Download File - Thurso High Technologies

Document related concepts

Negative resistance wikipedia , lookup

Oscilloscope history wikipedia , lookup

Nanofluidic circuitry wikipedia , lookup

Spark-gap transmitter wikipedia , lookup

Integrating ADC wikipedia , lookup

Josephson voltage standard wikipedia , lookup

Valve RF amplifier wikipedia , lookup

Test probe wikipedia , lookup

Wilson current mirror wikipedia , lookup

Multimeter wikipedia , lookup

Transistor–transistor logic wikipedia , lookup

Operational amplifier wikipedia , lookup

TRIAC wikipedia , lookup

CMOS wikipedia , lookup

Power electronics wikipedia , lookup

Schmitt trigger wikipedia , lookup

Voltage regulator wikipedia , lookup

Electrical ballast wikipedia , lookup

Opto-isolator wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Surge protector wikipedia , lookup

Current source wikipedia , lookup

Ohm's law wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Power MOSFET wikipedia , lookup

Rectiverter wikipedia , lookup

Current mirror wikipedia , lookup

Transcript
Electronics
Use your mouse to move around
the software. You can either click
anywhere on the screen to get the
next animation or click on a
button if you can see one on the
screen.
Always move the mouse before
you click it.
 TPS 2002
1
Electronics
Introduction
Ohm’s Law
Power Calculations
Resistors in Series and Parallel
Capacitors
Alternating Current
Waveforms
The Potential Divider
Transistor Circuits
Questions
2
Introduction
Basic Concepts
Simple Circuits
Questions
Main Menu
3
Basic Concepts
Electric current is due to the flow of charge.
In a solid conductor, the charge is carried by electrons.
In a solid conductor, an electric current is due to the flow
of electrons.
4
Return previous slide
Basic Concepts
Conductors include:
copper
gold
silver
All metals
lead
And water (not distilled) which is why you should not use mains
appliances in the presence of water.
5
Return previous slide
Basic Concepts
Insulators include:
Rubber
Plastic
Most solid non metals
Glass
Glass, unless it is very hot, is one of the best insulators available.
6
Return previous slide
Basic Concepts
Electric current (I) is measured in ampere (A) - I is the symbol used to
indicate current.
The “amp” is a rather large unit for most electronic applications so we
use the following sub-multiples:
1 mA = 0.001A that is 1 / 1 000 th of an ampere
You already know that 1mm is 1/1000th of an metre so there is nothing
new here.
1 A = 0.000 001A that is 1 / 1 000 000 th of an ampere
7
Return previous slide
Basic Concepts
Voltage is measured in volt (V)
Common sub-multiples of the volt (less than a volt) include:
1 mV = 0.001V that is 1 / 1 000 th of a volt
1 V = 0.000 001V that is 1 / 1 000 000 th of a volt
Common multiples of the volt (greater than a volt) include:
1 kV = 1 000 V
1 MV = 1 000 000 V
The kV and the MV are not common in electronics.
8
Return previous slide
Basic Concepts
Resistance is measured in ohm ()
Common sub-multiples of the ohm (less than an ohm) include:
1 m  = 0.001  that is 1 / 1 000 th of an ohm
1   = 0.000 001  that is 1 / 1 000 000 th of an ohm
This is pronounced micro ohm
Common multiples of the ohm (greater than an ohm) include:
1 k  = 1 000 
1 M  = 1 000 000 
The m and the   are not common in electronics.
9
Return previous slide
Basic Concepts
Capacitance is measured in farad (F)
Common sub-multiples of the farad (less than a farad) include:
1 m F = 0.001 F that is 1 / 1 000 th of a farad
1  F = 0.000 001 F that is 1 / 1 000 000 th of a farad
1 n F = 0.000 000 001 F that is 1 / 1 000 000 000 th of a farad
this is written in full as a nano farad
1 p F = 0.000 000 000 001 F that is 1 / 1 000 000 000 000 th of a farad
This is written in full as pico farad
10
Return previous slide
Basic Concepts
Here is a summary of many of the available multiples and sub-multiples
Symbol
Prefix Multiplication factor
T
tera 1012 1 000 000 000 000
G
giga 109
1 000 000 000
M
mega 106
1 000 000
k
kilo 103
1 000
h
hecto 102
100
da
deca 101
10
d
deci 10-1 0.1
The most
-2
c
centi 10
0.01
m
milli 10-3 0.001 frequently used

