Download High-Voltage, High-Current OPERATIONAL AMPLIFIER DESCRIPTION FEATURES

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Control system wikipedia , lookup

Solar micro-inverter wikipedia , lookup

Tube sound wikipedia , lookup

Power engineering wikipedia , lookup

Mercury-arc valve wikipedia , lookup

Audio power wikipedia , lookup

Electrical substation wikipedia , lookup

Transistor wikipedia , lookup

Three-phase electric power wikipedia , lookup

Electrical ballast wikipedia , lookup

History of electric power transmission wikipedia , lookup

Pulse-width modulation wikipedia , lookup

Ohm's law wikipedia , lookup

Power inverter wikipedia , lookup

Triode wikipedia , lookup

Amplifier wikipedia , lookup

Islanding wikipedia , lookup

Variable-frequency drive wikipedia , lookup

Two-port network wikipedia , lookup

Stray voltage wikipedia , lookup

Thermal runaway wikipedia , lookup

Distribution management system wikipedia , lookup

Surge protector wikipedia , lookup

Power MOSFET wikipedia , lookup

Current source wikipedia , lookup

Schmitt trigger wikipedia , lookup

Rectifier wikipedia , lookup

Voltage optimisation wikipedia , lookup

Voltage regulator wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Alternating current wikipedia , lookup

Mains electricity wikipedia , lookup

Buck converter wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Current mirror wikipedia , lookup

