Download Capacitors and Inductors

Document related concepts
no text concepts found
Transcript
Capacitors and Inductors
Chapter 6
Chap. 6, Capacitors and Inductors
•
•
•
•
•
Introduction
Capacitors
Series and Parallel Capacitors
Inductors
Series and Parallel Inductors
Ch06 Capacitors and Inductors
2
6.1 Introduction
•
•
Resistor: a passive element which dissipates
energy only
Two important passive linear circuit
elements:
1) Capacitor
2) Inductor
•
Capacitor and inductor can store energy
only and they can neither generate nor
dissipate energy.
Ch06 Capacitors and Inductors
3
Michael Faraday (1971-1867)
Ch06 Capacitors and Inductors
4
6.2 Capacitors
• A capacitor consists of two conducting plates
separated by an insulator (or dielectric).
C
εA
d
   r 0
 0  8.854 10 12 (F/m)
Ch06 Capacitors and Inductors
5
•
εA
C
d
Three factors affecting the value of
capacitance:
1. Area: the larger the area, the greater the
capacitance.
2. Spacing between the plates: the smaller the
spacing, the greater the capacitance.
3. Material permittivity: the higher the permittivity,
the greater the capacitance.
Ch06 Capacitors and Inductors
6
Fig 6.4
(a) Polyester capacitor, (b) Ceramic capacitor, (c) Electrolytic capacitor
Ch06 Capacitors and Inductors
7
Fig 6.5
Variable capacitors
Ch06 Capacitors and Inductors
8
Fig 6.3
Ch06 Capacitors and Inductors
9
Fig 6.2
Ch06 Capacitors and Inductors
10
Charge in Capacitors
• The relation between the charge in plates and
the voltage across a capacitor is given below.
q  Cv
1F  1 C/V
q
Linear
Nonlinear
v
Ch06 Capacitors and Inductors
11
Voltage Limit on a Capacitor
• Since q=Cv, the plate charge increases as the
voltage increases. The electric field intensity
between two plates increases. If the voltage
across the capacitor is so large that the field
intensity is large enough to break down the
insulation of the dielectric, the capacitor is out
of work. Hence, every practical capacitor has a
maximum limit on its operating voltage.
Ch06 Capacitors and Inductors
12
I-V Relation of Capacitor
+
i
v
C
dq
dv
q  Cv, i 
C
dt
dt
-
Ch06 Capacitors and Inductors
13
Physical Meaning
dv
iC
dt
+
v
i
C
-
• when v is a constant voltage, then i=0; a constant
voltage across a capacitor creates no current through
the capacitor, the capacitor in this case is the same as
an open circuit.
• If v is abruptly changed, then the current will have an
infinite value that is practically impossible. Hence, a
capacitor is impossible to have an abrupt change in
its voltage except an infinite current is applied.
Ch06 Capacitors and Inductors
14
Fig 6.7
• A capacitor is an open circuit to dc.
• The voltage on a capacitor cannot change
abruptly.
Abrupt change
Ch06 Capacitors and Inductors
15
dv
iC
dt
1 t
v(t )   idt
C 
1 t
v(t )   idt  v(to)
C to
 v()  0 
 v(to)  q(to) / C 
+
v
i
C
-
• The charge on a capacitor is an integration of
current through the capacitor. Hence, the
memory effect counts.
Ch06 Capacitors and Inductors
16
Energy Storing in Capacitor
dv
p  vi  Cv
dt
v (t )
dv
1 2
w   pdt  C  v dt  C v (  ) vdv  Cv
dt
2
t
t
1
w(t )  Cv 2 (t )
2
q 2 (t )
w(t ) 
2C
Ch06 Capacitors and Inductors
( v( )  0)
+
v
v (t )
v (  )
i
C
-
17
Model of Practical Capacitor
Ch06 Capacitors and Inductors
18
Example 6.1
(a) Calculate the charge stored on a 3-pF
capacitor with 20V across it.
(b) Find the energy stored in the capacitor.
Ch06 Capacitors and Inductors
19
Example 6.1
Solution:
(a) Since q  Cv,
q  3  10
12
 20  60pC
(b) The energy stored is
1 2 1
12
w  Cv   3  10  400  600pJ
2
2
Ch06 Capacitors and Inductors
20
Example 6.2
• The voltage across a 5- F capacitor is
v(t )  10 cos 6000t V
Calculate the current through it.
Solution:
• By definition, the current is
dv
6 d
iC
 5 10
(10 cos 6000t )
dt
dt
 5  10 6  6000 10 sin 6000t  0.3 sin 6000t A
Ch06 Capacitors and Inductors
21
Example 6.3
• Determine the voltage across a 2-F capacitor if the
current through it is
i(t )  6e
3000t
mA
Assume that the initial capacitor voltage is zero.
Solution:
• Since v  1 t idt  v(0) and v(0)  0,

