Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Logic Values 0:logic 0 / false 1:logic 1 / true X:unknown logic value Z:high-impedance Strength levels Strength level supply strong pull large weak medium small highz Type Degree Driving strongest Driving Driving Storage Driving Storage Storage High Impedance weakest Data Types Nets Connects between hardware elements Must be continuously driven by Continuous assignment (assign) Module or gate instantiation (output ports) Default initial value for a wire is “Z” (and for a trireg is “x”) Registers Represent data storage elements Retain value until another value is placed on to them Similar to “variables” in other high level language Different to edge-triggered flip-flop in real ciucuits Do not need clock Default initial value for a reg is “X” Examples reg a; // a scalar register wand w; // a scalar net of type “wire and” reg [3:0] v; // a 4-bit vector register from msb to lsb reg [7:0] m, n; // two 8-bit registers tri [15:0] busa; // a 16-bit tri-state bus wire [0:31] w1, w2; // Two 32-bit wires with msb being the 0 bit, not recommended Net Types The most common and important net types wire and tri for standard interconnection wires wire: single driver e.g. output of “and” gate tri: multiple driver e.g. multiplexer supply1 and supply0 “x” strong1 and supply1 “supply1” Net Types Other wire types wand, wor, triand, and trior for multiple drivers that are wired-anded and wired-ored tri0 and tri1 pull down and pull up trireg for net with capacitive storage If all drivers at z, previous value is retained Two states: Driven state: at least one driver drives 0, 1, x Capacitive state: all driver have high impedance “z” Strength: small, medium, large; default is medium An example for wire, tri0, tri1 module tritest(); wire w1, w2, w3, w4; tri0 t01, t02, t03, t04; tri1 t11, t12, t13, t14; assign w1 = 0; assign t01 = 0; assign t11 = 0; assign w2 = 1'bz; assign t02 = 1'bz; assign t12 = 1'bz; assign w3 = 1; assign t03 = 1; assign t13 = 1; Initial begin #1;$display(w1, w2, w3, w4); $display(t01, t02, t03, t04); $display(t11, t12, t13, t14); end endmodule Results: 0z1z 0010 0111 Register Types reg Integer integet a,b; // declaration 32-bit signed (2’s complement) Time any size, unsigned 64-bit unsigned, behaves like a 64-bit reg $display(“At %t, value=%d”,$time,val_now) real real c,d; //declaration 64-bit real number Defaults to an initial value of 0 Numbers & Negative Numbers Constant numbers are integer or real constants. Integer constants are written as “width ‘radix value” The radix indicates the type of number Decimal (d or D) Hex (h or H) Octal (o or O) Binary (b or B) A number may be sized or unsized Number Specification (continue) Sized numbers <size>’<base_format><number> <size> is in decimal and specifies the number of bits ‘<base_format> is: ‘d ‘D ‘h ‘H ‘b ‘B ‘o ‘O The <number> digits are 0-f, uppercase may be used Examples: 4’b1111 12’habc 16’d255 Number Specification Unsized numbers – The <size> is not specified (default is simulator/compiler specific, >= 32 bits) Numbers without a base are decimal by default Examples 100 6’h3a 1’bx 32’bz // Decimal 100, 32 bits by default // Binary 111010 // One-bit X // 32 bits of High-Z (impedance) Operators Example assign A1 = (3+2) %2; // A1 = 1 assign A2 = 4 >> 1; assign A4 = 1 << 2; // A2 = 2 A4 = 4 assign Ax = (1= =1'bx); //Ax=x assign Bx = (1'bx!=1'bz); //Bx=x assign D0 = (1= =0); //D0=False assign D1 = (1= =1); //D1=True assign E0 = (1= = =1'bx); //E0=False assign E1 = (4'b01xz = = = 4'b01xz);; //E1=True assign F1 = (4'bxxxx = = = 4'bxxxx); //F1= True assign x = a ? b : c //if (a) then x = b else x = c Concatenation operator // A=1’b1; B=2’b00, C=2’b10; D=3’b110; Y={B, C} //Result Y is 4’b0010 Y={A, B, C, D, 3’b001} //Result Y is 11’b10010110001 Y={A, B[0], C[1]} // Result Y is 3’b101 Replication operator Reg A; Reg [1:0] B, C; Reg [2:0] D; A=1’b1; B=2’b00, C=2’b10; D=3’b110; Y={4{A}} // Result Y is 4’b1111 Y={4{A}, 2{B}} // Result Y is 8’b11110000 Y ={4{A}, 2{B}, C} //Result Y is 8’b1111000010 Example – Multiplexer_1 // Verilog code for Multiplexer implementation using assign // File name: mux1.v // by Harsha Perla for http://electrosofts.com // [email protected] // Available at http://electrosofts.com/verilog module mux1( select, d, q ); input [1:0] select; input [3:0] d; output q; wire q; wire[1:0] select; wire[3:0] d; assign q = d[select]; endmodule Example – Multiplexer_2 // Verilog code for Multiplexer implementation using always block. // by Harsha Perla for http://electrosofts.com // [email protected] // Available at http://electrosofts.com/verilog module mux2( select, d, q ); input[1:0] select; input[3:0] d; output q; reg q; wire[1:0] select; wire[3:0] d; always @(d or select) q = d[select]; endmodule Example – Multiplexer_3 module mux4_1 (out, in0, in1, in2, in3, sel) ; output out ; input in0,in1,in2,in3 ; input [1:0] sel ; assign out = (sel == 2'b00) ? in0 : (sel == 2'b01) ? in1 : (sel == 2'b10) ? in2 : (sel == 2'b11) ? in3 : 1'bx ; endmodule Exercise Design an 1-to-8 Demultiplexer