Opto-isolator wikipedia , lookup

Transcript
OPA547
OPA
547
OPA
547
OPA
547
SBOS056F – JANUARY 2002 – JULY 2005
High-Voltage, High-Current
OPERATIONAL AMPLIFIER
FEATURES
DESCRIPTION
● WIDE SUPPLY RANGE
Single Supply: +8V to +60V
Dual Supply: ±4V to ±30V
● HIGH OUTPUT CURRENT:
500mA Continuous
● WIDE OUTPUT VOLTAGE SWING
● FULLY PROTECTED:
Thermal Shutdown
Adjustable Current Limit
● OUTPUT DISABLE CONTROL
● THERMAL SHUTDOWN INDICATOR
● HIGH SLEW RATE: 6V/µs
● LOW QUIESCENT CURRENT
● PACKAGES:
7-Lead TO-220, Zip and Straight Leads
7-Lead DDPAK Surface-Mount
The OPA547 is a low-cost, high-voltage/high-current operational amplifier ideal for driving a wide variety of loads. A
laser-trimmed monolithic integrated circuit provides excellent
low-level signal accuracy and high output voltage and current.
The OPA547 operates from either single or dual supplies for
design flexibility. In single-supply operation, the input common-mode range extends below ground.
The OPA547 is internally protected against over-temperature
conditions and current overloads. In addition, the OPA547
was designed to provide an accurate, user-selected current
limit. Unlike other designs which use a “power” resistor in
series with the output current path, the OPA547 senses the
load indirectly. This allows the current limit to be adjusted
from 0mA to 750mA with a 0 to 150µA control signal. This is
easily done with a resistor/potentiometer or controlled digitally with a voltage-out or current-out DAC.
The Enable/Status (E/S) pin provides two functions. An input
on the pin not only disables the output stage to effectively
disconnect the load, but also reduces the quiescent current
to conserve power. The E/S pin output can be monitored to
determine if the OPA547 is in thermal shutdown.
APPLICATIONS
●
●
●
●
●
●
VALVE, ACTUATOR DRIVERS
SYNCHRO, SERVO DRIVERS
POWER SUPPLIES
TEST EQUIPMENT
TRANSDUCER EXCITATION
AUDIO AMPLIFIERS
The OPA547 is available in an industry-standard
7-lead staggered and straight lead TO-220 package, and a
7-lead DDPAK surface-mount plastic power package. The
copper tab allows easy mounting to a heat sink or circuit
board for excellent thermal performance. It is specified for
operation over the extended industrial temperature range,
–40°C to +85°C.
V+
–
VIN
OPA547
VO
ILIM
+
VIN
RCL (1/4 Watt Resistor)
RCL sets the current limit
value from 0 to 750mA.
E/S
V–
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
www.BDTIC.com/TI
Copyright © 2002-2005, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
www.ti.com
ABSOLUTE MAXIMUM RATINGS(1)
ELECTROSTATIC
DISCHARGE SENSITIVITY
Output Current ................................................................. See SOA Curve
Supply Voltage, V+ to V– ................................................................... 60V
Input Voltage .................................................. (V–) – 0.5V to (V+) + 0.5V
Input Shutdown Voltage ........................................................................ V+
Operating Temperature .................................................. –40°C to +125°C
Storage Temperature ..................................................... –55°C to +125°C
Junction Temperature ...................................................................... 150°C
Lead Temperature (soldering 10s)(2) .............................................. 300°C
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
NOTES: (1) Stresses above these ratings may cause permanent damage. (2)
Vapor-phase or IR reflow techniques are recommended for soldering the
OPA547F surface-mount package. Wave soldering is not recommended due to
excessive thermal shock and “shadowing” of nearby devices.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may be
more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
PACKAGE/ORDERING INFORMATION
For the most current package and ordering information, see the Package Ordering Addendum at the end of this document, or see
the TI website at www.ti.com.
PIN CONFIGURATIONS
Top Front View
7-Lead
Stagger-Formed
TO-220 (T)
7-Lead
Straight-Formed
TO-220 (T-1)
1 2 3 4 5 6 7
7-Lead
DDPAK (FA)
Surface-Mount