C 0
3
t
1
3000 t
3  10 3000t t
3
v
6
e
dt  10 
e
6 0
0
2  10
 3000
 (1  e 3000t )V
Ch06 Capacitors and Inductors
22
Example 6.4
• Determine the current through a 200- F
capacitor whose voltage is shown in Fig 6.9.
Ch06 Capacitors and Inductors
23
Example 6.4
Solution:
• The voltage waveform can be described
mathematically as
50t V
0  t 1

 100  50t V
1 t  3
v(t )  
 200  50t V
3t  4

0 otherwise

Ch06 Capacitors and Inductors
24
Example 6.4
• Since i = C dv/dt and C = 200 F, we take the
derivative of to obtain
0  t  1  10mA
0  t 1
 50
 50
1  t  3  10mA
1 t  3
6
i (t )  200  10  

50
3t  4
10mA
3t  4


0 otherwise
 0 otherwise 
• Thus the current waveform is shown in
Fig.6.10.
Ch06 Capacitors and Inductors
25
Example 6.4
Ch06 Capacitors and Inductors
26
Example 6.5
• Obtain the energy stored in each capacitor in
Fig. 6.12(a) under dc condition.
Ch06 Capacitors and Inductors
27
Example 6.5
Solution:
• Under dc condition, we replace each capacitor
with an open circuit. By current division,
3
i
(6mA )  2mA
3 2 4
 v1  2000 i  4 V, v 2  4000i  8 V
1
1
2
3
2
 w1  C1v1  (2  10 )(4)  16mJ
2
2
1
1
2
3
2
w2  C2 v2  (4  10 )(8)  128mJ
2
2
Ch06 Capacitors and Inductors
28
Fig 6.14
Ceq  C1  C2  C3  ....  C N
Ch06 Capacitors and Inductors
29
6.3 Series and Parallel Capacitors
i  i1  i2  i3  ...  iN
dv
dv
dv
dv
i  C1  C2  C3  ...  C N
dt
dt
dt
dt
N
dv
dv


   CK   Ceq
dt
 k 1  dt
Ceq  C1  C2  C3  ....  CN
• The equivalent capacitance of N parallelconnected capacitors is the sum of the
individual capacitance.
Ch06 Capacitors and Inductors
30
Fig 6.15
1
1
1
1
1
 
  ... 
Ceq C1 C2 C3
CN
Ch06 Capacitors and Inductors
31
Series Capacitors
v(t )  v1 (t )  v2 (t )  ...  vN (t )
1
Ceq
1
1
1
1 t
id  ( C1  C2  C3  ...  CN )id
t
q(t ) q(t ) q(t )
q(t )



Ceq
C1
C2
CN
• The equivalent capacitance of seriesconnected capacitors is the reciprocal of the
sum of the reciprocals of the individual
capacitances.
C1C2
1
1 1
Ceq 
 
C1  C2
Ceq C1 C2
Ch06 Capacitors and Inductors
32
Summary
• These results enable us to look the capacitor in
this way: 1/C has the equivalent effect as the
resistance. The equivalent capacitor of
capacitors connected in parallel or series can
be obtained via this point of view, so is the Y△ connection and its transformation
Ch06 Capacitors and Inductors
33
Example 6.6
• Find the equivalent capacitance seen between
terminals a and b of the circuit in Fig 6.16.
Ch06 Capacitors and Inductors
34
Example 6.6
Solution:
 20  F and 5  F capacitors are in series :
20  5

 4F
20  5
 4  F capacitor is in parallel with the 6  F
and 20  F capacitors :
 4  6  20  30 F
 30  F capacitor is in series with
the 60  F capacitor.
30  60
Ceq 
F  20F
30  60
Ch06 Capacitors and Inductors
35
Example 6.7
• For the circuit in Fig 6.18, find the voltage
across each capacitor.
Ch06 Capacitors and Inductors
36
Example 6.7
Ch06 Capacitors and Inductors
37
Example 6.7
Solution:
• Two parallel capacitors:
 Ceq 
• Total charge
1
1 1 1
 