micro 10-6 0.000 001 are in bold.
n
nano 10-9 0.000 000 001
p
pico 10-12 0.000 000 000 001
f
femto 10-15 0.000 000 000 000 001
11
a
atto 10-18 0.000 000 000 000 000 001
Return previous slide
Basic Concepts
Resistors are marked with a series of coloured rings to give us an idea of
how big their resistance is.
This gold band indicates that the tolerance
of the resistor is ±5% (plus or minus 5 percent).
This means that its resistance is between 3 400 
and 3 800 . We say it is nominally 3 600 .
The third band is red. This means that there are 2 zeros.
The second band is blue. This means the second digit is 6.
The first band is orange. This means the first digit is 3.
So the resistor is nominally 3 600 .or 3k6
12
Return previous slide
Basic Concepts
The colours used for the first three bands and their meanings are as
follows:
Colour
Number
Number of zeros
Black
0
none
Brown
1
0
Red
2
00
Orange
3
000
Yellow
4
0 000
Green
5
00 000
Blue
6
000 000
Violet
7
0 000 000
Grey
8
00 000 000
White
9
000 000 000
13
Return previous slide
Basic Concepts
The colours used for the last band and their meanings are as follows:
Gold
±5%
Silver
± 10 %
No band
± 20 %
Resistors are manufactured in “preferred values”. That
means that you can only buy certain values.
The preferred values for resistors with a tolerance of
±20% are: 10,15,22,33,47,68 and 100. These are just
the first two significant figures. You can buy a 1500
but not a 2000 .
14
Return previous slide
Basic Concepts
The preferred values for 10% resistors are:
10
12
47
15
56
18
22
27
&
58
82
100
33
39
15
Return previous slide
Basic Concepts
The preferred values for 5% resistors are:
10
39
11
43
12
47
13
51
15
56
16
62
18
68
20
75
22
82
24
91
27
100
30
33
36
&
16
Return previous slide
Basic Concepts
Home
In summary:
Voltage is measured in Volt (V)
Current is measured in Ampere (A)
Resistance is measured in ohm ()
Capacitance is measured in farad (F)
3MV = 3 000 000 V
2kV = 2 000 V
5mV = 0.005 A
&
1nF = 0.000 000 001 F
1pF = 0.000 000 000 001 F
7A = 0.000 007 A
17
Return previous slide
Simple Circuits
Simple circuits have three main blocks of components in common that
perform the same type of job. These are:
Input
Processor
Output
This is called a block diagram.
•The processor is the decision-making part of the system.
•The input is a sensor that transforms everyday phenomena such as
temperature and heat to an electric signal that the processor can deal
with.
•The output is a device that converts an electric signal from the processor
into something that we want.
18
Return to menu slide
Simple Circuits
Simple circuits have three main blocks of components in common that
perform the same type of job. These are:
Input
Processor
Output
Examples of input devices include:
Pressure pads
LDRs
Thermistors
Reed switches
19
Return to previous slide
Simple Circuits
Simple circuits have three main blocks of components in common that
perform the same type of job. These are:
Input
Processor
Output
Examples of output devices include:
Lamps
LEDs
Motors
Solenoids
20
Return to previous slide
Simple Circuits
Simple circuits have three main blocks of components in common that
perform the same type of job. These are:
Input
Processor
Output
Examples of basic processors include:
Transistors
Operational amplifiers
21
Return to previous slide
Simple Circuits
Home
Simple circuits have three main blocks of components in common that
perform the same type of job. These are:
Input
Processor
Output
What would the block diagram look like for a system that brought on a
light when it got dark?
LDR
Processor
Lamp
22
Return to previous slide
Questions - Simple Circuits
1
Write down the units of voltage, capacitance, resistance and
ANSWER
current. What is the symbol for current?
2
Write out 22mA and 420 pF in full.
3
Give three examples of input devices.
ANSWER
ANSWER
4
Write out a block circuit diagram for a device that could lift up a
ANSWER
trap door when a beam of light was broken.
5
What is the nominal value and tolerance of this resistor?
ANSWER
6
What would the colours of a 47M resistor be?
ANSWER
23
Return to menu slide
Solutions - Simple Circuits
1
Write down the units of voltage, capacitance, resistance and
current. What is the symbol for current?
Voltage
volt (V)
Capacitance
farad (F)
Resistance
ohm ()
Current
ampere (A)
The symbol for current is I
24
Return
Solutions - Simple Circuits
2
Write out 22mA and 420 pF in full.
22mA = 22 x 0.001 A = 0 . 22 A
420 pF = 420 x 0.000 000 000 001 F = 0 . 000 000 000 42 F
25
Return
Solutions - Simple Circuits
3
Give three examples of input devices.
Pressure pads
LDRs
Thermistors
Reed switches
26
Return
Solutions - Simple Circuits
4
Write out a block circuit diagram for a device that could lift up a
trap door when a beam of light was broken.
LDR
Processor
Motor
or
LDR
Processor
Solenoid
Note that a bulb is not an input device as it gives out light.
27
Return
Solutions - Simple Circuits
5
What is the nominal value and tolerance of this resistor?
This gold band indicates that the tolerance
of the resistor is ±5% (plus or minus 5 percent).
The third band is red. This means that there are 2 zeros.
The second band is black. This means the second digit is 0.
The first band is brown. This means the first digit is 1.
28
So the resistor is nominally 1 200 .
Return
Solutions - Simple Circuits
6
What would the colours of a 47M resistor be?
The resistor is nominally 47 000 000 .
This gold band indicates that the tolerance
of the resistor is ±5% (plus or minus 5 percent).
The third band is blue. This means that there are 6 zeros.
The second band is violet. This means the second digit is 7.
The first band is yellow. This means the first digit is 4.
29
Return
Ohm’s Law
Ohm’s Law states that so long as the physical conditions remain
constant, the current through a conductor is proportional to the voltage
across it.
This gives us the formula:
Voltage = current x resistance
V=IR
We can rearrange this equation to give either
R=V/I
or
I=V/R
30
Return to menu slide
Ohm’s Law
What does it mean?
“Physical conditions remaining constant” - This really means as long
as the temperature remains constant. Usually it does.
“The current through a conductor is proportional to the voltage across
it” - this means that if you double the voltage, you get twice the
current. Triple the voltage and you triple the current etc.
Low resistance
Current
High resistance
Voltage
31
Return previous slide
Ohm’s Law
Calculations using Ohm’s law fall into three types:
What is the resistance
if ? (Use R = V / I)
E.G.
What resistance could
you use with a 10V
supply to limit the
current to 15mA?
R = V / I = 10 / 0.015
667  so use 680 
What is the current
if ? (Use I = V / R)
E.G.
A 430  resistor
protects an LED in a
5V circuit. What is
the current through
the LED?
I = V / R = 5 / 430
= 12 mA
What is the voltage
if ? (Use V = I x R)
E.G.
12mA runs through
a prorctive resistor
of resistance 820 .
What is the voltage
across the resistor ?
V = IR = 0.012x820
= 9.84 V
32
Return previous slide
Ohm’s Law
0.7 V
820 
Diode
The voltage across the diode is 0.7
V and the cell produces 1.5 V. What
is the current through the resistor?
1.5V
If you can’t see how to do it straight away, write the values
given onto the diagram.
Voltage across the resistor = 1.5V (provided by the cell)
- 0.7V (lost across the diode) = 0.8V
Using I = V / R = 0.8 / 820 = 1mA
33
Return previous slide
Ohm’s Law - Questions
Home
1
A power supply drives a current of 500mA through a bulb with a
working resistance of 3. What voltage is the power supply?
2
A power supply provides 12 V to a bulb passing 3 A. What is the
working resistance of the bulb?
3
A 47 k resistor has a pd of 9 V across it. What current passes
through the resistor?
4
An 18V power supply is placed across a resistor of resistance
10k. What current will flow through the resistor?
5
The effective resistance of a small motor is 5 . What current
passes through it if a cell of voltage 6 V is placed across it?
Solution 1
Solution 2 Solution 3
Solution 4
Solution 5
34
Return previous slide
Ohm’s Law - Solutions
1
A power supply drives a current of 500mA through a bulb with a
working resistance of 3. What voltage is the power supply?
V=IxR
so V = 0.5 x 3
=1.5 volt
35
Return
Ohm’s Law - Solutions
2
A power supply provides 12 V to a bulb passing 3 A. What is the
working resistance of the bulb?
V=IxR
So R = V / I
= 12 / 3
= 4A
36
Return
Ohm’s Law - Solutions
3
A 47 k resistor has a pd of 9 V across it. What current passes
through the resistor?
V=IxR
So I = V / R
= 9 / 47 000
= 0.000 191 A
= 191 A
37
Return
Ohm’s Law - Solutions
4
An 18V power supply is placed across a resistor of resistance
10k. What current will flow through the resistor?
V=IxR
so I = V / R
= 18 / 10 000
= 0.001 8 A
= 1.8 mA
38
Return
Ohm’s Law - Solutions
5
The effective resistance of a small motor is 5 . What current
passes through it if a cell of voltage 6 V is placed across it?
V=IxR
So I = V / R
=6/5
= 1.2 A
39
Return
Power Calculations
The detail from the bottom of an
electrical appliance shown here
gives a very useful, commonly
used method of writing the power
of the appliance.
20 VA is exactly the same as 20 W (20 watts).
The more powerful an appliance is, the greater the number will be.
An electric fire might well be 2 or 3 kW (2 000 or 3 000 W).
1W is sometimes called 1VA because you can calculate the
power by multiplying “the volts by the amps”!
Power = current x voltage or P = I V
40
Return main menu
Power Calculations
Remember that :
20VA means a power of 20W
and that
P=IxV
This device runs from a 230V mains supply. What can we learn from
this information? Well, we know that P = IV; we also know the voltage
and the power, so we can calculate the current I.
I=P/V
So I = 20 / 230
= 87 mA
41
Return previous slide
Power Calculations
Can you match these typical power ratings with the device that they
describe?
Torch Bulb
42
Return previous slide
Power Calculations
Torch Bulb
43
Return previous slide
Power Calculations - the formulae
Power = current x voltage
P = IV
so I = P / V and V = P / I
But from Ohm’s Law, V = I x R
So P = I x IR
P = I2 R
And from Ohm’s Law, I = V / R
So P = (V/R) x V
P = V2/R
44
Return previous slide
Power Calculations - Questions
Home
1
A diode has a voltage of 0.7V across it and a current of 100mA
flowing through it. What is the power dissipated in the diode?
2
A wire carries a current of 5 mA and the power dissipated in the
wire is 2.5 W. What is the voltage across the wire?
3
What is the current passing through a coil that dissipates 40mW
when a voltage of 5V is applied across it?
4
A current of 10 mA passes through a 10 resistor. What is the
power dissipated in the resistor?
5
A voltage of 9 V is applied across a 10 k  resistor. What power
is dissipated in the resistor?
45
Return previous slide
Power Calculations - Solutions
1
A diode has a voltage of 0.7V across it and a current of 100mA
flowing through it. What is the power dissipated in the diode?
P = IV
so P = 0.1 x 0.7
= 0.07
= 70 mW
46
Power Calculations - Solutions
2
A wire carries a current of 5 mA and the power dissipated in the
wire is 2.5 W. What is the voltage across the wire?
P = IV
So V = P / I
= 0.000 0025 / 0.005
= 0.000 5 W
= 0.5 mW
= 500 W
47
Power Calculations - Solutions
3
What is the current passing through a coil that dissipates 40mW
when a voltage of 5V is applied across it?
P = IV
So I = P / V
= 0.04 / 5
= 0.008 W
= 8mW
48
Power Calculations - Solutions
4
A current of 10 mA passes through a 10 resistor. What is the
power dissipated in the resistor?
P = I2R
= 0.012 x 10
= 0.001
=1mW
49
Power Calculations - Solutions
5
A voltage of 9 V is applied across a 10 k  resistor. What power
is dissipated in the resistor?
P =V2/R
= 92 / 10 000
0.0081
= 8.1 mW
50
Resistors in Series and Parallel
Resistors are said to be connected in series when the same current has to
pass through each resistor i.e. the current does not have to split.
These three resistors are connected in series.
And so are these 5 resistors
51
Return to main menu
Resistors in Series and Parallel
Resistors are said to be connected in parallel when the current has to
split to pass through each resistor i.e. the current through each resistor
might not be the same.
These three resistors are connected in
parallel.
And so are these two.
52
Return to previous slide
Resistors in Series and Parallel
R1
R2
47 M
47 M
R3
47 M
These three resistors connected in series, could be replaced by
one resistor of resistance 141M.
That is 47 M + 47 M + 47 M = 141 M
(This is not available so we might use a 150 M)
As a general formula we could write:
R total= R1 + R2 + R3
or
R = R1 + R2 + R3
53
Return to previous slide
Resistors in Series and Parallel
R1
The resistance of each of the resistors
in this parallel network is 47 M.
The effective resistance of three
resistors is 15.7 M (use 16 M).
R2
R3
You would expect the resistance to be less than any of the individual
resistances in the network as there are three possible routes for the
electricity to take.
The formula used to add the resistances is:
1
Rtotal
or