1 2 3 4 5 6 7
1 2 3 4 5 6 7
VIN+ ILIM V+ E/S
VIN– V– VO
VIN+ ILIM V+ E/S
VIN– V– VO
VIN+ ILIM V+ E/S
VIN– V– VO
NOTE: Tabs are electrically connected to the V– supply.
2
www.BDTIC.com/TI
www.ti.com
OPA547
SBOS056F
ELECTRICAL CHARACTERISTICS
At TCASE = +25°C, VS = ±30V and E/S pin open, unless otherwise noted.
OPA547T, F
PARAMETER
CONDITION
OFFSET VOLTAGE
Input Offset Voltage
vs Temperature
vs Power Supply
INPUT BIAS CURRENT(1)
Input Bias Current(2)
vs Temperature
Input Offset Current
MIN
TYP
MAX
UNITS
VCM = 0, IO = 0
TA = –40°C to +85°C
VS = ±4V to ±30V
±1
±25
10
±5
mV
µV/°C
µV/V
VCM = 0V
–100
±0.5
±5
VCM = 0V
NOISE
Input Voltage Noise Density, f = 1kHz
Current Noise Density, f = 1kHz
INPUT VOLTAGE RANGE
Common-Mode Voltage Range: Positive
Negative
Common-Mode Rejection
Linear Operation
Linear Operation
VCM = (V–) –0.1V to (V+) –3V
(V+) –3
(V–) –0.1
80
INPUT IMPEDANCE
Differential
Common-Mode
OPEN-LOOP GAIN
Open-Loop Voltage Gain, f = 10Hz
FREQUENCY RESPONSE
Gain-Bandwidth Product
Slew Rate
Full-Power Bandwidth
Settling Time: ±0.1%
Total Harmonic Distortion + Noise, f = 1kHz
OUTPUT
Voltage Output, Positive
Negative
Positive
Negative
Maximum Continuous Current Output: dc
ac
Leakage Current, Output Disabled, dc
Output Current Limit
Current Limit Range
Current Limit Equation
Current Limit Tolerance(1)
VO = ±25V, RL = 1kΩ
VO = ±25V, RL = 50Ω
100
RL = 50Ω
G = 1, 50VPP, RL = 50Ω
G = –10, 50V Step
RL = 50Ω, G = +3V, 1W Power
IO = 0.5A
IO = –0.5A
IO = 0.1A
IO = –0.1A
(V+) –2.2
(V–) +1.6
(V+) –1.8
(V–) +1.2
±500
500
100
–500
±50
nA
nA/°C
nA
90
200
nV/√Hz
fA/√Hz
(V+) –2.3
(V–) –0.2
95
V
V
dB
107 || 6
109 || 4
Ω || pF
Ω || pF
115
110
dB
dB
1
6
See Typical Curve
18
0.004(3)
MHz
V/µs
kHz
µs
%
(V+) –1.9
(V–) +1.3
(V+) –1.5
(V–) +0.8
V
V
V
V
mA
mArms
See Typical Curve
0 to ±750
ILIM = (5000)(4.75)/(31600Ω + RCL)
±10
±30
RCL = 31.6kΩ (ILIM = ±375mA),
RL = 50Ω
mA
A
mA
See Typical Curve(4)
Capacitive Load Drive
OUTPUT ENABLE /STATUS (E/S) PIN
Shutdown Input Mode
VE/S HIGH (output enabled)
VE/S LOW (output disabled)
IE/S HIGH (output enabled)
IE/S LOW (output disabled)
Output Disable Time
Output Enable Time
Thermal Shutdown Status Output
Normal Operation
Thermally Shutdown
Junction Temperature, Shutdown
Reset from Shutdown
POWER SUPPLY
Specified Voltage
Operating Voltage Range
Quiescent Current
Quiescent Current, Shutdown Mode
TEMPERATURE RANGE
Specified Range
Operating Range
Storage Range
Thermal Resistance, θJC
7-Lead DDPAK, 7-Lead TO-220
7-Lead DDPAK, 7-Lead TO-220
Thermal Resistance, θJA
7-Lead DDPAK, 7-Lead TO-220
E/S Pin Open or Forced HIGH
E/S Pin Forced LOW
E/S Pin HIGH
E/S Pin LOW
(V–) +2.4
Sourcing 20µA
Sinking 5µA, TJ > 160°C
(V–) +2.4
(V–) +0.8
–60
–65
1
3
±4
ILIM Connected to V–, IO = 0
ILIM Connected to V–
(V–) +3.5
(V–) +0.35
+160
+140
±30
±10
±4
–40
–40
–55
(V–) +0.8
V
V
µA
µA
µs
µs
V
V
°C
°C
±30
±15
V
V
mA
mA
+85
+125
+125
°C
°C
°C
f > 50Hz
dc
2
3
°C/W
°C/W
No Heat Sink
65
°C/W
NOTES: (1) High-speed test at TJ = +25°C. (2) Positive conventional current flows into the input terminals. (3) See Total Harmonic Distortion+Noise in the Typical
Characteristics section for additional power levels. (4) See Small-Signal Overshoot vs Load Capacitance in the Typical Characteristics section.
OPA547
SBOS056F
www.BDTIC.com/TI
www.ti.com
3
TYPICAL CHARACTERISTICS
At TCASE = +25°C, VS = ±30V, and E/S pin open, unless otherwise noted.
OPEN-LOOP GAIN AND PHASE
vs FREQUENCY
INPUT BIAS CURRENT vs TEMPERATURE
120
–160
RL = 50Ω
φ
60
–45
40
–90
20
–135
0
–180
Phase (°)
Gain (dB)
0
Input Bias Current (nA)
G
80
–120
10
100
1k
10k
100k
1M
VS = ±30V
–100
IB
–80
–60
–40
–20
–20
1
VS = ±5V
–140
100
0
–75
10M
–50
–25
0
25
Frequency (Hz)
CURRENT LIMIT vs TEMPERATURE
±600
RCL = 31.6kΩ
±300
RCL = 63.4kΩ
±200
150
–ILIM
RCL = 15.9kΩ
±500
±450
+400
RCL = 31.6kΩ
±350
±300
RCL = 63.4kΩ
±200
–50
–25
0
25
50
75
100
125
150
0
±5
±10
Temperature (°C)
±15
±20
±25
±30
Supply Voltage (V)
VOLTAGE NOISE DENSITY vs FREQUENCY
±12
Quiescent Current (mA)
400
Voltage Noise (nV/√Hz)
125
+ILIM
±250
±100
–75
100
±550
Current Limit (mA)
Current Limit (mA)
±400
75
CURRENT LIMIT vs SUPPLY VOLTAGE
±600
