Download Micro Relay A/VFMA Automotive Relays Plug-in Micro ISO Relays

Automotive Relays
Plug-in Micro ISO Relays
Micro Relay A/VFMA
■ High current version with limiting continuous current 30A at 85°C
■ Pin assignment according to ISO 7588 part 3
■ Customized versions on request
– 24VDC versions with special contact gap
– Integrated components (e.g. diode)
– Customized marking
– Special covers (e.g. notches, release features)
– For latching version refer to Micro Relay Latching
– For low noise version refer to Micro Relay Low Noise
– For high current version refer to part number table
Typical applications
Cross carline up to 30A for example: ABS control, blower fans, cooling fan,
door control, door lock, fuel pump, heated front screen, immobilizer, interior
lights, seat control, seatbelt pretensioner, sun roof, trunk lock, valves,
window lifter, wiper control.
F074_fcw1_bw
FVFMA_fcw1c
Contact DataForm A Standard
Form C
Form A HC
Form C HC
Contact arrangement
1 form A, 1 form A, 1 form C, 1 form C, 1 form A, 1 form C
1 NO
1 NO
1 CO
1 CO
1 NO
1 CO
Rated voltage
12VDC
24VDC
12VDC
24VDC6)
12VDC 12VDC
Limiting continuous current, form A/form B NO/NC
NO/NC
23°C
30A
30A
30/20A 30/20A
35A
35/25A
85°C
25A
25A
25/15A 25/15A
30A
30/20A
125°C
10A
10A
10/8A
10/8A 15A
15/10A
Limiting making current1)2), A/B (NO/NC)
120A
120A
120/40A
120/20A
120A
120/40A
Limiting breaking current
30A
20A
30/15A
20/10A
30A
30/20A
Limiting short-time current,
overload current, ISO 8820-33)
1.35 x 25A, 1800s 1.35 x 25A, 1800s1.35 x 30A, 1800s
2.00 x 25A, 5s 2.00 x 25A, 5s 2.00 x 30A, 5s
3.50 x 25A, 0.5s 3.50 x 25A, 0.5s 3.50 x 30A, 0.5s
6.00 x 25A, 0.1s 6.00 x 25A, 0.1s 6.00 x 30A, 0.1s
Jump start test24VDC for 5min conducting nominal current at 23°C
Contact material
silver based
Min. recommended contact load4)
1A at 5VDC
Initial voltage drop
NO contact at 10A, typ./max.
15/200mV
NC contact at 10A, typ./max. 20/250mV
Frequency of operation
6 ops./min (0.1Hz)
Electrical endurance5)
resistive load at 14VDC
>1x105 ops.
>1x105 ops. >1x105 ops.
25A
25A (NO)
30A
resistive load at 28VDC >1x105 ops. >1x105 ops.
15A
15A (NO)
>1x105 ops.
10A (NC)
Mechanical endurance
typ. 107 ops.
Max. DC load breaking capacity
1) The values apply to a resistive or inductive load with suitable spark suppression and at
maximum 13.5VDC for 12VDC or 27VDC for 24VDC load voltages.
2) For a load current duration of maximum 3s for a make/break ratio of 1:10.
3) Current and time are compatible with circuit protection by a typical automotive fuse.
Relay will make, carry and break the specified current.
4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at
http://relays.te.com/appnotes/
5) Electrical endurance data are only valid for the variants with resistor.
6) Not applicable for polarity reverse loads like powerwindows
Load limit curve 1: arc extinguishes during transit time (CO contact).
Load limit curve 2: safe shutdown, no stationary arc (NO contact).
Load limit curves measured with low inductive resistors verified for 1000 switching events.
05-2016, Rev. 0516
www.te.com
© 2016 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Datasheets and product specification according to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ section, application notes and all specifications
are subject to change.
1
Automotive Relays
Plug-in Micro ISO Relays
Micro Relay A/VFMA (Continued)
Coil Data
Coil voltage range
Other Data
12/24VDC
Coil versions, DC coil
Coil
Rated
Operate
Release
Coil
Rated coil
codevoltagevoltagevoltage
resistance7)power7)
VDCVDCVDC
Ω±10%W
001
12
7.2
1.6
119
1.20
0022414.4 3.64301.34
005
12
7.2
1.6
144
1.00
F 12 7.21.2901.60
H 2414.4 3.64301.34
All figures are given for coil without pre-energization, at ambient temperature +23°C.
7) Without components in parallel.
Coil operating range
TE074_OVR1
Does not take into account the temperature rise due to the contact current
E = pre-energization.
8) No change in the switching state >10µs. Valid for NC contacts, NO contact values
significantly higher.
