Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download KCU105_Power_Controllers_Reprogramming_Steps
Document related concepts
Electric power system wikipedia , lookup
Voltage optimisation wikipedia , lookup
History of electric power transmission wikipedia , lookup
Alternating current wikipedia , lookup
Opto-isolator wikipedia , lookup
Power over Ethernet wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Transcript
KCU105 Power Bus Reprogramming © Copyright 2015 Xilinx . Contents Caution! Xilinx KCU105 Board Hardware & Software Requirements Setup Maxim PowerTool software Tutorial Page 2 © Copyright 2015 Xilinx . Caution! The Maxim PowerTool software used in this presentation can adjust the power supply outputs on the KCU105 If used improperly, it may seriously damage your KCU105 Before making any adjustments not specifically covered in this presentation: – Understand the power requirements for Kintex UltraScale Devices – Understand the consequences of the change you are making – Understand that the PMBus devices can ONLY be programmed 4 times Page 3 © Copyright 2015 Xilinx . Xilinx KCU105 Board Page 4 © Copyright 2015 Xilinx . Hardware Requirements Maxim MAXPOWERTOOL002# USB-to-PMBus interface dongle – Maxim Part Number: MAXPOWERTOOL002# Page 5 © Copyright 2015 Xilinx . Software Requirements Maxim Digital Power Tool – Maxim File name: MaximDigitalPowerTool_V1.08.05.exe (version subject to change) – Download: Latest Release at http://www.maximintegrated.com/en/design/tools/applications/evkitsoftware/index.mvp?id=1183/ Page 6 © Copyright 2015 Xilinx . Software Setup Install the Maxim Digital Power Tool Page 7 © Copyright 2015 Xilinx . Connect Maxim Dongle On the Maxim Dongle – Connect the Ribbon Cable – Connect the USB Cable Page 8 © Copyright 2015 Xilinx . Connect Maxim Dongle Connect the Ribbon Cable to the KCU105 – Red Stripe towards pin 1 – Insert the “A” end of the USB cable into a PC USB port (do not use a docking station or USB hub port) – Install J12 jumper to inhibit all FPGA rails – Turn on the KCU105 board Page 9 © Copyright 2015 Xilinx . Check Voltage Levels Using the Maxim PowerTool, check that you see the following (voltages inhibited): DS3 LED on the KCU105 will appear red Page 10 © Copyright 2015 Xilinx . Restoring Power Levels Unzip included file: FULL_KCU105_111313_r2_MAXIM_XML.zip Open MaximDigitalPower GUI Verify that all 10 power rails are listed in the GUI: – 0x0A – 0x0B – 0x0F – 0x11 – 0x12 – 0x14 – 0x15 – 0x16 – 0x18 – 0x1B Page 11 © Copyright 2015 Xilinx . Maxim PowerTool Expand the Maxim GUI so that you can see the “Load Configuration” button on the GUI Click “Load Configuration” and browse to where you have saved FULL_KCU105_111313_r2_MAXIM_XML.xml – load this file Page 12 © Copyright 2015 Xilinx . Maxim PowerTool Once the XML has been programmed in, the GUI will prompt you to say the controllers must be re-loaded You may need to click the “Search for Devices” button to refresh the controller information Page 13 © Copyright 2015 Xilinx . Maxim PowerTool From the Dashboard tab, click “Store User ALL” button IMPORTANT: Do not power off the board Verify that you only press STORE USER ALL once Page 14 © Copyright 2015 Xilinx . Maxim PowerTool Power off the KCU105 Remove jumper J12 Power on the KCU105 once more to verify If the Dashboard does not refresh automatically: – Click the “Search for Devices” button Verify that all Power Good LEDs in the top right corner of the KCU105 are on Verify that the FPGA power good LED is green Open the Maxim PowerTool GUI to verify the correct voltages on 12V (Input Voltage) and all FPGA rails (Output Voltage) Page 15 © Copyright 2015 Xilinx .