RCL = 15.9kΩ
±500
50
Temperature (°C)
300
200
100
QUIESCENT CURRENT vs TEMPERATURE
VS = ±30V
IQ
±10
±8
VS = ±5V
±6
VS = ±30V
IQ Shutdown
±4
VS = ±5V
±2
–75
0
1
10
100
1k
10k
100k
1M
4
–50
–25
0
25
50
75
100
125
150
Temperature (°C)
Frequency (Hz)
www.BDTIC.com/TI
www.ti.com
OPA547
SBOS056F
TYPICAL CHARACTERISTICS (Cont.)
At TCASE = +25°C, VS = ±30V, and E/S pin open, unless otherwise noted.
POWER SUPPLY REJECTION
vs FREQUENCY
COMMON-MODE REJECTION vs FREQUENCY
100
120
90
100
+PSRR
80
70
PSR (dB)
60
50
60
40
–PSRR
40
20
30
20
0
10
100
1k
10k
100k
1M
1
10
100
Frequency (Hz)
100k
1M
120
105
AOL
40
115
100
G = +1
3
CMRR (dB)
Overshoot (%)
10k
OPEN-LOOP GAIN, COMMON-MODE REJECTION,
AND POWER SUPPLY REJECTION vs TEMPERATURE
SMALL-SIGNAL OVERSHOOT
vs LOAD CAPACITANCE
50
1k
Frequency (Hz)
G = –1
20
CMRR
100
95
PSRR
95
90
10
85
–75
0
2k
4k
6k
8k
10k
12k
14k
16k
18k
75
100
125
90
150
10k
20k
0.1
7
6
SR–
1W
0.01
THD+N (%)
6.5
0.5
0.1W
6.25W
0.001
5.5
–25
0
25
50
75
100
125
5
150
0.0001
Temperature (°C)
SBOS056F
50
RL = 50Ω
G = +3
GBW
SR+
OPA547
25
TOTAL HARMONIC DISTORTION+NOISE
vs FREQUENCY
7.5
–50
0
GAIN-BANDWIDTH PRODUCT AND
SLEW RATE vs TEMPERATURE
0.75
0
–75
–25
Temperature (°C)
1
0.25
–50
Load Capacitance (pF)
1.25
Gain-Bandwidth Product (MHz)
20k
Slew Rate (V/µs)
0
20
100
1k
Frequency (Hz)
www.BDTIC.com/TI
www.ti.com
5
PSRR, AOL (dB)
CMR (dB)
80
TYPICAL CHARACTERISTICS (Cont.)
At TCASE = +25°C, VS = ±30V, and E/S pin open, unless otherwise noted.
OUTPUT VOLTAGE SWING vs TEMPERATURE
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
2.5
3
IO = +500mA
IO = +100mA
2
VSUPPLY – VOUT (V)
VSUPPLY– VOUT (V)
2.5
(V+) –VO
1.5
1
(V–) –VO
0.5
1.5
IO = –500mA
1
0.5
IO = –100mA
0
0
100
200
300
400
500
0
–75
600
–50
–25
0
25
50
75
Temperature (°C)
MAXIMUM OUTPUT VOLTAGE SWING
vs FREQUENCY
OUTPUT LEAKAGE CURRENT
vs APPLIED OUTPUT VOLTAGE
Leakage Current (mA)
15
10
0.5
RCL = 31.6kΩ
RCL = ∞
0
RCL = 0
–0.5
Output Disabled
VE/S < (V–) + 0.8V
5
–1
–40
0
1k
10k
100k
1M
–30
–20
–10
0
10
Frequency (Hz)
Output Voltage (V)
OFFSET VOLTAGE
PRODUCTION DISTRIBUTION
OFFSET VOLTAGE DRIFT
PRODUCTION DISTRIBUTION
20
25
Typical production
distribution of
packaged units.
Percent of Amplifiers (%)
Percent of Amplifiers (%)
150
RL = 10Ω
VS = ±30V
20
16
125
1
Maximum Output
Voltage Without
Slew Rate Induced
Distortion
25
18
100
Output Current (mA)
30
Output Voltage (Vp)
2
14
12
10
8
6
4
20
30
Typical production
distribution of
packaged units.
20
15
10
5
2
0
0
–5
–4
–3
–2
–1
0
1
2
3
4
0
5
10 15 20 25 30 35 40 45 50 55 60 65 70
Offset Voltage Drift (µV/°C)
Offset Voltage (mV)
6
5
www.BDTIC.com/TI
www.ti.com
OPA547
SBOS056F
TYPICAL CHARACTERISTICS (Cont.)
At TCASE = +25°C, VS = ±35V, and E/S pin open, unless otherwise noted.
SMALL SIGNAL STEP RESPONSE
G = 3, CL = 1000pF
50mV/div
50mV/div
SMALL SIGNAL STEP RESPONSE
G = 1, CL = 1000pF
2µs/div
2µs/div
10V/div
LARGE SIGNAL STEP RESPONSE
G = 3, CL = 100pF, RL = 50Ω
5µs/div
OPA547
SBOS056F
www.BDTIC.com/TI
www.ti.com
7
APPLICATIONS INFORMATION
Figure 1 shows the OPA547 connected as a basic noninverting
amplifier. The OPA547 can be used in virtually any op amp
configuration.
Power-supply terminals should be bypassed with low series
impedance capacitors. The technique shown, using a ceramic and tantalum type in parallel, is recommended. Powersupply wiring should have low series impedance.
V+
10µF
+
G = 1+
0.1µF(2)
R1
2
VIN
R2
R1
OPA547
6
3
1
ILIM(1)
4
(5000)(4.75)
– 31.6kΩ
ILIM
(1)
The low-level control signal (0µA to 150µA) also allows the
current limit to be digitally controlled with a current-out or
voltage-out DAC reference to V– according to the equations
given in Figure 3.
SAFE OPERATING AREA
E/S
7
R CL =
Figure 3 shows a simplified schematic of the internal circuitry
used to set the current limit. Leaving the ILIM pin open
programs the output current to zero, while connecting ILIM
directly to V– programs the maximum output current limit,
typically 750mA.
R2
5
With the OPA547, the simplest method for adjusting the
current limit uses a resistor or potentiometer connected
between the ILIM pin and V– according to the Equation 1:
