Download Liquid crystals technology - School of Computer Science

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

X-ray crystallography wikipedia , lookup

Cocrystal wikipedia , lookup

Birefringence wikipedia , lookup

Crystal structure wikipedia , lookup

Crystallization wikipedia , lookup

Transcript
Liquid Crystals:
Properties and technology
CHM3T1
Lecture- 8
Dr. M. Manickam
School of Chemistry
The University of Birmingham
[email protected]
Out line of This Lecture
 Introduction
 Properties of liquid crystals
 Different types liquid crystal displays
 Fabrication and operation of liquid crystal displays
 Final comments
Learning Objectives
After completing this lecture you should have an understanding of, and be
able to demonstrate, the following terms, ideas and methods.
1. Understand how the liquid crystals interact with surfaces
2. Understand how the liquid crystals interact with light
3. Understand how the liquid crystals interact with electric fields
4. How do liquid crystals displays work?
5. How the Twisted Nematic Liquid Crystal Display work (TNLCDs)?
6. How the Super Twisted Nematic Crystal Display Work (STNLCDs)?
7. The difference between TN and STN Devices
8. How the Surface-Stabilised Ferroelectric Liquid Crystal Display Work
(SSFLCD)?
Anisotropic Liquid
An anisotropic liquid is a liquid, i.e. it has fluidity in much the same way
as solvent such as water or chloroform has.
However, unlike water or chloroform where there is no structural ordering
of the molecules in the liquid, molecules in anisotropic liquid are on
average structural order relative to each other along their molecular
axis.
Anisotropy
Moving plate
a: Fixed plate
Moving plate
b: Fixed plate
Moving plate
c: Fixed plate
Figure- 1
Diagram to represent a method of demonstrating in a liquid crystal
a; Director is pointing out of the page
b; Director is in the direction of the moving plate
c; Director points up or down
Anisotropy
An isotropic material is one whose properties do not change with
direction.
Both liquids and gases are isotropic.
However, liquid crystals and some solid e.g. quartz, are anisotropic.
Liquid crystals anisotropy is related to the alignment of their molecules
relative to each other.
A good way of illustrating this is to consider the action of sliding two
flat plates over one another after liquid crystals have been placed in
between them (Figure1)
The force necessary to move the top plate over the fixed plate is
approximately the same for cases (a) and (b) but is much higher for (c)
Alignment at Surfaces
Figure -2: Schematic to show a single alignment layer of liquid crystal molecules
a; parallel to a surface
Homotropical alignment
b; perpendicular to a surface
Heterotopical alignment
Alignment at Surfaces
The inherent tendency for liquid crystals to align is so sensitive that they can
readily be made to align with any surface.
Various methods of treating a glass surface can be used.
For example, by simply rubbing it in one direction with a piece of cloth or
preparing it with a surfactant, it is possible, to induce alignment of the director at
almost any angle to the surface.
Most important cases are when the alignment is parallel (Figure-2a) and
perpendicular (Figure- 2b) to the surface of the glass.
Figure- 2 shows the alignment of a single layer of liquid crystal molecules, this
will in turn align the molecules in the layer above for several micrometers.
This alignment is made use of in the technological applications of liquid crystals,
in particular parallel alignment is of importance in the twisted nematic display
which will be discussed latter.
Permanent Electric Dipole
Many liquid crystals molecules are composed of neutral atoms and not charged.
However, it is possible for the bonding between the atoms of a molecule to be
such that a permanent electric dipole is produced.
The result is that the molecule bears a positive charge at one end and a negative
charge at the other.
One example is a common calamitic liquid crystals template, the
alkoxycyanobiphenyls (Figure-3).
..
RO
C
Resonance structure of an
alkoxycyanobiphenyl,
producing a permanent
electric dipole
N
+
RO
C
N
Figure-3
-
Interaction with Electric Fields
If no electric field is present, the permanent electric dipole on the liquid crystal
molecules are not aligned, although the molecules themselves are aligned with
respect to one another.
When direct current is applied the molecule will orient themselves along the field
(Figure-4).
