Pulse-width modulation wikipedia , lookup

Variable-frequency drive wikipedia , lookup

Distribution management system wikipedia , lookup

Power inverter wikipedia , lookup

Triode wikipedia , lookup

Current source wikipedia , lookup

Two-port network wikipedia , lookup

Power MOSFET wikipedia , lookup

Integrating ADC wikipedia , lookup

Alternating current wikipedia , lookup

Surge protector wikipedia , lookup

Stray voltage wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Rectifier wikipedia , lookup

Power electronics wikipedia , lookup

Schmitt trigger wikipedia , lookup

Voltage optimisation wikipedia , lookup

Voltage regulator wikipedia , lookup

Mains electricity wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Buck converter wikipedia , lookup

Current mirror wikipedia , lookup

Opto-isolator wikipedia , lookup

Transcript
19-1817; Rev 0; 10/00
MAX1744 Evaluation Kit
Features
♦ High Input Voltage (up to 36V)
This EV kit is a fully assembled and tested circuit
board. It can also be used to evaluate the MAX1745,
which has an adjustable output voltage, by selecting
feedback resistors R2 and R3.
♦ Up to 330kHz Switching Frequency
♦ Selectable 3.3V or 5V Output Voltage (MAX1744)
♦ 1.25V to 18V Adjustable Output Voltage
(MAX1745)
♦ Low Dropout Voltage
♦ 100% Maximum Duty Cycle
♦ 2A Output Current
♦ 4µA IC Shutdown Current
♦ 10-Pin µMAX Package
♦ Fully Assembled and Tested
Ordering Information
PART
TEMP. RANGE
MAX1744EVKIT
0°C to +70°C
IC PACKAGE
10 µMAX
Note: To evaluate the MAX1745, request a MAX1745EUB free
sample with the MAX1744EVKIT.
Component List
DESIGNATION
QTY
C1, C2
2
C3
1
C4, C5
2
C6
1
C7
1
D1
L1
1
1
DESCRIPTION
120µF, 63V electrolytic
capacitors
Sanyo 63MV120GX
220µF, 10V tantalum capacitor
AVX TPSE227M010R0100 or
Sprague 593D227X0010E 2W
4.7µF, 16V tantalum capacitors
Sprague 595D475X0016A 2B
0.1µF ceramic capacitor (1206)
0.47µF ceramic capacitor (1206)
2A, 60V Schottky diode
Nihon EC21QS06 or
Central Semiconductor CMSH2-60
22µH inductor
Sumida CDRH104R-220MC
(shielded), Sumida CDRH124220MC (shielded),
Coilcraft DO3316P-223
(unshielded), or Coiltronics
UP2B-220 (unshielded)
DESIGNATION
QTY
P1
1
R1
1
R2, R3
0
DESCRIPTION
60V P-channel MOSFET
Fairchild NDS9407
0.033Ω ±1% resistor (2010)
Dale WSL-2010-R033F or
IRC LR2010-R033F
Not installed
MAX1744EUB (10-pin µMAX)
U1
1
JU1, JU2
2
3-pin headers
None
2
Shunts
None
1
MAX1744/MAX1745 PC board
None
1
MAX1744/MAX1745 data sheet
None
1
MAX1744 EV kit data sheet
________________________________________________________________ Maxim Integrated Products
1
For price, delivery, and to place orders, please contact Maxim Distribution at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
www.BDTIC.com/maxim
Evaluates: MAX1744/MAX1745
General Description
The MAX1744 evaluation kit (EV kit) provides a selectable 3.3V or 5V output voltage from input as high as
36V. The MAX1744 operates up to 100% duty cycle,
extending the usable input voltage range. The 100%
duty cycle and a low 100mV current-sense level permit
very low dropout voltages. The circuit is configured to
deliver up to 2A of output current with greater than 90%
conversion efficiency. The output current can be
increased by changing the external components.