Stress on the output transistors is determined both by the
output current and by the output voltage across the conducting output transistor, VS – VO. The power dissipated by the
output transistor is equal to the product of the output current
and the voltage across the conducting transistor, VS – VO.
The Safe Operating Area (SOA curve, Figure 2) shows the
permissible range of voltage and current.
VO
ZL
0.1µF(2)
10µF
+
V–
SAFE OPERATING AREA
1k
Output Current (mA)
NOTES: (1) ILIM connected to V– gives the maximum
current limit, 750mA (peak). (2) Connect 0.1µF capacitors
directly to package power-supply pins.
FIGURE 1. Basic Circuit Connections.
POWER SUPPLIES
The OPA547 operates from single (+8V to +60V) or dual
(±4V to ±30V) supplies with excellent performance. Most
behavior remains unchanged throughout the full operating
voltage range. Parameters which vary significantly with operating voltage are shown in the typical characteristic curves.
Some applications do not require equal positive and negative
output voltage swing. Power-supply voltages do not need to
be equal. The OPA547 can operate with as little as 8V
between the supplies and with up to 60V between the
supplies. For example, the positive supply could be set to
55V with the negative supply at –5V, or vice-versa.
ADJUSTABLE CURRENT LIMIT
The OPA547 features an accurate, user-selected current
limit. Current limit is set from 0mA to 750mA by controlling
the input to the ILIM pin. Unlike other designs which use a
power resistor in series with the output current path, the
OPA547 senses the load indirectly. This allows the current
limit to be set with a 0µA to 150µA control signal. In contrast,
other designs require a limiting resistor to handle the full
output current (750mA in this case).
8
Current-Limited
TC = 25°C
Output current may
be limited to less
than 500mA—see text.
100
TC = 85°C
TC = 125°C
Pulse Operation Only (<50% Duty-Cycle)
10
1
2
5
10
20
50
100
VS – VO (V)
FIGURE 2. Safe Operating Area.
The safe output current decreases as VS – VO increases.
Output short-circuits are a very demanding case for SOA. A
short-circuit to ground forces the full power-supply voltage
(V+ or V–) across the conducting transistor. With TC = 25°C
the maximum output current of 500mA can be achieved
under most conditions. Increasing the case temperature
reduces the safe output current that can be tolerated without
activating the thermal shutdown circuit of the OPA547. For
further insight on SOA, consult Application Bulletin SBOA022.
POWER DISSIPATION
Power dissipation depends on power supply, signal, and load
conditions. For dc signals, power dissipation is equal to the
product of output current times the voltage across the con-
www.BDTIC.com/TI
www.ti.com
OPA547
SBOS056F
ducting output transistor. Power dissipation can be minimized by using the lowest possible power-supply voltage
necessary to assure the required output voltage swing.
For resistive loads, the maximum power dissipation occurs at
a dc output voltage of one-half the power-supply voltage.
Dissipation with ac signals is lower. Application Bulletin
SBOA022 explains how to calculate or measure power
dissipation with unusual signals and loads.
HEAT SINKING
Most applications require a heat sink to assure that the
maximum junction temperature (150°C) is not exceeded. The
heat sink required depends on the power dissipated and on
ambient conditions. Consult Application Bulletin SBOA021 for
information on determining heat sink requirements. The internal protection circuitry was designed to protect against overload conditions. It does not activate until the junction temperature reaches approximately 160°C and was not intended to
replace proper heat sinking. Continuously running the OPA547
into thermal shutdown will degrade reliability.
The tab of the DDPAK surface-mount version should be
soldered to a circuit board copper area for good heat dissipation. Figure 4 shows typical thermal resistance from junction to ambient as a function of the copper area.
DAC METHOD (Current or Voltage)
RESISTOR METHOD
VO
G = 5000
G = 5000
31.6kΩ
4.75V
3
RCL
4
D/A
0.01µF
(optional, for noisy
