* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download DN221 - SOT-23 Micropower, Rail to Rail Op Amps Operate with Inputs Above the Positive Supply
Flip-flop (electronics) wikipedia , lookup
Radio transmitter design wikipedia , lookup
Josephson voltage standard wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Analog-to-digital converter wikipedia , lookup
Power MOSFET wikipedia , lookup
Integrating ADC wikipedia , lookup
Negative-feedback amplifier wikipedia , lookup
Two-port network wikipedia , lookup
Surge protector wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Current source wikipedia , lookup
Transistor–transistor logic wikipedia , lookup
Power electronics wikipedia , lookup
Valve audio amplifier technical specification wikipedia , lookup
Wilson current mirror wikipedia , lookup
Voltage regulator wikipedia , lookup
Valve RF amplifier wikipedia , lookup
Schmitt trigger wikipedia , lookup
Operational amplifier wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Current mirror wikipedia , lookup
advertisement SOT-23 Micropower, Rail-to-Rail Op Amps Operate with Inputs Above the Positive Supply – Design Note 221 Raj Ramchandani Introduction The only SOT-23 op amps featuring Over-The-TopTM operation—the ability to operate with either or both inputs above the positive rail—are the 55µA LT®1782 and the 300µA LT1783. This feature is important in many currentsensing applications, where the inputs are required to operate at or above the supply. The wide supply voltage range, from 2.7V to 18V, gives the LT1782/LT1783 broad appeal as general purpose amplifiers, while the guaranteed offset voltage of 950µV over temperature is the lowest of any SOT-23 op amp. There is even a shutdown feature for ultralow supply current applications. Table 1. LT1782/LT1783 SOT-23 Guaranteed Performance, VS = 3V/0V or 5V/0V, TA = 25°C Tough General Purpose Op Amps The LT1782/LT1783 SOT-23 op amps are ideal for general purpose applications that demand excellent performance. These SOT-23 op amps are specified at input common mode voltages as high as 18V, independent of the supply voltage, making them ideal for applications with a wide input range requirement and/or unusual input conditions. In applications that require more bandwidth than the 200kHz LT1782, the LT1783’s six-fold increase in supply current gives it six times more bandwidth and slew rate. The parts are available in two pinouts, a 6-lead version with a shutdown feature that reduces supply current to only 5µA, and a standard pinout 5-lead version. Table 1 summarizes the performance of these new op amps. –18V OK! VCC LT1782 LT1783 LT1783 2.7V to 18V 2.7V to 18V Supply Current (Max) 55µA 300µA Input Offset Voltage (Max) 800µV 800µV Input Bias Current (Max) 15nA 80nA Input Bias Current, V+ = 0V (Typ) 0.1nA 0.1nA 2nA 8nA 200V/mV 200V/mV PSRR (Min) 90dB 90dB CMRR (Min) 90dB 90dB 0V to 18V 0V to 18V Supply Voltage Range Input Offset Current (Max) Open-Loop Gain, RL = 10k (Min) Common Mode Range – V –) 8mV 8mV Output Swing High, (V + – VO) 90mV 90mV Slew Rate (Typ) 0.07V/µs 0.42V/µs Gain Bandwidth Product (Typ) 200kHz 1.25MHz Output Swing Low, (VO Tough Op Amps The LT1782/LT1783 are tough op amps that can be exposed to a variety of extreme conditions without being damaged (Figure 1). The amplifiers have reverse-battery protection up to 18V. The input pin voltage can extend to 10V below V – or 24V above V – without damaging the , LTC and LT are registered trademarks of Linear Technology Corporation. Over-The-Top is a trademark of Linear Technology Corporation. 5V LT1782 LT1783 24V LT1782 5V OK! 18V + OK! LT1782 LT1783 + 5V LT1782 LT1783 10V + OK! PARAMETER DN221 F01 Figure 1. Tough Op Amps 01/00/221 www.BDTIC.com/Linear device. The maximum input differential voltage is 18V, regardless of the supply voltage. All of these features combine to make the LT1782/LT1783 “one tough SOT-23.” Read All of the Specs Common factors that keep most SOT-23 parts from being general purpose amplifiers include low supply voltage range, high input offset voltage, low open-loop voltage gain and poor output stage performance. The LT1782/LT1783 amplifiers operate on all single and split supplies with a total voltage of 2.7V to 18V. They are stable with capacitive loads up to 500pF under all load conditions. The minimum output current is ±18mA and the unloaded output swing is guaranteed within 8mV of ground and 90mV of the positive rail. A common problem encountered with other op amps in many applications is that as the output approaches the rail or ground, the gain degrades. The data sheet typically claims the output can swing to within a few millivolts of the rail, but the input overdrive required to achieve this can be quite high. This not the case with the LT1782/ LT1783; a few millivolts of input overdrive is enough to swing the outputs to their guaranteed value. Figure 2 shows the typical output saturation voltage vs input overdrive. Over-The-Top Applications The circuit of Figure 3 uses the Over-the-Top capabilities of the LT1783. The 0.2Ω resistor senses the load current while the op amp and NPN transistor form a closed loop, making the collector current of Q1 proportional to the load current. The 2k load resistor converts the current into a voltage. The positive supply rail, VBAT, is not limited to the 5V supply of the op amp and could be as high as 18V. The LT1783 draws no current through the inputs when it is powered down, extending the battery life. The circuit of Figure 4 uses the LT1782 in conjunction with the LT1634 micropower shunt reference. The supply current of the op amp also biases the reference. The drop across resistor R1 is fixed at 1.25V generating an output current equal to 1.25V/R1. Notice that noninverting input is tied to the VCC pin of the op amp. VBAT 200Ω 5V SHDN + 0.2Ω LT1783 200Ω LOAD – ILOAD Q1 2N3904 VOUT = 2Ω • ILOAD 0V TO 4.3V 2k DN221 F03 OUTPUT SATURATION VOLTAGE (mV) 100 Figure 3. Positive Supply Rail Current Sense OUTPUT HIGH VCC 10 LT1634-1.25 R1 SHDN OUTPUT LOW + LT1782 1 0 10 20 30 40 50 INPUT OVERDRIVE (mV) 60 2N3906 – IOUT = 1.25V R1 DN221 F04 DN221 F02 Figure 2. Output Saturation Voltage vs Input Overdrive Data Sheet Download http://www.linear-tech.com/go/dnLT1782 http://www.linear-tech.com/go/dnLT1783 Linear Technology Corporation Figure 4. Current Source For literature on our Op Amps, call 1-800-4-LINEAR. For applications help, call (408) 432-1900, Ext. 2456 dn221f LT/TP 0100 370K • PRINTED IN THE USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 www.BDTIC.com/Linear (408)432-1900 ● FAX: (408) 434-0507 ● www.linear-tech.com LINEAR TECHNOLOGY CORPORATION 2000