9) Values apply 2mm from the end of the terminal. When the force is removed, the terminal
must not have moved by more than 0.3mm
Insulation Data
Initial dielectric strength
between open contacts
between contact and coil
Load dump test
ISO 7637-1 (12VDC), test pulse 5
ISO 7637-2 (24VDC), test pulse 5
EU RoHS/ELV compliance
compliant
Ambient temperature
-40 to +125°C
Climatic cycling with condensation,
EN ISO 6988
6 cycles, storage 8/16h
Temperature cycling,
IEC 60068-2-14, Nb 10 cycles, -40/+85°C (5°C/min)
Damp heat cyclic,
IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temp. 55°C
Damp heat constant,
IEC 60068-2-3 (78), Ca
56 days
Category of environmental protection,
IEC 61810
RT I – dustproof
Degree of protection, IEC 60529
IP54
Corrosive gas
IEC 60068-2-42 10±2cm3/m3 SO2, 10 days
IEC 60068-2-43 1±0.3cm3/m3 H2S, 10 days
Vibration resistance (functional)
IEC 60068-2-6 (sine sweep)
10 to 500Hz min. 5g8)
Shock resistance (functional)
IEC 60068-2-27 (half sine)
min. 20g 11ms8)
Drop test, free fall, IEC 60068-2-32
1m onto concrete
Terminal type
plug-in, QC
Cover retention
axial force
150N
Does not take into account
pull force
150N
the temperature rise due to
push force
200N
the contact current
retention
E =Terminal
pre-energization
pull force
100N
push force
100N
resistance to bending
10N9)
force applied to side
10N9)
torque
0.3Nm
Weightapprox. 16 to 20g (0.5 to 0.7oz)
Packaging unit
Micro A 480 pcs.
VFMA 600 pcs.
500VACrms
500VACrms
Accessories
For details see datasheet Connectors for Micro ISO Relays
Vs=+86.5VDC
Vs=+200VDC
Terminal Assignment
NOD
1 form A, 1 NO with diode
2
NOR
1 form A, 1 NO with resistor
COD
1 form C, 1 CO with diode
2
5
2
5
2
1
3
1
3
1
05-2016, Rev. 0516
www.te.com
© 2016 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Datasheets and product specification according to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
5
4
3
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
COR
1 form C, 1 CO with resistor
2
1
5
4
3
Datasheets, product data, ‘Definitions’ section, application notes and all specifications
are subject to change.
Automotive Relays
Plug-in Micro ISO Relays
Micro Relay A/VFMA (Continued)
Dimensions
Quick connect terminal similar to ISO 8092-1.
Micro A: Terminals without holes
VFMA: Terminals with holes
View of the terminals (bottom view)
05-2016, Rev. 0516
www.te.com
© 2016 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Datasheets and product specification according to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ section, application notes and all specifications
are subject to change.
3
Automotive Relays
Plug-in Micro ISO Relays
Micro Relay A/VFMA (Continued)
Product code structure
Typical product code V23074 -A 1 001-A4 02
Type
V23074 Micro Relay A
Version
A
Standard
Coil suppression
1
Resistor
Coil
001 12VDC
Contact material
-A4 Silver based
Contact arrangement
02
1 form A, 1 NO
H
High current
2
Diode
002
24VDC
-A5
Silver based for high current version
03
1 form C, 1 CO
005
Product code structure
V23074-A1001-A402
VFMA-11F41-S01
V23074-A1001-A403
VFMA-15F41-S01
V23074-A2001-A402
V23074-A2001-A403
V23074-H1005-A502
V23074-A1002-A402
VFMA-11H41-S01
V23074-A1002-A403
V23074-A2002-A402
V23074-A2002-A403
VFMA
-11F41
-S01
Typical product code
Type
VFMA VFMA Series
Version
1 Standard
Contact arrangement
1 1 form A, 1 NO
Coil
F 12VDC
Contact material
4 Silver based
Terminals
1 Plug-in
Coil suppression
S01 Resistor
Product code
12VDC for high current version
5
1 form C, 1 CO
H 24VDC
7
Equivalent to
VFMA-11F41-S01
V23074-A1001-A402
VFMA-15F41-S01
V23074-A1001-A403
VFMA-11H41-S01
V23074-A1002-A402
Silver based for high current version
Version
Standard
Circuit1)
Coil suppr.
Resistor 680Ω
NOR
Diode
High current Resistor 1000Ω
Standard Resistor 1800Ω
Coil
12VDC
1 form A, 1 NO
COR
1 form C, 1 CO
NOD
COD
NOR
1 form A, 1 NO
1 form C, 1 CO
1 form A, 1 NO
24VDC
COR
NOD
COD
Diode
Arrangement Terminals Part number
Plug-in, QC
1 form C, 1 CO
1 form A, 1 NO
1 form C, 1 CO
4-1904124-2
9-1393292-9
4-1904124-3
1393293-8
5-1393292-8
6-1419137-4
4-1904124-4
8-1393292-9
6-1415008-2
3-1393292-8
6-1393292-2
6-1393292-3
1) See terminal assignment diagrams.
Other types on request.
This list represents the most common types and does not show all variants covered by this datasheet.
Production in Asia (only)
Product code
V23074-A1001-A402
V23074-A1001-A403
V23074-A2001-A402
V23074-A2001-A403
V23074-H1005-A502
Version
Standard
Coil suppression
Resistor 680Ω
Diode
High current
Resistor 1000Ω
Circuit1)
NOR
COR
NOD
COD
NOR
Coil
12VDC
Arrangement
1 form A, 1 NO
1 form C, 1 CO
1 form A, 1 NO
1 form C, 1 CO
1 form A, 1 NO
Terminals Part number
Plug-in, QC
1393292-5
8-1393292-4
2-1904111-7
9-1904105-7
2-1414971-4
1) See terminal assignment diagrams.
Other types on request.
This list represents the most common types and does not show all variants covered by this datasheet.
4
05-2016, Rev. 0516
www.te.com
© 2016 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Datasheets and product specification according to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ section, application notes and all specifications
are subject to change.