60 30 20
mF  10mF
3
q  Ceq v  10  10  30  0.3 C
• This is the charge on the 20-mF and 30-mF capacitors,
because they are in series with the 30-v source. ( A
crude way to see this is to imagine that charge acts
like current, since i = dq/dt)
Ch06 Capacitors and Inductors
38
Example 6.7
q
0
.
3
• Therefore,
v1  
 15 V,
3
C1 20  10
q
0.3
v2 

 10 V
3
C2 30  10
• Having determined v1 and v2, we now use KVL to
determine v3 by
v3  30  v1  v2  5V
• Alternatively, since the 40-mF and 20-mF capacitors
are in parallel, they have the same voltage v3 and their
combined capacitance is 40+20=60mF.
Ch06 Capacitors and Inductors
q
0.3
 v3 

 5V
3
60mF 60  10
39
Joseph Henry (1979-1878)
Ch06 Capacitors and Inductors
40
6.4 Inductors
• An inductor is made of a coil of conducting wire
N A
L
l
2
Ch06 Capacitors and Inductors
41
Fig 6.22
N 2 A
L
l
   r 0
 0  4 10 7 (H/m)
N : number of turns.
l :length.
A:cross  sectional area.
 : permeability of the core
Ch06 Capacitors and Inductors
42
Fig 6.23
(a) air-core
(b) iron-core
(c) variable iron-core
Ch06 Capacitors and Inductors
43
Flux in Inductors
• The relation between the flux in inductor and
the current through the inductor is given below.
  Li
ψ
1H  1 Weber/A
Linear
Nonlinear
i
Ch06 Capacitors and Inductors
44
Energy Storage Form
• An inductor is a passive element designed to
store energy in the magnetic field while a
capacitor stores energy in the electric field.
Ch06 Capacitors and Inductors
45
I-V Relation of Inductors
• An inductor consists of
a coil of conducting
d
wire.
di
v
L
dt
dt
i
+
v
L
-
Ch06 Capacitors and Inductors
46
Physical Meaning
d
di
v
L
dt
dt
• When the current through an inductor is a constant,
then the voltage across the inductor is zero, same as a
short circuit.
• No abrupt change of the current through an inductor
is possible except an infinite voltage across the
inductor is applied.
• The inductor can be used to generate a high voltage,
for example, used as an igniting element.
Ch06 Capacitors and Inductors
47
Fig 6.25
• An inductor are like a short circuit to dc.
• The current through an inductor cannot change
instantaneously.
Ch06 Capacitors and Inductors
48
1
di  vdt
L
1 t
i   v(t )dt
L 
1 t
i   v(t )dt  i (to )
L to
+
v
L
-
The inductor has memory.
Ch06 Capacitors and Inductors
49
Energy Stored in an Inductor
 di 
P  vi   L  i
 dt 
+
v
L
di


w   pdt    L idt
 dt 
i (t )
1 2
1 2
 L i (  ) i di  Li (t )  Li () i ()  0,
2
2
t
t
• The energy stored in an inductor
1 2
w(t )  Li (t )
2
Ch06 Capacitors and Inductors
50
Model of a Practical Inductor
Ch06 Capacitors and Inductors
51
Example 6.8
• The current through a 0.1-H inductor is i(t) =
10te-5t A. Find the voltage across the inductor
and the energy stored in it.
Solution:
di
Since v  L and L  0.1H,
dt
d
v  0.1 (10te 5t )  e 5t  t (5)e 5t  e 5t (1  5t )V
dt
The energy stored is
1 2 1
w  Li  (0.1)100t 2 e 10t  5t 2 e 10t J
2
2
Ch06 Capacitors and Inductors
52
Example 6.9
• Find the current through a 5-H inductor if the
voltage across it is
2
30t , t  0
v(t )  
t0
 0,
Also find the energy stored within 0 < t < 5s.
Assume i(0)=0.
Solution:
1 t
Since i  t v(t )dt  i (t0 ) and L  5H.
L
3
t
1
t
2
i  0 30t dt  0  6   2t 3 A
3
5
0
Ch06 Capacitors and Inductors
53
Example 6.9
The power p  vi  60t 5 , and the energy stored is then
6
t 5
w   pdt  0 60t dt  60
 156.25 kJ
60
Alternatively, we can obtain the energy stored using
Eq.(6.13), by writing
1 2
1
w(5)  w(0)  Li (5)  Li (0)
2
2
1
3 2
 (5)(2  5 )  0  156.25 kJ
2
as obtained before.
5
Ch06 Capacitors and Inductors
5
54
Example 6.10
• Consider the circuit in
Fig 6.27(a). Under dc
conditions, find:
(a) i, vC, and iL.
(b) the energy stored
in the capacitor and
inductor.
Ch06 Capacitors and Inductors
55
Example 6.10
Solution:
(a ) Under dc condition : capacitor  open circuit
inductor  short circuit
12
i  iL 
 2 A, vc  5i  10 V
1 5
(b )
1
1
2
wc  Cvc  (1)(10 )  50J,
2
2
1 2 1
wL  Li  (2)(2 2 )  4J
2
2
Ch06 Capacitors and Inductors
2
56
Inductors in Series
Leq  L1  L2  L3  ...  LN
Ch06 Capacitors and Inductors
57
Inductors in Parallel
1
1 1
1
  