RTotal
1
R1


1
R2

1
R3
R1R2 R3
R1R2  R2 R3  R3 R1
54
Return to previous slide
Resistors in Series and Parallel - Questions
Home
1
What is the combined resistance of a 39k  and a 47k  resistor
connected in series?
2
What is the combined resistance of a 39k  and a 47k  resistor
connected in parallel?
3
What is the combined resistance of a 10k , 20k  and 47k 
resistor connected in series?
4
What is the combined resistance of a 10k , 20k  and 47k 
resistor connected in parallel?
5
Suppose you need a 30k  resistor but you only have a 27k 
and a handful of assorted resistors. What other resistor would you search
for and how would you connect them together?
55
Return to previous slide
Resistors in Series and Parallel - Answers
1
What is the combined resistance of a 39k  and a 47k  resistor
connected in series?
R total= R1 + R2 + R3
or
R = R1 + R2 + R3
So R = 39 000 + 47 000 = 86 000
= 86k
56
Return to menu slide
Resistors in Series and Parallel - Answers
2
What is the combined resistance of a 39k  and a 47k  resistor
connected in parallel?
1
RTotal
1
1
 
R1 R2
So 1/R = (1/39 000) +(1/47 000)
= 0.00002564 + 0.00002128 = 0.00004692
So R = 1/0.00004692 = 21 314
= 21.3k
= 22k
57
Return to menu slide
Resistors in Series and Parallel - Answers
3
What is the combined resistance of a 10 k, 20 k and 47 k
resistor connected in series?
R total= R1 + R2 + R3
or
R = R1 + R2 + R3
So R = 10 000 + 20 000 + 47 000
= 77 000 
= 77 k 
58
Return to menu slide
Resistors in Series and Parallel - Answers
4
What is the combined resistance of a 10k, 20k and 47k
resistor connected in parallel?
1
RTotal
1
1
1
 