Evaluates: MAX1744/MAX1745
MAX1744 Evaluation Kit
Quick Start
Detailed Description
The MAX1744 EV kit is fully assembled and tested.
Follow these steps to verify board operation. Do not
turn on the power supply until all connections are
completed:
1) Verify that the shunt on JU1 is across pins 1 and 2.
Evaluating Other Output Voltages
2) Verify that the shunt on JU2 is across pins 1 and 2
for a 5V output.
3) Connect a voltmeter and load, if any, to the VOUT
pad.
4) Connect a 5.5V to 36V supply voltage to the VIN
pad. Connect ground to the GND pad.
To generate output voltages other than 3.3V or 5V,
replace the MAX1744 with the MAX1745 (adjustable
output), and select the external voltage-divider resistors, R2 and R3. The MAX1745 allows the output voltage to be set from 1.25V to 18V. The only other modification required is to remove the shunt from JU2. For
output voltages greater than 5V, replace output capacitor C3 with a higher voltage rating. Refer to the Setting
the Output Voltage section in the MAX1744/
MAX1745 data sheet for instructions on calculating R2
and R3 values.
5) Turn on the power supply. Verify that the output
voltage is 5V.
6) Remove the shunt from JU2 pins 1 and 2, and place
it across pins 2 and 3 for a 3.3V output voltage.
Component Suppliers
Table 1. Jumper JU1 Functions
(Shutdown Mode)
SUPPLIER
SHUNT
LOCATION
SHDN PIN
OUTPUT
VOLTAGE
1 and 2
Connected to VL
Connected to
GND
MAX1744 enabled
Shutdown mode,
VOUT = 0
2 and 3
Table 2. Jumper JU2 Functions
(Output Voltage Selection)
SHUNT
LOCATION
1 and 2
2 and 3
2
3/5 PIN
Connected to VL
Connected to
GND
OUTPUT
VOLTAGE
VOUT = 5V
VOUT = 3.3V
PHONE
FAX
AVX
803-946-0690
803-626-3123
Central
Semiconductor
516-435-1110
516-435-1824
Coilcraft
708-639-6400
708-639-1469
Coiltronics
561-241-7876
561-241-9339
Dale-Vishay
402-564-3131
402-563-6418
Fairchild
408-721-2181
408-721-1635
IRC
361-992-7900
361-992-3377
Nihon
847-843-7500
847-843-2798
Sanyo
619-661-6835
619-661-1055
Sprague
603-224-1961
603-224-1430
Sumida
708-956-0666
708-956-0702
Note: Please indicate that you are using the MAX1744/MAX1745
when contacting these component suppliers.
_______________________________________________________________________________________
www.BDTIC.com/maxim
MAX1744 Evaluation Kit
Evaluates: MAX1744/MAX1745
VIN
36V MAX
C4
4.7µF
16V
10
SHDN
8
VH
EXT
4 1
9
JU1
2
2
3
P1
5
C7
0.47µF
VIN
1
V+
6
8
7
L1
22µH
7
SHDN
3
VL
5V
2
VL
REF
1.25V
GND
CS
OUT
VOUT
5V, 2A
R1
0.033Ω
C3
220µF
10V
D1
U1
MAX1744
MAX1745
C5
4.7µF
16V
C2
120µF
63V
C1
120µF
63V
1
GND
6
5
VL
3
REF
C6
0.1µF
(FB)
3/5
1
JU2
4
2
3
R2
OPEN
R3
OPEN
( ) ARE FOR MAX1745 ONLY.
Figure 1. MAX1744 EV Kit Schematic
_______________________________________________________________________________________
www.BDTIC.com/maxim
3
Evaluates: MAX1744/MAX1745
MAX1744 Evaluation Kit
1.0"
1.0"
Figure 2. MAX1744 EV Kit Component Placement Guide—Top
Silkscreen
Figure 3. MAX1744 EV Kit Component Placement Guide—
Bottom Silkscreen
1.0"
1.0"
Figure 4. MAX1744 EV Kit PC Board Layout—Component Side
Figure 5. MAX1744 EV Kit PC Board Layout—Solder Side
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
4 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2000 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
www.BDTIC.com/maxim