Leq L1 L2
LN
Ch06 Capacitors and Inductors
58
6.5 Series and Parallel Inductors
• Applying KVL to the loop,
v  v1  v2  v3  ...  vN
• Substituting vk = Lk di/dt results in
di
di
di
di
v  L1  L2  L3  ...  LN
dt
dt
dt
dt
di
 ( L1  L2  L3  ...  LN )
dt
N
di
di


   LK   Leq
dt
 K 1  dt
Leq  L1  L2  L3  ...  LN
Ch06 Capacitors and Inductors
59
Parallel Inductors
• Using KCL, i  i1  i2  i3  ...  iN
• But ik  1 tt vdt  ik (t0 )
Lk
1
i 
Lk
t
t
0
o
1
1 t
vdt  i1 (t0 )  t vdt  is (t0 )  ... 
LN
L2
0
t
t vdt  iN (t0 )
0
1 1
1 t
    ...   t vdt  i1 (t0 )  i2 (t0 )  ...  iN (t0 )
LN 
 L1 L2
0
N
N 1t
1 t
    t vdt   ik (t0 ) 
vdt  i (t0 )

t
Leq
k 1
 k 1 Lk 
0
Ch06 Capacitors and Inductors
0
60
• The inductor in various connection has the
same effect as the resistor. Hence, the Y-Δ
transformation of inductors can be similarly
derived.
Ch06 Capacitors and Inductors
61
Table 6.1
Ch06 Capacitors and Inductors
62
Example 6.11
• Find the equivalent inductance of the circuit
shown in Fig. 6.31.
Ch06 Capacitors and Inductors
63
Example 6.11
• Solution:
Series : 20H, 12H, 10H
 42H
7  42
 6H
Parallel :
7  42
 Leq  4  6  8  18H
Ch06 Capacitors and Inductors
64
Practice Problem 6.11
Ch06 Capacitors and Inductors
65
Example 6.12
• Find the circuit in Fig. 6.33, i (t )  4(2  e
If i2 (0)  1 mA, find : (a) i (0)
(b) v(t ), v1 (t ), and v2 (t ); (c) i1 (t ) and i2 (t )
10t
)mA.
1
Ch06 Capacitors and Inductors
66
Example 6.12
Solution:
10 t
(a ) i(t )  4(2  e )mA  i(0)  4(2  1)  4mA.
 i1 (0)  i (0)  i2 (0)  4  (1)  5mA
(b) The equivalent inductance is
Leq  2  4 || 12  2  3  5H
di
10 t
10 t
 v(t )  Leq  5(4)(1)(10)e mV  200e mV
dt
di
10 t
10 t
v1 (t )  2  2(4)(10)e mV  80e mV
dt
10 t
 v2 (t )  v(t )  v1(t )  120e mV
Ch06 Capacitors and Inductors
67
Example 6.12
1 t
(c) i  0 v(t ) dt  i (0) 
L
1 t
120 t 10t
i1 (t )  0 v2 dt  i1 (0) 
e
dt

5
mA

4
4 0
10 t t
 3e
 5 mA  3e 10t  3  5  8  3e 10t mA
0
1 t
120 t 10t
i2 (t )  0 v2 dt  i2 (0) 
e dt  1mA

0
12
12
10 t t
 e
 1mA  e 10t  1  1  e 10t mA
0
Note that i1 (t )  i2 (t )  i (t )
Ch06 Capacitors and Inductors
68