environments)
4
V–
V–
RCL =
31.6kΩ
4.75V
3
VO
5000 (4.75V)
ILIM
IDAC = ILIM /5000
– 31.6kΩ
VDAC = (V–) + 4.75V – (31.6kΩ) (ILIM)/5000
OPA547 CURRENT LIMIT: 0mA to 750mA
DESIRED
CURRENT LIMIT
RESISTOR(1)
(RCL)
CURRENT DAC
(IDAC)
VOLTAGE DAC
(VDAC)
0mA
100mA
375mA
500mA
750mA
ILIM Open
205kΩ
31.6kΩ
15.8kΩ
ILIM Shorted to V–
0µA
20µA
75µA
100µA
150µA
(V–) + 4.75V
(V–) + 4.12V
(V–) + 2.38V
(V–) + 1.59V
(V–) + 0.01V
NOTE: (1) Resistors are nearest standard 1% values.
FIGURE 3. Adjustable Current Limit.
THERMAL RESISTANCE vs
CIRCUIT BOARD COPPER AREA
Circuit Board Copper Area
Thermal Resistance, θJA (°C/W)
50
OPA547F
Surface-Mount Package
1oz copper
40
30
20
10
OPA547
Surface-Mount Package
0
0
1
2
3
4
5
Copper Area (inches2)
FIGURE 4. Thermal Resistance versus Circuit Board Copper Area.
OPA547
SBOS056F
www.BDTIC.com/TI
www.ti.com
9
THERMAL PROTECTION
V+
The OPA547 has thermal shutdown that protects the amplifier from damage. Activation of the thermal shutdown circuit
during normal operation is an indication of excessive power
dissipation or an inadequate heat sink. Depending on load
and signal conditions, the thermal protection circuit may
cycle on and off. This limits the dissipation of the amplifier but
may have an undesirable effect on the load.
5V
OPA547
E/S
1
6
5
(1)
The thermal protection activates at a junction temperature of
approximately 160°C. However, for reliable operation, junction temperature should be limited to 150°C. To estimate the
margin of safety in a complete design (including heat sink),
increase the ambient temperature until the thermal protection
is activated. Use worst-case load and signal conditions. For
good reliability, the thermal protection should trigger more
than 35°C above the maximum expected ambient condition of
the application. This produces a junction temperature of
125°C at the maximum expected ambient condition.
HCT or TTL In
1
4
4N38
Optocoupler
V–
NOTE: (1) Optional—may be required to limit leakage
current of optocoupler at high temperatures.
FIGURE 6. Output Disable with Dual Supplies.
Thermal Shutdown Status
ENABLE/STATUS (E/S) PIN
The Enable/Status pin provides two functions: forcing this pin
low disables the output stage, or E/S can be monitored to
determine if the OPA547 is in thermal shutdown. One or both
of these functions can be utilized on the same device using
single or dual supplies. For normal operation (output enabled), the E/S pin can be left open or pulled high (at least
+2.4V above the negative rail).
Output Disable
A unique feature of the OPA547 is its output disable capability. This function not only conserves power during idle periods (quiescent current drops to approximately 4mA), but also
allows multiplexing in low frequency (f<10kHz), multichannel
applications. Signals that are greater than 10kHz may cause
leakage current to increase in devices that are shutdown.
Figure 15 shows the two OPA547s in a switched amplifier
configuration. The on/off state of the two amplifiers is controlled by the voltage on the E/S pin.
To disable the output, the E/S pin is pulled low, no greater than
0.8V above the negative rail. Typically the output is shutdown
in 1µs. Figure 5 provides an example of how to implement this
function using a single supply. Figure 6 gives a circuit for dualsupply applications. To return the output to an enabled state,
the E/S pin should be disconnected (open) or pulled to at least
(V–) + 2.4V. It should be noted that pulling the E/S pin high
(output enabled) does not disable internal thermal shutdown.
Internal thermal shutdown circuitry shuts down the output when
the die temperature reaches approximately 160°C, resetting
when the die has cooled to 140°C. The E/S pin can be
monitored to determine if shutdown has occurred. During
normal operation the voltage on the E/S pin is typically 3.5V
above the negative rail. Once shutdown has occurred this
voltage drops to approximately 350mV above the negative rail.
Figure 7 gives an example of monitoring shutdown in a
single-supply application. Figure 8 provides a circuit for dual
supplies. External logic circuitry or an LED could be used to