R1 R2 R3
The numbers here could get very big so let us omit three zeros and give
the answer in k as all the resistances are in k anyway.
R = (1/10) +(1/20) +(1/47)
= 0.1000 + 0.0500 + 0.0213 = 0.1713
=5.84 k
Use 5.8 k
59
Return to menu slide
Resistors in Series and Parallel - Answers
5
Suppose you need a 30 k resistor but you only have a 27 k
and a handful of assorted resistors. What other resistor would you search
for and how would you connect them together?
You are looking to increase the resistance by adding another resistor.
This can only be done by adding a resistor in series.
R total= R1 + R2 + R3
or
R = R1 + R2 + R3
We know that Rtotal is 30 k and R1 is 27 k
So 30 = 27 + R2
R2 = 30 - 27
= 3 k
60
Return to menu slide
Capacitors
Capacitors store charge. The greater the
voltage that you apply to them, the greater the
charge that they store. In fact the ratio of the
charge stored to the voltage applied is called
the capacitance.
Capacitance = Charge / Voltage
or C = Q / V
Capacitance is measured in farad (F) but the farad is a large unit of
capacitance so you usually see microfarad F (millionth of a farad 10-6
or 0. 000 001 F), nanofarad nF (10-9) or picofarad pF (10-12).
The capacitor in the picture is a 470 F (0.000 47 F) polar (you must
connect it the correct way around in the circuit) capacitor rated at 40V
(the working voltage should not exceed 40V).
61
Return to main menu
Capacitors - Symbols
This is a non-polar capacitor it does not matter which way
around you place it in the
circuit.
This is a polar capacitor. It
is essential that the
capacitor is connected into
the circuit the correct way
around.
62
Return to previous slide
Capacitors
Capacitor Characteristics
Time Constant Calculations
Capacitors in Series
Capacitors in Parallel
Questions
63
Return to previous slide
Capacitor Characteristics
V
A
Closing the switch allows the capacitor
to charge. As this happens, the voltage
across the capacitor will rise in line
with the fall of current through it as it
becomes fully charged.
Voltage
Time
Current
Time
64
Return to menu slide
Capacitor Characteristics
V
A
The circuit has now been adapted so
that closing the switch allows the
capacitor to discharge through the
resistor. Note now that the current will
fall as the voltage falls.
Voltage
Time
Current
Time
65
Return to previous slide
Capacitor Characteristics
Y
X
The circuit on the left allows us to
investigate the charging and discharging
of a capacitor simply.
S
V
C
R
A
Connecting the flying lead S to point X
will charge the capacitor from the cell
through the resistor R.
Connecting the flying lead S to Y will
then discharge the capacitor through the
resistor.
It has been found that increasing either the capacitance or the
resistance will increase the time taken for the capacitor to charge.
66
Return to previous slide
Capacitor Characteristics
Y
X
When the flying lead S is connected to X, the
capacitor will charge up through the resistor.
S
V
C
R
A
At first there will be little or no charge in the
capacitor so the current flows into the
capacitor (via the resistor), quite rapidly.
The current through the resistor develops a
voltage over the resistor. The voltage across
the capacitor will be proportional to the
charge in it. Since the charging has only just
begun, it will be small but growing.
The capacitor begins to charge: It gets harder for more charge to flow
into the capacitor so the current decreases. As the charge on the
capacitor is increasing, the voltage across it increases too.
67
Return to previous slide
Capacitor Characteristics
Home
Y
X
S
V
C
Eventually the capacitor will “fill”. This
really means that it approaches the condition
such that the voltage across it is equal to the
supply voltage.
There will no longer be any current flowing.
R
A
The time taken to achieve this increases with
increased capacitance and /or resistance.
The capacitor is said to be fully charged..
Increasing the supply voltage makes no difference to the time taken
for the voltage across the capacitor to approach the voltage across the
supply.
68
Return to previous slide
Time Constant Calculations
The time constant is the time taken for:
the current or voltage to have fallen to 37% of its original value
or
the voltage to have risen to 63% of its original value
We can calculate the time constant for a circuit by multiplying the
capacitance of the capacitor by the resistance of the resistor:
T=CxR
The units of the time constant are seconds if the resistance is in ohms and
the capacitance in farads.
69
Return to menu
Time Constant Calculations
E.G. One
A 10M0 resistor is connected in series with a 470 pF capacitor. How long
will it take to discharge the capacitor to 37V from an initial voltage of
100V?
Note that the voltage is falling to 37% of its initial value, so we are
looking at one time constant.
Using T = C R
T = 0.000 000 000 470 x 10 000 000
= 0.004 7 s
70
Return to previous slide
Time Constant Calculations
Home
E.G. Two
A 10M0 resistor is connected in series with a capacitor. If the time
constant is 0.001s, what is the capacitance of the capacitor?
Using T = C R
0.001 = C x 10 000 000
C = 0.001 / 10 000 000
= 0.000 000 000 1 F
= 100 pF
71
Return to previous slide
Capacitors in Series
C1
C2
C3
These three capacitors are
connected in series. Their combined
capacitance is given by:
1
Ctotal
1

C1
1

C2
1

C3
or
CTotal

C1C2C3
C1  C2  C3
72
Return to menu
Capacitors in Series
Home
4
What is the combined capacitance of a 10 F, 20 F and 47 F
capacitor connected in series?
C1
C2
C3
CTotal

C1C2C3
C1  C2  C3
The numbers here could get very small so let us omit 5 zeros and give
the answer in F as all the capacitances are in F anyway.
C = (10 x 20 x 47) / (10 + 20 + 47)
= 9400 / 77
=122 F
73
Return to previous slide
Capacitors in Parallel
C1
These three capacitors are connected in
parallel with each other.
C2
C3
Note that because they are in parallel,
they must have the same voltage
across each other.
The combined capacitance of the network
of capacitances is given by:
Ctotal = C1 + C2 + C3
74
Return to menu
Capacitors in Parallel
Home
C1
Suppose that the capacitances are 10 F, 20
F and 47 F.
C2
Ctotal = C1 + C2 + C3
C3
So C = 10 + 20 + 47
= 77 F
75
Return to previous slide
Capacitors - Questions
1
What is the combined capacitance of a 10pF and a 20pF capacitor
connected in series?
2
What is the combined capacitance of a 10pF and a 20pF capacitor
connected in parallel?
3
What is the time constant for a 1000 pF capacitor connected to a
100k resistance?
4
What capacitance would you need to combine with a 200 F
capacitor to give the combinations a capacitance of 100 F? How would
you connect them together to achieve this?
5
What resistor could you connect with a 47 F capacitor to give a
time constant of 1.83 s ?
76
Return to previous slide
Capacitors - Answers
1
What is the combined capacitance of a 10pF and a 20pF capacitor
connected in series?
C1
C2
C3
CTotal