This property is unique to liquid crystals, in a liquid the fast, disordered motion
of the molecules prevents the same orientation from occurring, and in solids, the
bonding between molecules means they are unable to change their positions.
The principle features of liquid crystals enabling this interaction with electric
fields are their freedom of movement, like isotropic liquids, and their maintenance
of orientation order, like crystalline solids.
Figure-4
+ -+ - - +
+ - + - + - + - + - +
applying an
electric field
- - - - + + + + +
- - - - + + + + +
Diagram to illustrate the
effect of an applied electric
field on the alignment of
liquid crystal molecules.
Interaction with Light
Unpolarised light can be considered as being made up of electromagnetic waves
oscillating in different planes.
A polariser can be placed in front of an unpolarised light source, this allows
waves in only one plane through and polarises the light.
The plan-polarised light can then be completely blocked by a second polariser
fixed at right angles (i.e. crossed) to the first as shown in Figure-5
Figure- 5: Demonstration of the action of polarisers on unpolariserd light
Polariser 1
Polariser 2
Light
source
Polariser and Analyser
Figure : (a) When the polariser and analyser are in a parallel set up, their optical
axes allow light transmission;
(b) when the polariser and analyser are crossed, the
light from the polariser is absorbed by the analyser, resulting in dark condition.
Birefringence
Anisotropic materials produce different values for the index of refraction when the
light is linearly polarised along the x-axis and when it is polarised along the yaxis. This phenomenon is referred to as birefringence.
Due to the aligning abilities of liquid crystal molecules, it is possible to illustrate
their birefringence in a different manner (Figure- 6).
Different indices of refraction are produced when the liquid crystal molecules in a
sample are aligned at different angle relative to the incoming plane-polarised light.
It is birefringence that is responsible for the vivid colours observed in LCs when
viewed under an OPM
X-polarised light
Perpendicular to x-polarised light
c
v1
n1= c/v1
The back lines represent the alignment layers of the LCs
molecules
X-polarised light
Parallel to x-polarised light
v1
c
Figure-6: Diagram to show effect of liquid crystals aligned
n1= c/v1
Helical Pitch
The pitch is the distance for one full director rotation
If the molecules that form a liquid
crystals phase are chiral (lack of
inversion symmetry), then chiral phases
exist in place of certain non-chiral phases.
In calamitic liquid crystals, the nematic
phase is replaced by the chiral nematic
phase, in which the director rotates in
helical fashion about an axis perpendicular
to the director.
The pitch of a nematic phase is the
distance along the helix over which the
director rotates by 360o
Chiral Nematic Phase
The structure of the chiral nematic phase.
The views represent imaginary slices through
the structure and do not imply any type of
layered structure
LCs Displays
LCs have diverse applications, they are chiefly known for their extensive
exploitation in display application.
Liquid crystalline materials are used extensively in electro-optic (EO)
devices due to their anisotropic properties (mainly alignment in electric
field and birefringence) combined with the processability of the fluid state.
Therefore, LCs have been used in displays for more than thirty years starting
with the simple passive-matrix displays to the technologically advanced
multiplex active-matrix displays.
Fabrication of LCDs
Whatever type of liquid crystal display (LCD), Figure- 7 illustrates the elements
that are generally present.
The central unit is constituted by the LC film, sandwiched between lamellae of
functional elements as shown in Figure- and listed in Table-1
Figure-7: Scheme of the sequence of the most common parts used for the fabrication of
LCDs
Main Layers in LCDs
Table- 1. Main layers applied in LCDs.
The first layer is the one adjacent to the glass sheets and the last one is in direct
contact with the inner LC film
The quality of any LCD depends strongly upon the physical properties of the LC.
To achieve a high standard of performance it is essential to select the most
appropriate LC material according to the specific requirements of the desired
type of display.
Physical properties of calamitic
materials for displays
Consequently, in general LCs must satisfy characteristics such as the following:
 Liquid crystalline at room temperature and over the entire temperature
range of the display operation,
 Chemically, electrochemically and photochemically stable,
 High resistivity,
 Low rotational viscosity,
 Either low or high birefringence, depending upon the type of display,
 Permanent electric dipole, hence either a positive or negative dielectric
anisotropy
 However, it is impossible that these demands are satisfied by a single liquid
crystalline species alone. Therefore, formulations of LC mixtures are usually
employed in LCDs.
Twisted Nematic Displays (TNDs)
TNDs was invented by Schadt and Hefrich, and represented the first successful
application of LCs.
Together with the super twisted nematic displays (STNDs), the TNDs still
dominate the entire commercial production of displays.
The principle of the operation of these devices is based on the optical absorption
or variable birefringence effects of nematic LCs, subjected
to a switching electric field.
Operation Principles of Twisted Nematic
Displays
The nematic materials used in these devices are characterised by a positive
dielectric anisotropy, as a consequence of the presence of highly polar
terminal groups, resulting in the molecular dipole being oriented along the
molecular director and the long axis (Figure-8).
permanent dipole
= dipole
No permanent
dipole
C
N
R
R
N
RO
N
RO
C N
O
K
106
128
N
Figure-8: N-(4-ethoxybenzylidene)-4’-aminobenzonitrile is a typical example of
one of the first nematic liquid crystal used in TNDs, with positive dielectric anisotropy.
Twisted Nematic Displays (TNDs)
Twisted Nematic Display
Electrodes
Crossed Polarisers
Alignment Layers
Liquid CrystalEutectic Mixture
NO ELECTRIC FIELD 9a
light
Chiral Dopant
LIGHT TRANSMITTED
ELECTRIC FIELD 9b
Polarised light
Director n
LIGHT NOT
TRANSMITTED
Operation Principles of TNDs [off-state]
In these displays, the LC is positioned between two glass plates with parallel
(homogeneous) alignment of its molecular director with the glass walls.
However, the two glass plates twisted by 900 relative to each other (Figure- 9a)
In such a geometry the LC is forced to perform a 900 twist of the director from
plate to plate, resulting in a helical structure, whose chirality is controlled by
additional doping (~ 1%) with a chiral nematic material.
The distance between the plates, hence the thickness of the LC film, is typically 610µm, which corresponds to half of the helical pitch.
To complete the TND unit, a pair of crossed (900) polarisers is placed on the outer
side of the glass plates.
In the absence of an external electric field, when linearly polarised light enters the
device, the LC film acts as an optical wave guide rotating the polarisation of the
light by 900.
Thus, the light reaches the second polariser with its polarisation plane parallel to
the polariser axis and is transmitted. In this configuration the display appears
bright (off-state) (Figure -9a)
Operation Principles of TNDs [ on-state]
However, when an electric field (~ 2 V µm -1) is applied (on-state), the LC
molecules reorient in order to align the molecular director with the
external electric field, causing the helical arrangement to be
unwound.
As a consequence, the light passing through the LC film, is not guided
through 900, and is not able to pass through the second polariser
(Figure- 9b).
Upon removal of the electric field the LC molecules will relax back into
the initial twisted state, in a time dependant manner determined by
the rotational viscosity parameter.
In some displays, placing the polarisers parallel rather than
perpendicular to each other reverses the off- and on- state.
Twisted Nematic Display
Operation Principle of Supertwisted Nematic
Displays (STNDs)
In the TNDs the switching speeds are of the order of milliseconds, which is fast
enough for watches, calculators, and similar low information content
application.
However, for more sophisticated real-time devices, where the higher data transfer
rates demand faster response time than tens of milliseconds, they are not
suitable.
STNDs represent an improvement relative to the TNDs, and in fact this type is the
one used in more sophisticated applications such as video cameras, monitors,
and laptops displays.
The fabrication characteristic of the STNDs requires the LC material to perform a
rotation up to 2700.
This extra rotation allows the STNDs to have a steeper voltage-brightness
response curve (Figure- 10), and additionally widens the viewing angle,
