* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Chapter 5
Survey
Document related concepts
Wake-on-LAN wikipedia , lookup
Passive optical network wikipedia , lookup
Zero-configuration networking wikipedia , lookup
Distributed firewall wikipedia , lookup
Recursive InterNetwork Architecture (RINA) wikipedia , lookup
Registered jack wikipedia , lookup
Cracking of wireless networks wikipedia , lookup
Piggybacking (Internet access) wikipedia , lookup
Asynchronous Transfer Mode wikipedia , lookup
Point-to-Point Protocol over Ethernet wikipedia , lookup
Computer network wikipedia , lookup
Power over Ethernet wikipedia , lookup
IEEE 802.1aq wikipedia , lookup
Network tap wikipedia , lookup
Transcript
Chapter Five Physical and Logical Topologies Simple Physical Topologies What does physical topology mean? The physical layout of the network nodes Bus, Ring, & Star What does logical topology mean? Network transmission methods Ethernet, Token Ring, LocalTalk, FDDI, ATM Simple Physical Topologies Physical topology Physical layout of a network A Bus topology consists of a single cable—called a bus— connecting all nodes on a network without intervening connectivity devices Figure 5-1: Bus topology network Simple Physical Topologies Figure 5-2: A terminated bus network Simple Physical Topologies Ring topology Each node is connected to the two nearest nodes so the entire network forms a circle One method for passing data on ring networks is token passing Three byte token used to pass data Active topology Each workstation transmits data Figure 5-3: A typical ring network Simple Physical Topologies Token passing process: Computer ready to transmit Computer picks up the token packet Adds control and data information plus the destination node’s address (the token is now a data frame) The token is then passed to the next node Once received by the destination, an acknowledgment is sent to the originating node After the originating node receives the acknowledgement, it releases a new free token which is sent down the ring Simple Physical Topologies Star topology Every node on the network is connected through a central device Figure 5-4: A typical star topology network Hybrid Physical Topologies Hybrid topology Complex combination of the simple physical topologies Star-wired ring Star-wired topologies use physical layout of a star in conjunction with token ring-passing data transmission method Fault tolerance of star – reliability of token passing Figure 5-5: A starwired ring topology network Hybrid Physical Topologies Star-wired bus In a star-wired bus topology, groups of workstations are star-connected to hubs and then networked via a single bus More expensive that star or bus Basis for modern Ethernet networks Figure 5-6: A star-wired bus network topology Hybrid Physical Topologies Daisy-Chained A Daisy chain is linked series of devices Drawback – Large # of hubs may affect transmission integrity Figure 5-7: A daisychained star-wired bus topology Hybrid Physical Topologies Hierarchical hybrid topology Uses layers to separate devices by priority or function Figure 5-8: A hierarchical ring topology Enterprise-Wide Topologies Enterprise An entire organization Backbone networks (commonly fiber, but may be CAT5 wiring) Serial backbone Distributed backbone Collapsed backbone Parallel backbone Enterprise-Wide Topologies Serial backbone (identical to daisy-chained networks) Two or more hubs connected to each other by a single cable Not suitable for large networks Distributed backbone Hubs connected to a series of central hubs or routers in a hierarchy Figure 5-9: A simple distributed backbone network Enterprise-Wide Topologies Figure 5-10: A distributed backbone connecting multiple LANs Enterprise-Wide Topologies Collapsed backbone Uses a router or switch as the single central connection point for multiple subnetworks (subnetworks may be different types) Figure 5-11: A collapsed backbone network Enterprise-Wide Topologies Parallel Backbone Collapsed backbone arrangement that consists of more than one connection from central router or switch to each network segment Figure 5-12: A parallel backbone network Enterprise-Wide Topologies Mesh networks Routers are interconnected with other routers, with at least two pathways connecting each router Internet Figure 5-13: An example of a mesh network Wide Area Network (WAN) Topologies Peer-to-peer topology WAN with single interconnection points for each