indicate if the output has been thermally shutdown, see
Figure 13.
V+
5V
OPA547
2.49kΩ
E/S
TTL
V–
Zetex
ZVN3310
OR
HCT
FIGURE 7. Thermal Shutdown Status with a Single Supply.
5V
V+
V+
1kΩ
OPA547
2N3906
E/S
OPA547
22kΩ
E/S
470Ω
Zetex
ZVN3310
V–
CMOS or TTL
V–
www.BDTIC.com/TI
FIGURE 5. Output Disable with a Single Supply.
10
FIGURE 8. Thermal Shutdown Status with Dual Supplies.
www.ti.com
OPA547
SBOS056F
Output Disable and Thermal Shutdown Status
OUTPUT PROTECTION
As mentioned earlier, the OPA547’s output can be disabled
and the disable status can be monitored simultaneously.
Figures 9 and 10 provide examples using a single supply and
dual supplies, respectively.
Reactive and EMF-generating loads can return load current to the amplifier, causing the output voltage to exceed
the power-supply voltage. This damaging condition can be
avoided with clamp diodes from the output terminal to the
power supplies, as shown in Figure 11. Schottkey rectifier
diodes with a 1A or greater continuous rating are recommended.
V+
OPA547
E/S
V+
V–
Open Drain
(Output Disable)
HCT
(Thermal Status
Shutdown)
R1
5kΩ
R2
20kΩ
G=–
R2
= –4
R1
VIN
FIGURE 9. Output Disable and Thermal Shutdown Status with
a Single Supply.
D1
OPA547
OUTPUT STAGE COMPENSATION
3Ω
(Carbon) Motor
D2
The complex load impedances common in power op amp
applications can cause output stage instability. For normal
operation output compensation circuitry is not typically required. However, if the OPA547 is intended to be driven into
current limit, a R/C network may be required. Figure 11
shows an output series R/C compensation (snubber) network (3Ω in series with 0.01µF) which generally provides
excellent stability. Some variations in circuit values may be
required with certain loads.
0.01µF
V–
D1, D2 : International Rectifier 11DQ06.
FIGURE 11. Motor Drive Circuit.
V+
5V
1
6
5V
OPA547
E/S
5
7.5kΩ
1W
1
6
2
(1)
Zetex
ZVN3310
5
TTL Out
4
4N38
Optocoupler
HCT or TTL In
2
4
4N38
Optocoupler
V–
NOTE: (1) Optional—may be required to limit leakage
current of optocoupler at high temperatures.
FIGURE 10. Output Disable and Thermal Shutdown Status with Dual Supplies.
OPA547
SBOS056F
www.BDTIC.com/TI
www.ti.com
11
VOLTAGE SOURCE APPLICATION
PROGRAMMABLE POWER SUPPLY
Figure 12 illustrates how to use the OPA547 to provide an
accurate voltage source with only three external resistors.
First, the current limit resistor, RCL, is chosen according to
the desired output current. The resulting voltage at the ILIM
pin is constant and stable over temperature. This voltage,
VCL, is connected to the noninverting input of the op amp and
used as a voltage reference, thus eliminating the need for an
external reference. The feedback resistors are selected to
gain VCL to the desired output voltage level.
A programmable power supply can easily be built using the
OPA547. Both the output voltage and output current are
user-controlled. Figure 13 shows a circuit using potentiometers to adjust the output voltage and current while Figure 14
uses DACs. An LED tied to the E/S pin through a logic gate
indicates if the OPA547 is in thermal shutdown.
R1
R2
V+
VO = VCL (1 + R2/R1)
4.75V
31.6kΩ
IO =
VCL
ILIM
For Example:
V–
RCL
0.01µF
(Optional, for noisy
environments)
If ILIM = 375mA, RCL = 31.6kΩ
VCL =
31.6kΩ • 4.75V
(31.6kΩ + 31.6kΩ)
Desired VO = 19V, G =
5000 (4.75V)
31.6kΩ + RCL
= 2.375V
19
2.375
Uses voltage developed at ILIM pin
as a moderately accurate reference
voltage.
=8
R1 = 1kΩ and R2 = 7kΩ
FIGURE 12. Voltage Source.
1kΩ
9kΩ
G=1+
+5V
9kΩ
= 10
1kΩ
+30V
14.7kΩ
5
2
V+
6
Output
Adjust
0.8V to 2.5V
VO = 0.8V to 25V(1)
OPA547
1
4
3
7 E/S
74HCT04
ILIM
R ≥ 250Ω
4.7kΩ
V–
+5V
0V to 4.75V
Thermal
Shutdown Status
(LED)
1kΩ
Current
Limit
Adjust
20kΩ
0.01µF(2)
NOTES: (1) For VO = 0V, V– = –1V.
(2) Optional: Improves noise
immunity.
FIGURE 13. Resistor-Controlled Programmable Power Supply.
12
www.BDTIC.com/TI
www.ti.com
OPA547
SBOS056F
1kΩ
9kΩ
+10V
OUTPUT ADJUST
VREF
+30V
G = 10
+5V
VREF A
+5V
RFB A
1/2
OPA2336
IOUT A
1/2 DAC7800/1/2(3)
VO = 0.8 to 25V(1)
OPA547
10pF
74HCT04
E/S
DAC A
AGND A
ILIM
IO = 0 to 750mA
R ≥ 250Ω
V–
Thermal
Shutdown Status