C1C2C3
C1  C2  C3
The numbers here could get very small so let us omit 11 zeros and give
the answer in pF as all the capacitances are in pF anyway.
C = (10 x 20) / (10 + 20)
= 200 / 30
=6.7 pF
77
Return to menu
Capacitors - Answers
2
What is the combined capacitance of a 10pF and a 20pF capacitor
connected in parallel?
C1
C2
Ctotal = C1 + C2 + C3
So C = 10 + 20
C3
= 30 pF
78
Return to menu
Capacitors - Answers
3
What is the time constant for a 1000 pF capacitor connected to a
100k resistance?
T=CxR
= (1000 x 0.000 000 000 001) x 100 000
= 0.000 1 s
79
Return to menu
Capacitors - Answers
4
What capacitance would you need to combine with a 200 F
capacitor to give the combinations a capacitance of 100 F? How would
you connect them together to achieve this?
In order to get a smaller capacitance, you need to connect them in series.
C1
C2
C3
CTotal

C1C2C3
C1  C2  C3
So 100 = 200 x C2 / (200 + C2)
100 (200 + C2) = 200C2
20 000 + 100C2 = 200C2
20 000 = 200C2 - 100C2
100 C2 = 20 000
C2 = 200 F
80
Return to menu
Capacitors - Answers
5
What resistor could you connect with a 47 F capacitor to give a
time constant of 1.83 s ?
T=CxR
1.83 = 0.000 047 x R
R = 1.83 / 0.000 047
= 38 936 
Use 39 k
81
Return to menu
Alternating Current
Direct current (DC) is the current that comes from a cell or battery.
It is unidirectional. That is to say that the net drift of electrons is in one
direction. This one direction will always be from positive to negative for
electrons but negative to positive for conventional flow.
It is easier to convert voltages from one value to another if the direction
of the current is rapidly changing.
This is called an alternating current (AC).
82
Return to main menu
Alternating Current
Alternating current has some strange properties:
•it can appear to pass through a capacitor
•it produces the discharges that you see in a plasma ball
•it can be stepped up (to higher voltages and lower current)
•it can be stepped down (to lower voltages and higher current)
Mains voltage is always due to an alternating current. It is used because
it can be stepped up or down easily.
83
Return to previous slide
Alternating Current
Throughout Europe, mains voltage is supplied at a frequency of 50 Hz.
You will remember that Hz is the abbreviation for hertz - the unit of
frequency.
This means that the electricity goes through one complete cycle 50 times
every second.
This means that the voltage will:
•start from zero and build up in one direction until it reaches a
maximum value (about 325 V).
•Fall back to zero
•Change direction and start to build up to a maximum value (about 325 V)
•Fall back to zero
•50 times per second
Alternating voltages (and currents) can have extremely high frequencies.
The current that produces radio waves can be many MHz (millions of
84
hertz).
Return to previous slide
Alternating Current - Questions
Home
1
What is the frequency of the mains voltage in the UK and
Europe?
2
What is the frequency of the mains voltage in the USA?
3
How long is a complete cycle of mains ac at 50 Hz?
4
How many times does the electricity in 50 Hz ac mains, change
direction?
5
Write out 250 MHz in full.
85
Return to previous slide
Alternating Current - Answers
Home
1
What is the frequency of the mains voltage in the UK and
Europe? 50Hz
2
What is the frequency of the mains voltage in the USA? 60Hz
3
How long is a complete cycle of mains ac at 50 Hz?
1/50th of a second = 0.02s
4
How many times does the electricity in 50 Hz ac mains, change
direction?
Twice each cycle so 100 times
5
Write out 250 MHz in full
250 000 000 hertz
86
Return to menu
Waveforms
As alternating currents and voltages vary with time, it is useful to have a
graphical representation of them.
The electronic device that does this for us is called an oscilloscope.
The essence of an oscilloscope is its ability to plot a graph for us,
showing the variation of voltage with time. It is particularly useful
because it works extremely quickly and it barely interferes with the
circuit from which you are taking the measurements.
When you first look at an oscilloscope, the number of knobs, levers and
buttons can be bewildering but you will soon get used to it. In fact, you
rarely need to use most of them.
87
Return to menu
Waveforms
Screen showing the trace
On / off switch
x input
The trace shows a graph with voltage on the y axis (vertical) and time on
the x axis (horizontal).
88
Return to previous slide
Waveforms
The waveform produced by mains voltage looks like this:
Voltage
time
This shape of waveform is called a sinusoidal wave.
89
Return to previous slide
Waveforms
The waveform produced by mains voltage looks like this:
Voltage
time
The arrows indicate a complete cycle. A cycle is the time that it takes to
reach the next adjacent identical position on the waveform.
90
Return to previous slide
Waveforms
The waveform produced by mains voltage looks like this:
Voltage
time
This arrow indicates the peak voltage. For mains it is about 325V in the
UK. The value of 230V that is quoted is the peak divided by the square
root of 2. (It is the dc equivalent voltage that would produce the same
heating effect as an ac with a peak voltage of 325V. Dividing by root 2
only works for sinusoidal waveforms). The peak voltage is the maximum
voltage.
91
Return to previous slide
Waveforms
The waveform produced by mains voltage looks like this:
Voltage
time
This arrow indicates the peak to peak voltage. Notice that the peak to
peak voltage is twice the peak voltage. For mains it is about 650V in the
UK and Europe.
92
Return to previous slide
Waveforms
Another common waveform called the square wave looks like this:
Voltage
time
The arrows indicate a complete cycle. A cycle is the time that it takes to
reach the next adjacent identical position on the waveform.
93
Return to previous slide
Waveforms
Another common waveform called the square wave looks like this:
Voltage
time
This arrow indicates the peak voltage.
94
Return to previous slide
Waveforms
Another common waveform called the square wave looks like this:
Voltage
time
This arrow indicates the peak to peak voltage. It will be twice the peak
voltage
95
Return to previous slide
Waveforms
Another common waveform called the saw-tooth wave looks like this:
Voltage
time
The arrows indicate a complete cycle. A cycle is the time that it takes to
reach the next adjacent identical position on the waveform.
96
Return to previous slide
Waveforms
Another common waveform called the saw-tooth wave looks like this:
Voltage
time
This arrow indicates the peak voltage.
97
Return to previous slide
Waveforms
Another common waveform called the saw-tooth wave looks like this:
Voltage
time
This arrow indicates the peak to peak voltage.
98
Return to previous slide
Waveforms - Questions
Home
1
What is the name of the
trace shown on the oscilloscope?
2
How many complete cycles
can you see?
3
If the scale on the y-axis is 2V per division, estimate the peak
voltage. What is the peak to peak voltage?
4
If the scale on the x-axis is 2ms per division, estimate the
length of a cycle.
5
Using your answer to question 4, calculate the frequency of
the wave.
99
Return to previous slide
Waveforms - Answers
1
What is the name of the
trace shown on the oscilloscope?
100
Return to menu
Waveforms - Answers
ONE
TWO THREE
2
How many complete cycles
can you see?
101
Return to menu
Waveforms - Answers
3
If the scale on the y-axis is
2V per division, estimate the peak
voltage. What is the peak to peak
voltage?
5 divisions
so 5 divisions x 2 V per division
= 10V
102
Return to menu
Waveforms - Answers
4
If the scale on the x-axis is
2ms per division, estimate the length
of a cycle.
Count as many complete cycles as you can to get as accurate an
answer as possible.
3 cycles is about 35 divisions
1 cycle is about 11.7 divisions
11.7 divisions is 11.7 x 2 ms
= 23.4 ms
103
Return to menu
Waveforms - Answers
5
Using your answer to question 4, calculate the frequency of the
wave.
From question 4 one cycle is about = 23.4 ms
23.4ms = 23.4 x 0.001s
= 0.0234s
How many of these can we get into 1 second?
= 1 / 0.0234
= 42.7 Hz
104
Return to menu
The Potential Divider
+9V
Voltage is sometimes referred to as