location Dedicated circuits Continuous physical or logical connections between two access points that are leased from a telecommunication provider Figure 5-14: A peer-to-peer WAN Wide Area Network (WAN) Topologies Ring WAN topology Each site is connected to two other sites so that entire WAN forms a ring pattern Figure 5-15: A ring-configured WAN Wide Area Network (WAN) Topologies Star WAN topology Single site acts as the central connection point for several other points Figure 5-16: A starconfigured WAN Wide Area Network (WAN) Topologies Mesh WAN topology Many directly interconnected locations forming a complex mesh Figure 5-17: Full-mesh and partial-mesh WANs Wide Area Network (WAN) Topologies Tiered WAN topology Sites connected in star or ring formations are interconnected at different levels, with interconnection points organized into layers Figure 5-18: A tiered WAN topology Logical Topologies Refers to the way in which data are transmitted between nodes Describes the way: Data are packaged in frames Electrical pulses are sent over network’s physical media Logical topology may also be called network transport system Examples include: Ethernet, Token Ring, LocalTalk, FDDI, and ATM Switching Component of network’s logical topology that determines how connections are created between nodes Circuit switching Connection is established between two network nodes before they begin transmitting data Monopolized bandwidth between two nodes (not efficient) PC - ISP Message switching Establishes connection between two devices, transfers information to second device, and then breaks connection E-mail systems Packet switching Breaks data into packets before they are transmitted Ethernet and FDDI (including the Internet) Ethernet Carrier Sense Multiple Access with Collision Detection (CSMA/CD) The access method used in Ethernet Collision In Ethernet networks, the interference of one network node’s data transmission with another network node’s data transmission Collision rate > 5% is unusual Jamming Part of CSMA/CD in which, upon detection of collision, station issues special 32-bit sequence to indicate to all nodes on Ethernet segment that its previously transmitted frame has suffered a collision and should be considered faulty Ethernet Figure 5-19: CSMA/CD process Ethernet On an Ethernet network, an individual network segment is known as a collision domain Portion of network in which collisions will occur if two nodes transmit data at same time Data propagation delay Length of time data take to travel from one point on the segment to another point If to long, cannot identify collisions accurately Ethernet Demand priority Method for data transmission used by 100BaseVG Ethernet networks Demand priority requires an intelligent hub Figure 5-20: CSMA/CD versus demand priority Ethernet Traditional Ethernet LANs, called shared Ethernet, supply fixed amount of bandwidth that must be shared by all devices on a segment Switch Device that can separate network segments into smaller segments, with each segment being independent of the others and supporting its own traffic Switched Ethernet Newer Ethernet model that enables multiple nodes to simultaneously transmit and receive data over logical network segments Ethernet Figure 5-21: A switched Ethernet network * Increase the effective bandwidth of a network segment Ethernet Gigabit Ethernet 1 Gigabit Ethernet Ethernet standard for networks that achieve 1Gbps maximum throughput 10 Gigabit Ethernet Standard currently being defined by IEEE 802.3ae committee Will allow 10-Gbps throughput Will include full-duplexing and multimode fiber requirements Ethernet Ethernet frame types: IEEE 802.3 (“Ethernet 802.2” or “LLC”) Novell proprietary 802.3 frame (or “Ethernet 802.3”) Ethernet II frame IEEE 802.3 SNAP frame Padding Bytes added to data portion of an Ethernet frame to make sure this field is at least 46 bytes in size IEEE 802.3 (“Ethernet 802.2” or “LLC”) Default frame type for versions 4.x and higher of Novell NetWare network operating system Sometimes called LLC (Logical Link Control) frame In Novell’s lingo, this frame is called Ethernet 802.2 frame Figure 5-22: An IEEE 802.3 frame IEEE 802.3 (“Ethernet 802.2” or “LLC”) Service Access Point (SAP) Identifies node or internal process that uses LLC protocol Frame Check Sequence (FCS) This field ensures that data are received just as they were sent Cyclical Redundancy Check (CRC) Algorithm used by