(LED)
VREF B
RFB B
10pF
1/2
OPA2336
IOUT B
1/2 DAC7800/1/2(3)
DAC B
0.01µF(2)
DGND
AGND B
CURRENT LIMIT ADJUST
NOTES: (1) For VO = 0V, V– = –1V. (2) Optional, improves noise immunity. (3) Chose DAC780X based on
digital interface: DAC7800—12-bit interface, DAC7801—8-bit interface + 4 bits, DAC7802—serial interface.
(4) Can use OPA2237, IO = 100mA to 750mA.
FIGURE 14. Digitally-Controlled Programmable Power Supply.
R1
R2
VIN1
OPA547
ILIM
AMP1
E/S
RC2
RC1
R3
VE/S
R4
Close for high current
(Could be open drain
output of a logic gate).
VO
VIN2
AMP2
V–
E/S
FIGURE 16. Multiple Current Limit Values.
VE/S > (V–) +2.4V: Amp 1 is on, Amp 2 if off
VO = –VIN1
R2
( )
R1
VE/S < (V–) +2.4V: Amp 2 is on, Amp 1 if off
VO = –VIN2
R4
( )
R3
FIGURE 15. Swap Amplifier.
OPA547
SBOS056F
www.BDTIC.com/TI
www.ti.com
13
PACKAGE OPTION ADDENDUM
www.ti.com
14-Jul-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
Lead/Ball Finish
MSL Peak Temp (3)
OPA547F
OBSOLETE
DDPAK
KTW
7
TBD
Call TI
Call TI
OPA547F/500
ACTIVE
DDPAK
KTW
7
500
Green (RoHS &
no Sb/Br)
CU SN
Level-2-260C-1 YEAR
OPA547F/500G3
ACTIVE
DDPAK
KTW
7
500
Green (RoHS &
no Sb/Br)
CU SN
Level-2-260C-1 YEAR
OPA547FKTWT
ACTIVE
DDPAK
KTW
7
50
Green (RoHS &
no Sb/Br)
CU SN
Level-2-260C-1 YEAR
OPA547FKTWTG3
ACTIVE
DDPAK
KTW
7
50
Green (RoHS &
no Sb/Br)
CU SN
Level-2-260C-1 YEAR
OPA547T
ACTIVE
TO-220
KVT
7
50
Green (RoHS &
no Sb/Br)
CU SN
N / A for Pkg Type
OPA547T-1
ACTIVE
TO-220
KC
7
50
Green (RoHS &
no Sb/Br)
CU SN
N / A for Pkg Type
OPA547T-1G3
ACTIVE
TO-220
KC
7
50
Green (RoHS &
no Sb/Br)
CU SN
N / A for Pkg Type
OPA547TG3
ACTIVE
TO-220
KVT
7
50
Green (RoHS &
no Sb/Br)
CU SN
N / A for Pkg Type
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
www.BDTIC.com/TI
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
OPA547F/500
DDPAK
KTW
7
500
330.0
24.4
10.6
15.6
4.9
16.0
24.0
Q2
OPA547FKTWT
DDPAK
KTW
7
50
330.0
24.4
10.6
15.6
4.9
16.0
24.0
Q2
www.BDTIC.com/TI
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
OPA547F/500
DDPAK
KTW
7
500
346.0
346.0
41.0
OPA547FKTWT
DDPAK
KTW
7
50
346.0
346.0
41.0
www.BDTIC.com/TI
Pack Materials-Page 2
MECHANICAL DATA
MPSF015 – AUGUST 2001
KTW (R-PSFM-G7)
PLASTIC FLANGE-MOUNT
0.410 (10,41)
0.385 (9,78)
0.304 (7,72)
–A–
0.006
–B–
0.303 (7,70)
0.297 (7,54)
0.0625 (1,587) H
0.055 (1,40)
0.0585 (1,485)
0.300 (7,62)
0.064 (1,63)
0.045 (1,14)
0.252 (6,40)
0.056 (1,42)
0.187 (4,75)
0.370 (9,40)
0.179 (4,55)
0.330 (8,38)
H
0.296 (7,52)
A
0.605 (15,37)
0.595 (15,11)
0.012 (0,305)
C
0.000 (0,00)
0.019 (0,48)
0.104 (2,64)
0.096 (2,44)
H
0.017 (0,43)
0.050 (1,27)
C
C
F
0.034 (0,86)
0.022 (0,57)
0.010 (0,25) M
B
0.026 (0,66)
0.014 (0,36)
0°~3°
AM C M
0.183 (4,65)
0.170 (4,32)
4201284/A 08/01
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Lead width and height dimensions apply to the
plated lead.
D. Leads are not allowed above the Datum B.
E. Stand–off height is measured from lead tip
with reference to Datum B.
F. Lead width dimension does not include dambar
protrusion. Allowable dambar protrusion shall not
cause the lead width to exceed the maximum
dimension by more than 0.003”.
G. Cross–hatch indicates exposed metal surface.
H. Falls within JEDEC MO–169 with the exception
of the dimensions indicated.
www.BDTIC.com/TI
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MSOT010 – OCTOBER 1994
KC (R-PSFM-T7)
PLASTIC FLANGE-MOUNT PACKAGE
0.156 (3,96)
0.146 (3,71)
0.420 (10,67)
0.380 (9,65)
DIA
0.113 (2,87)
0.103 (2,62)
0.185 (4,70)
0.175 (4,46)
0.055 (1,40)
0.045 (1,14)
0.147 (3,73)
0.137 (3,48)
0.335 (8,51)
0.325 (8,25)
1.020 (25,91)
1.000 (25,40)
1
7
0.125 (3,18)
(see Note C)
0.030 (0,76)
0.026 (0,66)
0.010 (0,25) M
0.050 (1,27)
0.300 (7,62)
0.122 (3,10)
0.102 (2,59)
0.025 (0,64)
0.012 (0,30)
4040251 / B 01/95
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
Lead dimensions are not controlled within this area.
All lead dimensions apply before solder dip.
The center lead is in electrical contact with the mounting tab.
www.BDTIC.com/TI
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
www.BDTIC.com/TI
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated
www.BDTIC.com/TI