potential difference. The potential divider
simply divides up a potential or voltage.
In its simplest form it is two resistors
placed across a power supply. The voltage
across of each resistor is less than the
supply voltage. Adding the voltage across
each resistor will give the supply voltage.
It is probably easiest to understand if you
look at the diagram.
Here the power supply is 9V. Note that both
0V
the resistances are the same.
The voltage from the supply will be split (divided) equally as 4.5V. Of
course 4.5V + 4.5V = 9V.
105
Return to menu
The Potential Divider
2 000 
In this potential divider circuit, the
resistances are not the same.
It develops
The bigger resistance here It is 2/3rds 2/3rds of
means that there will be a of the
the
resistance. voltage.
bigger voltage here.
1 000 
It develops
The smaller resistance here It is 1/3rd 1/3rd of
of the
means that there will be a
the
resistance. voltage.
smaller voltage here.
+9V
0V
If you would like to work through this again, step back through
the sequence using the left arrow key.
106
Return to previous slide
The Potential Divider
+V
R1
V1
You can calculate the voltage across each
resistor using a formula too.
V1 = V x R1 / (R1 + R2)
V1 = 9 x 2 000 / (1 000 + 2000) = 9 x 2 / 3 = 6V
V2 = V x R2 / (R1 + R2)
R2
V2
V1 = 9 x 1 000 / (1 000 + 2000) = 9 x 1 / 3 = 3V
0V
107
Return to previous slide
The Potential Divider
The potential divider does not have to be made up of two fixed resistors.
One of them could be variable, or even both.
R1
R2
V1
V2
As R1 increases so does V1 but V2
will fall.
As R1 decreases so does V1 but V2
will rise.
It is just as if there is only one cake to
go around (the voltage). If R1
increases then V1gets more cake so
there is less left for V2!
108
Return to previous slide
The Potential Divider
Now the variable resistor has been moved to the lower position in the
network..
R1
R2
V1
V2
As R2 increases so does V2 but V1
will fall.
As R2 decreases so does V2 but V1
will rise.
It can be handy to change the position
of the variable resistor. Later you will
see that it can change the action of a
transistor circuit so make sure that
you follow it.
109
Return to previous slide
The Potential Divider
+V
R1
R2
With this potential divider, the “tap” in the
middle is a “slider”. It probably moves
along a track of carbon.
V1
V2
0V
R1 and V1 will be the resistance and
voltage “above” the slider.
R2 and V2 will be the resistance and
voltage “below” the slider.
As R1 increases, R2 decreases. This will
result in V1 increasing and V2 decreasing.
As R1 decreases, R2 increases. This will
result in V1 decreasing and V2 increasing.
110
Return to previous slide
The Potential Divider
Here is a component that could be used as a potential divider.
The black ring is
the carbon track.
You adjust it by
putting a
screwdriver in
here and turning
the outer metal
ring.
111
Return to previous slide
The Potential Divider
Here is another:
You adjust it by
putting a
screwdriver in
here and turning
the outer metal
ring.
112
Return to previous slide
The Potential Divider
It is possible to use many different components that vary their resistance
in a potential divider circuit. Here are a few that you might find and the
physical conditions that change their resistance.
Light Dependent Resistor (LDR) - decreases resistance with increased
illumination.
Thermistor - decreases its resistance with increased temperature
(negative temperature coefficient).
Microphone - changes resistance with sound.
Strain gauge - changes its resistance when stressed.
Photodiode - decreases resistance with increased illumination.
113
Return to previous slide
The Potential Divider - Questions
Home
1
A 2k and a 3k resistor are used in potential divider using a 10V
supply. Sketch a possible set up and label the resistors and the voltages
across them.
Answer
2
Suggest two possible fixed resistors that could be used to obtain
3V from a 15V supply. Answer
3
A 27k and a 62k resistor are used in potential divider using a
12V supply. Sketch a possible set up and label the resistors and the
voltages across them.
Answer
4
A 15V supply is attached across a potential divider. If one of the
resistors is a 390k and there is a voltage of 9V across the other, what is
the second resistance?
Answer
5
A potential divider is created from a fixed resistor and an LDR.
Explain how the network produces different voltages.
114
Answer
Return to previous slide
The Potential Divider - Answers
1
A 2k and a 3k resistor are used in potential divider using a 10V
supply. Sketch a possible set up and label the resistors and the voltages
across them.
+10V
R1 = 2 000 
V1 = V x R1 / (R1 + R2)
V1= 4V
V1 = 10 x 2 000 / (3 000 + 2000) = 10 x 2 / 5 = 4V
R2 = 3 000 
V2 = V x R2 / (R1 + R2)
V2 = 6V
V1 = 10 x 3 000 / (3 000 + 2000) = 10 x 3 / 5 = 6V
0V
115
Return to menu
The Potential Divider - Answers
2
Suggest two possible fixed resistors that could be used to obtain
3V from a 15V supply.
V1 = V x R1 / (R1 + R2)
So 3 = 15 x R1 / (R1 + R2)
We could use more or less any combination. However, they should be
quite high so that they do not drain a lot of current.
Let us choose R1 as being 100k.
3 = 15 x 100 / (100 +R2)
3(100 + R2) = 1 500
300 + 3R2 = 1 500
3R2 = 1 500 - 300 = 1 200
R2 = 1 200 / 3 = 400k.
116
Return to menu
The Potential Divider - Answers
3
A 27k and a 62k resistor are used in potential divider using a
12V supply. Sketch a possible set up and label the resistors and the
voltages across them.
+12V
R1 = 27k
V1 = V x R1 / (R1 + R2)
V1= 3.64V
V1 = 12 x 27 / (27 + 62) = 12 x 27 / 89 = 3.64V
R2 = 62k
V2 = V x R2 / (R1 + R2)
V2 = 8.36V
V1 = 12 x 62 / (27 + 62) = 12 x 62 / 89 = 8.36V
0V
117
Return to menu
The Potential Divider - Answers
4
A 15V supply is attached across a potential divider. If one of the
resistors is a 390k and there is a voltage of 9V across the other, what is
the second resistance?
So V1 = 15 - 9 = 6V
V1 = V x R1 / (R1 + R2)
Now 6 = 15 x R1 / (R1 +390)
6 (R1 + 390) = 15 R1
6 R1 + 2 340 = 15 R1
9R1 = 2 340
R1 = 2 340 / 9 = 260k so use 270k
118
Return to menu
The Potential Divider - Answers
5
A potential divider is created from a fixed resistor and an LDR.
Explain how the network produces different voltages.
In bright illumination the LDR’s resistance falls. The voltage across the
LDR will consequently fall while the voltage across the fixed resistance
will rise.
As it goes dark, the LDR’s resistance will increase, increasing the
voltage across the LDR. As this happens, the voltage across the resistor
will fall.
119
Return to menu
Transistor Circuits
The transistor is a three connection component that can be used either as
an amplifier or a switch.
+V
collector
base
+0.7V
emitter
0V
Essentially the circuit is set up so as to try to force electrons through the
emitter and out of the collector. This might be to light a bulb.
However, under normal circumstances, there is a very high resistance
between the emitter and the collector so the bulb will not light.
If we make the base go positive, the collector / emitter junction conducts
120
and the bulb will light.
Return to menu
Transistor Circuits
The clever part now is to control the base bias voltage that turns the
transistor on.
+V
The base bias voltage is the voltage between
the base and the emitter. If it is anything
much less that 0.7V, the transistor will be off.
c
b
The transistor switches
Rb
on when it is 0.7V.
You should never allow the base bias voltage
to get too high as this will overheat the base
and burn out the transistor. For this reason
you will frequently find a resistor connected
to the base.
e
0V
121
Return
Transistor Circuits
The clever part now is to control the base bias voltage that turns the
transistor on.
+V
This can be achieved
using a potential divider.
R1
Correct selection of the
two resistors R1 and R2
c
will take the base to
b
Rb
0.7V and turn the
transistor on.
R2
e
Suppose R2 was much
higher than R1. The
voltage across R2 would
0V
be high so the transistor
122
would switch on.
Return
Transistor Circuits
The clever part now is to control the base bias voltage that turns the
transistor on.
Now suppose R2 was an
+V
LDR.
R1
In the bright light, its
resistance would be low
