Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Impact Wall LED INSTALLATION INSTRUCTIONS Sheet 1 of 2 3/3/10 IMPORTANT : READ BEFORE REMOVING FIXTURE FROM CARTON. RETAIN FOR FUTURE REFERENCE. GENERAL: Upon receipt of fixture thoroughly inspect for any freight damage, which should be brought to the attention of the delivery carrier. Compare the catalog description listed on the packing slip with the fixture label on the housing to be sure the correct merchandise has been received. SAFETY: This fixture must be wired in accordance with the National Electrical Code, National Electrical Safety Code and applicable local codes and ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under installation section. This fixture is not suitable for Hazardous or Classified Locations. This product must be installed in accordance with the applicable installation code by a person familiar with the construction IMI-723 and operation of the product and hazards involved. Consult a qualified electrician to ensure correct branch circuit conductor. WARNING: Risk of Fire/Electric Shock. If not qualified, consult an electrician. WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing. WARNING: Risk of burn. Disconnect power and allow fixture to cool before servicing. WARNING: Risk of personal injury—Fixture may become damaged and/or unstable if not installed properly. Tighten all fixture components to their recommended torque values. TOOLS REQUIRED: Allen Key (3/16"), Phillips screw driver, electrical wiring tools. NOTE: This lighting fixture is designed for outdoor lighting services, and should not be used in area of limited ventilation or in high ambient temperature enclosures. It must be stored in a dry location prior to installation. Do not expose lighting fixture to rain, dust or other environmental conditions prior to installation. Best results will be obtained if installed and maintained according to the following recommendations. NOTE: Care must be taken not to set lighting fixture down on optical lenses or lift the fixture in the lens area. NOTE: This instruction sheet is applicable for all shapes and colors of the IMPACT Wall Collection. The trapezoid shape is used for illustration. APPLICATION • Minimum 90ºC Supply Conductors when connections are made external to the unit • Rated for 40ºC (104ºF) ambient • Suitable for wet location • Wall mount luminaire only • Construction is suitable for down mount only • Must be mounted above grade at minimum 4 feet or higher FIG. 1 Mounting Orientation Down Mounting Plate (Secure to J-Box or Wall) Gasket on back Junction Box or Wall INSTALLATION (2) Allen Head Screws Mounting—FIG. 1 1. Remove the mounting plate from the fixture by loosening the two (2) set-screws. 2. Remove the protective paper from the supplied pressure sensitive adhesive backed gasket. 3. Align the gasket to the holes on the mounting plate and apply pressure to secure to the back of the mounting plate. 4. Mount the gasket applied mounting plate to the junction box or wall with the gasket away from the luminaire and secure to structure FIG. 1. 5. Slide the luminaire mounting bracket over the top lid of the mounting plate. These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative. NOTE: Specifications and dimensions subject to change without notice. Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 ADH091930 Impact Wall LED Sheet 2 of 2 INSTALLATION INSTRUCTIONS 3/3/10 IMI-723 IMPORTANT : READ BEFORE REMOVING FIXTURE FROM CARTON. RETAIN FOR FUTURE REFERENCE. 6. Tighten the two(2) set-screws to secure the luminaire to the mounting plate. Wiring—FIG. 2 1. The application notes, included within the unit, and instruction sheet indicate the proper minimum supply wire rating. 2. Supply wiring is accessible within the unit when the LightBARTM mounting plate is removed by unscrewing four (4) screws. 3. The luminaire comes standard wired for universal 120-277V driver supplied (347V when ordered). 4. Complete the connections per the diagram FIG. 2 and the NEC or Canadian standards using approved methods and devices. FIG. 2 L1 (Supply) L2 (Common) Ground DIMMING/BI-LEVEL SWITCHING—2L (IF EQUIPPED) For Bi-level switching, the input leads to the fixture will be independently labeled to indicate dimming preferences as appropriate (as defined by the order requirements). Two [2] Separate supply lines of line voltage, neutral and ground must be provided to the fixture to enable the bi-level switching functionality of the fixture. Wall MAINTENANCE NOTE: A regular maintenance schedule should be followed to retain optimal light output and thermal performance. Optical lens cleaning should be performed with a clean dry cloth to remove any dust or other contaminants. Additional cleaning can be performed with non-abrasive acrylic cleanser. NOTE: DO NOT USE GLASS CLEANERS. These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative. NOTE: Specifications and dimensions subject to change without notice. Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 ADH091930