achieving a higher contrast.
The overall result is a higher performance type of display relative to the TND
Supertwisted Nematic Displays (STNDs)
Figure-10
Response curve of a STND (`- ) compared with the response of an ordinary TND (----).
The steeper response exhibited by the STND makes a wider range of brightness possible.
Display Construction
Back Plane Electrode
In order to utilise the
anisotropic properties of
LCs in an electrooptic
device, it is necessary to
provide means whereby
different regions of an
LC layer will show
different optical
properties
Alignment Layers
Liquid Crystalline
Material
OFF
Patterned
ITO Electrodes
Electric Field
ON
Apply Electric
Field to Some
of the ITO
Electrodes
5-20m
Electric
Field
Electric Field
OFF
ON
Final Comments
Clearly the most important applications of liquid crystals will remain in the area of
displays for the near future.
We can expect that the next generation of LCDs will be brighter and faster, finding
their way into new applications such as flat panel televisions, electronic
newspapers, and high intensity projection systems.
It might not be too far in the future that optical computing becomes commonplace,
and it will be interesting to see what role LCSLMs play in this new technology.
Likewise, polymer liquid crystals may find uses in displays as well, putting their
unique structural properties to good use.
While it is impossible to predict the future, liquid crystal technology over the last
quarter century has demonstrated an ability to sustain progress in two
important arenas, increased device performance and reduced product cost.
If these qualities continue, the future of liquid crystals will remain bright for years
to come.
Further Reading
• Depp, S. W. and Howard, W. E. (1993) Flat Panel Displays.
Scientific American, Vol. 268, 90-97, March.
• Mosley, A. (1993) Liquid Crystal Displays: An Overview.
Displays, 14, April.
• Schadt, M. (1989) The History of Liquid Crystal Display and
Liquid Crystal Material technology. Liquid Crystals, Vol. 5, 57-71
Operation Principles of TNDs
Figure- 9: Schematic representation of the (a) off- (bright) and (b) on-state (dark) geometry
of a TND. The polariser and analyser, which are arranged parallel to the LC director
orientation at the adjacent glass plates, are oriented at 900 (cross) to each other
Surface-Stabilised Ferroelectric Liquid
Crystal Display (SSFLCDs)
Ferroelectric LCs (FLCs) show a fast ( ~100 µs or less) switching rate
between two equally stable polarised states (P1 and P2) (Figure-11),
driven by the application of a reversible electric field.
The bistability of the FLC molecules to remain in either of the two opposite
polarised states, represents the basic principle for the development of
ferroelectric liquid crystal displays (FLCDs).
To date the FLCDs, which has been developed is the so-called surface –
stablised ferrolectric liquid crystal display (SSFLCD).
Figure-11
Figure-12
Surface-Stabilised Ferroelectric Liquid
Crystal Display (SSFLCDs)
The materials used in this type of device are based on the S C* phase with a tilt
angle (θ) of around 22.50. The surface alignment can unwound the helix of the
S C* phase.
Therefore, if the alignment layers separation is significantly smaller (order of 1 µ
m) than the pitch length, the competing surface stabilisation force does not allow
the helix to form.
The loss of the helical structure allows spontaneously ferroelectric domains to
appear in the absence of any applied electric field.
By applying a voltage, it is possible to favour the growth of one set of domains
(with polarisation P along the electric field ) over the other.
During the switching process, the molecules process in a cone-like fashion
(Figure-12), performing a rotation of 2θ (2 X 22. 50 = 450) about the normal to the
layers (Z).
The appropriate use of polarisers on both side of such a SSFLC cell will result in
the desired EO response in order to obtain an alternation of bright and dark
states, for each one of the opposite polarised states.
Fabrication Problems: SSFLCDs
SSFLCDs are mechanically unstable due to the poor anchoring of the FLC
film onto the glass surface,
The grey scale is not easily accessible due to the bistability of FLCs,
FLCs are extreme sensitivity to small temperature changes,
FLCs are highly viscous,
The small cell spacing, required to unwound the helical arrangement, makes the
SSFLCDs difficult to manufacture, with consequently high costs of fabrication.