c
so the voltage across it
b
Rb
would be low, the
transistor switched off
R2
e
and the lamp off.
But suppose that it
now goes dark!
0V
123
Return
Transistor Circuits
The clever part now is to control the base bias voltage that turns the
transistor on.
+V
It has just gone dark!
R1
The resistance of the
LDR rises.
c
b
Rb
The voltage across the
LDR rises.
R2
e
The base bias voltage
reaches 0.7V
0V
The transistor
124
switches on. The bulb lights.
Return
Transistor Circuits
The clever part now is to control the base bias voltage that turns the
transistor on.
+V
Suppose that we now
R1
swap the positions of
the resistor and the
LDR.
c
b
Rb
The bulb will now come
R2
e
on in daylight! It might
be useful as a warning
light circuit in certain
0V
circumstances.
125
Return
Transistor Circuits
The clever part now is to control the base bias voltage that turns the
transistor on.
+V
Now let us consider:
R1
•Ib the base current
Ic
I
b
that flows into the
c
transistor
b
•Ie the emitter
Rb
current that flows
R2
out of the transistor
e
•IC the collector
Ie
current that flows
0V
into the transistor
Ie = I b + I c
126
Return
Transistor Circuits
The clever part now is to control the base bias voltage that turns the
transistor on.
+V
I =I +I
e
b
c
The base current will
be very small as it has
passed through R1 and
Rb so it is almost true
that Ie = Ic.
The ratio of Ic : Ib is
important. It shows
that the transistor is
amplifying. It is often
around about 100.
R1
Ic
Ib
Rb
R2
b
c
e
Ie
0V
127
Return
Transistor Circuits
The clever part now is to control the base bias voltage that turns the
transistor on.
+V
I =I +I
e
b
c
That is to say that the
collector current is a
always a constant
amount bigger than
the base current.
Feed a small current
to the base and you
get a big current in
the collector.
R1
Ic
Ib
Rb
R2
b
c
e
Ie
0V
128
Return
Transistor Circuits
The clever part now is to control the base bias voltage that turns the
transistor on.
+V
I =I +I
e
b
c
The ratio is called hfe.
R1
Ic
Ib
hfe = Ic / Ib
Rb
R2
b
c
e
Ie
0V
129
Return
Transistor Circuits
Click on a
component to find
out what it does.
+V
Relay
R1
Rb
R2
b
c
e
C1
0V
CONTINUE
130
Return
Transistor Circuits
Capacitor
This stores charge. It
acts as a time delay
to any switching. If
the transistor is on
and tries to go off, it
will act as a reservoir
and keep the
transistor on for a
while longer.
Click on a
component to find
out what it does.
+V
Relay
R1
Rb
R2
b
c
e
C1
0V
CONTINUE
131
Return
Transistor Circuits
LDR Light
Dependent Resistor
Its resistance
decreases with
increased
illumination. In the
dark, the resistance
goes up turning the
transistor on.
Click on a
component to find
out what it does.
+V
Relay
R1
Rb
R2
b
c
e
C1
0V
CONTINUE
132
Return
Transistor Circuits
Base Bias Resistor
This fixed resistor
protects the base
from too much
current.
Click on a
component to find
out what it does.
+V
Relay
R1
Rb
R2
b
c
e
C1
0V
CONTINUE
133
Return
Transistor Circuits
Potential Divider
The LDR and R2 are
a potential divider.
Click on a
component to find
out what it does.
+V
Relay
R1
Rb
R2
b
c
e
C1
0V
CONTINUE
134
Return
Transistor Circuits
Transistor
A small voltage at
the base will allow
current to flow
through the emitter
from the collector.
Click on a
component to find
out what it does.
+V
Relay
R1
Rb
R2
b
c
e
C1
0V
CONTINUE
135
Return
Transistor Circuits
Diode - this only
allows current to
flow in the direction
of the arrow head.
Rapid changes in the
magnetic field of the
relay can cause high
voltage that would
damage the
transistor.
The diode
diverts the
currents C1
formed by
this
process.
Click on a
component to find
out what it does.
+V
Relay
R1
Rb
R2
b
c
e
0V
CONTINUE
136
Return
Transistor Circuits
Relay - current
through the relay
produces a magnetic
field that throws a
switch in another
external circuit. The
external circuit can
be a much higher
powered circuit.
Click on a
component to find
out what it does.
+V
Relay
R1
Rb
R2
b
c
e
C1
0V
CONTINUE
137
Return
Transistor Circuits - Questions
1
The collector current in a circuit is 120mA when the base current
is 3mA. What is hfe and the emitter current?
2
Why do we connect a resistor directly to the base of the
transistor?
3
Sketch a circuit that will throw a relay in the dark that in turn will
turn on a switch.
4
Why should a diode be connected across a relay in the collector
circuit of a network?
5
Explain what happens when the resistance of the base bias
resistor falls in a transistor circuit controlling a motor.
Answers:
1
2
3
4
5
138
Return to previous slide
Transistor Circuits - Answers
1
The collector current in a circuit is 120mA when the base current
is 3mA. What is hfe and the emitter current?
hfe = Ic / Ib
= 120 / 3
= 40
139
Return to menu
Transistor Circuits - Answers
2
Why do we connect a resistor directly to the base of the
transistor?
The resistor limits the current entering the base. This stops the base from
overheating due to excessive currents which would burn the transistor
out.
140
Return to menu
Transistor Circuits - Answers
3
Sketch a circuit that will throw a relay in the dark that in turn will
turn on a switch.
+V
Relay
R1
b
c
e
C1
LDR
0V
141
Return to menu
Transistor Circuits - Answers
4
Why should a diode be connected across a relay in the collector
circuit of a network?
The relay can create large voltages due to rapid changes in magnetic
fields as they switch off. The diode provides a short circuit for the
current due to this voltage. As diodes only carry current in one direction,
the diode connected to the relay will have no effect in normal operation
of the relay.
142
Return to menu
Transistor Circuits - Answers
5
Explain what happens when the resistance of the base bias
resistor falls in a transistor circuit controlling a motor.
As the resistance falls, so will the voltage across it.
The voltage across the base will consequently fall.
This will turn off the transistor.
The collector current will fall to zero (or extremely close to zero).
The motor will switch off.
143
Return to menu
Electronics Questions
1
What is the nominal value and tolerance of this resistor?
2
A power supply drives a current of 150mA through a bulb with a
working resistance of 10. What voltage is the power supply?
3
What is the current passing through a heater that dissipates 40W
when a voltage of 10V is applied across it?
144
Return to menu
Electronics Questions
4
What is the combined resistance of a 30k , 20k  and 47k 
resistor connected in parallel?
5
Suppose you need a 50k  resistor but you only have a 47k 
and a handful of assorted resistors. What other resistor would you search
for and how would you connect them together?
6
What is the combined capacitance of a 47pF and a 20pF capacitor
connected in series?
7
What is the combined capacitance of a 47pF and a 20pF capacitor
connected in parallel?
8
What is the time constant for a 1000 F capacitor connected to a
10M resistance?
145
Return to previous slide
Electronics Questions
9
If the scale on the y-axis is 4mV per division, estimate the
peak voltage. What is the peak to peak voltage?
10
If the scale on the x-axis is 50 s per division, estimate the
length of a cycle. Using your answer, calculate the frequency of the
wave.
146
Return to previous slide
Return to main menu
147
Return to previous slide
Electronics Answers
1
What is the nominal value and tolerance of this resistor?
This gold band indicates that the tolerance
of the resistor is ±5% (plus or minus 5 percent).
The third band is black. This means that there are no zeros.
The second band is green. This means the second digit is 5.
The first band is violet. This means the first digit is 7.
148
So the resistor is nominally 75 .
Return to menu
Electronics Answers
2
A power supply drives a current of 150mA through a bulb with a
working resistance of 10. What voltage is the power supply?
V=IxR
so V = 0.15 x 10
=1.5 V
149
Return to menu
Electronics Answers
3
What is the current passing through a coil that dissipates 40W
when a voltage of 10V is applied across it?
P = IV
So I = P / V
= 40 / 10
=4W
150
Return to menu
Electronics Answers
4
What is the combined resistance of a 30k, 20k and 47k
resistor connected in parallel?
RTotal