FCS field in Ethernet frames Novell Proprietary 802.3 (or “Ethernet 802.3”) Original NetWare frame type (NetWare 3.12-) Also called: 802.3 Raw Ethernet 802.3 frame Rarely used anymore Figure 5-23: A Novell proprietary 802.3 frame Ethernet II Original Ethernet frame type developed by DEC, Intel and Xerox, before IEEE began to standardize Ethernet Figure 5-24: An Ethernet II frame IEEE 802.3 SNAP Adaptation of IEEE 802.3 and Ethernet II SNAP stands for Sub-Network Access Protocol Organization ID (OUI) – identifies network type Rarely used on current networks Figure 5-25: An IEEE 802.3 SNAP frame Understanding Frame Types Learning about networks is analogous to learning a foreign language, with the frame type being the language’s syntax Just as you may know the Japanese word for go but how to use it in a sentence, you may know all about the IPX/SPX protocol but not how devices handle it Autosense Feature of modern NICs that enables a NIC to automatically sense what types of frames are running on a network and set itself to that specification Design Considerations for Ethernet Networks Cabling – coax or twisted-pair Connectivity devices – less expensive than comparable Token Ring or LocalTalk Number of stations – 10BaseT/100BaseTX limited to 1024 Speed – 10/100 Mbps, 1 and 10 Gbps (soon) Scalability – easily expandable Topology – 10BaseT/100BaseTX use star-wired bus hybrid topology (highly fault tolerant) LocalTalk Logical topology designed by Apple Computer, Inc. Uses a transmission method called Carrier Sense Multiple Access/Collision Avoidance (CSMA/CA) Similar to CSMA/CD, except node signals intent before it actually does A teleconnector is a transceiver used on a LocalTalk network Macintosh version of TCP/IP is called MacTCP Token Ring Token Ring networks use the token passing routine and a star-ring hybrid physical topology The 100-Mbps Token Ring standard is known as High-Speed Token Ring (HSTR) On a Token Ring network, one workstation, called the active monitor, acts as the controller for token passing Token Ring Multistation Access Unit (MAU) Regenerates signals Figure 5-26: Interconnected Token Ring MAUs Token Ring Control Access Unit (CAU) Connectivity device used on a Token Ring network, similar to MAU but more flexible and allows easier management of nodes Lobe Attachment Module (LAM) Device that attaches to a CAU to expand the capacity of that device Token Ring Token Ring networks with STP cabling may use a type 1 IBM connector A DB-9 connector is another type of connector found on STP Token Ring networks Figure 5-27: Type 1 IBM and DB-9 Token Ring connectors Token Ring Media filter Device that enables two types of cables or connectors to be linked Token Ring media filter Enables DB-9 cable and type 1 IBM cable to be connected Figure 5-28: A Token Ring media filter Token Ring Token Ring switching Like Ethernet networks, Token Ring networks can take advantage of switching to better utilize limited bandwidth Token Ring frames IEEE 802.5 Token Ring frame IBM Token Ring frame Figure 5-29: An IBM Token Ring frame Design Considerations for Token Ring Networks Cabling – shielded/unshielded twisted pair Connectivity devices – more expensive than Ethernet Number of stations – 255 STP – 72 UTP Speed – 4/16/100 Mbps Scalability – Easily daisy-chain MAUs Topology – Star-wired ring topology (highly fault-tolerant) Fiber Distributed Data Interface (FDDI) Logical topology whose standard was originally specified by ANSI in mid-1980s and later refined by ISO Double ring of multimode or single mode fiber to transmit data Figure 5-30: A FDDI network Asynchronous Transfer Mode (ATM) Describes both a network access method & a multiplexing technique Logical topology that relies on a fixed packet size to achieve data transfer rates up to 9,953 Mbps Typically used on WANs The fixed packet in ATM is called a cell A unique aspect of ATM technology is that it relies on virtual circuits Connections between network nodes logically appear to be direct, dedicated links between the two nodes Asynchronous Transfer Mode (ATM) ATM uses circuit switching, which allows ATM to guarantee a specific quality of service (QoS) QoS – standard that specifies that data will be delivered within a certain period of time after the transmission ATM technology can be integrated with Ethernet or Token Ring networks through the use of LAN Emulation (LANE) ATM is very expensive Gigabit Ethernet is a better choice