R1 R2 R3
R1  R2  R3
The numbers here could get very big so let us omit three zeros and give
the answer in k as all the resistances are in k anyway.
R = (30 x 20 x 47) / (30 + 20 + 47)
= 28 200 / 97
=291 k
Use 300 k
151
Return to menu
Electronics Answers
5
Suppose you need a 50 k resistor but you only have a 47 k
and a handful of assorted resistors. What other resistor would you search
for and how would you connect them together?
You are looking to increase the resistance by adding another resistor.
This can only be done by adding a resistor in series.
R total= R1 + R2 + R3
or
R = R1 + R2 + R3
We know that Rtotal is 50 k and R1 is 47 k
So 50 = 47 + R2
R2 = 50 - 47
= 3 k
152
Return to menu
Electronics Answers
6
What is the combined capacitance of a 47pF and a 20pF capacitor
connected in series?
C1
C2
C3
CTotal

C1C2C3
C1  C2  C3
The numbers here could get very small so let us omit 11 zeros and give
the answer in pF as all the capacitances are in pF anyway.
C = (47 x 20) / (47 + 20)
= 940 / 67
=14 pF
153
Return to menu
Electronics Answers
7
What is the combined capacitance of a 47pF and a 20pF capacitor
connected in parallel?
C1
C2
Ctotal = C1 + C2 + C3
So C = 47 + 20
C3
= 67 pF
154
Return to menu
Electronics Answers
8
What is the time constant for a 1000 F capacitor connected to a
10M resistance?
T=CxR
= (1000 x 0.000 001) x 10 000 000
= 10 000 s
155
Return to menu
Electronics Answers
9
If the scale on the y-axis is
4mV per division, estimate the
peak voltage. What is the peak to
peak voltage?
5 divisions
so 5 divisions x 4mV per division
= 20mV
156
Return to menu
Electronics Answers
10
If the scale on the x-axis is 50
s per division, estimate the length of
a cycle.
Count as many complete cycles as you can to get as accurate an answer
as possible.
3 cycles is about 35 divisions
1 cycle is about 11.7 divisions
11.7 divisions is 11.7 x 2 s
= 23.4 s
157
Electronics Answers
10 continued Using your previous answer, calculate the frequency of
the wave.
From question 4 one cycle is about = 23.4 s
23.4 s = 23.4 x 0.000 001s
= 0.000 023 4s
How many of these can we get into 1 second?
= 1 / 0.000 023 4s
= 42.7 kHz
158
Return to menu
Introduction
Ohm’s Law
Power Calculations
Resistors in Series and Parallel
Home
Capacitors
Alternating Current
Waveforms
Transistor Circuits
The Potential Divider
Components
Questions
159
Return to previous slide