* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download EEE 302 Lecture 19 - Universitas Udayana
Audio crossover wikipedia , lookup
Oscilloscope history wikipedia , lookup
Analog-to-digital converter wikipedia , lookup
Regenerative circuit wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Integrating ADC wikipedia , lookup
Transistor–transistor logic wikipedia , lookup
Superheterodyne receiver wikipedia , lookup
Equalization (audio) wikipedia , lookup
Current mirror wikipedia , lookup
Power electronics wikipedia , lookup
Valve audio amplifier technical specification wikipedia , lookup
Wilson current mirror wikipedia , lookup
Schmitt trigger wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Standing wave ratio wikipedia , lookup
Operational amplifier wikipedia , lookup
Index of electronics articles wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Wien bridge oscillator wikipedia , lookup
RLC circuit wikipedia , lookup
Phase-locked loop wikipedia , lookup
Radio transmitter design wikipedia , lookup
Mathematics of radio engineering wikipedia , lookup
Valve RF amplifier wikipedia , lookup
Network analysis (electrical circuits) wikipedia , lookup
Opto-isolator wikipedia , lookup
Complex Waveforms as Input When complex waveforms are used as inputs to the circuit (for example, as a voltage source), then we (1) must Laplace transform the inputs (2) determine the transfer function (3) feed the input through the transfer function The transfer function, H(s), is the ratio of some output variable to some input variable Y ( s) Output H ( s) X( s ) Input 1 Lecture 19 Transfer Function The transfer function, H(s), is Y ( s) Output H ( s) X( s ) Input All initial conditions are zero (makes transformation step easy) Can use transfer function to find output to an arbitrary input Y(s) = H(s) X(s) The impulse response is the inverse Laplace transform of transfer function h(t) = L-1[H(s)] with knowledge of the transfer function or impulse response, we can find response of circuit to any input 2 Lecture 19 Variable-Frequency Response Analysis As an extension of ac analysis, we now vary the frequency and observe the circuit behavior Graphical display of frequency dependent circuit behavior can be very useful; however, quantities such as the impedance are complex valued such that we will tend to graph the magnitude of the impedance versus frequency (i.e., |Z(j)| v. f) and the phase angle versus frequency (i.e., Z(j) v. f) 3 Lecture 19 Frequency Response of a Resistor Consider the frequency dependent impedance of the resistor, inductor and capacitor circuit elements Resistor (R): ZR = R 0° 4 Phase of ZR (°) Magnitude of ZR () So the magnitude and phase angle of the resistor impedance are constant, such that plotting them versus frequency yields R Lecture 19 Frequency 0° Frequency Frequency Response of an Inductor 5 Lecture 19 Phase of ZL (°) Magnitude of ZL () Inductor (L): ZL = L 90° The phase angle of the inductor impedance is a constant 90°, but the magnitude of the inductor impedance is directly proportional to the frequency. Plotting them vs. frequency yields (note that the inductor appears as a short at dc) Frequency 90° Frequency Frequency Response of a Capacitor 6 Lecture 19 Phase of ZC (°) Magnitude of ZC () Capacitor (C): ZC = 1/(C) –90° The phase angle of the capacitor impedance is –90°, but the magnitude of the inductor impedance is inversely proportional to the frequency. Plotting both vs. frequency yields (note that the capacitor acts as an open circuit at dc) -90° Frequency Frequency Transfer Function Recall that the transfer function, H(s), is Y ( s) Output H ( s) X( s ) Input The transfer function can be shown in a block diagram as X(j) ejt = X(s) est Y(j) ejt = Y(s) est H(j) = H(s) The transfer function can be separated into magnitude and phase angle information, H(j) = |H(j)| H(j) 7 Lecture 19 Common Transfer Functions Since the transfer function, H(j), is the ratio of some output variable to some input variable, H( j ) Y( j ) Output X( j ) Input We may define any number of transfer functions ratio of output voltage to input current, i.e., transimpedance, Z(jω) ratio of output current to input voltage, i.e., transadmittance, Y(jω) ratio of output voltage to input voltage, i.e., voltage gain, GV(jω) ratio of output current to input current, i.e., current gain, GI(jω) 8 Lecture 19 Poles and Zeros The transfer function is a ratio of polynomials N ( s ) K ( s z1 )( s z 2 ) ( s z m ) H( s ) D( s ) ( s p1 )( s p2 ) ( s pn ) The roots of the numerator, N(s), are called the zeros since they cause the transfer function H(s) to become zero, i.e., H(zi)=0 The roots of the denominator, D(s), are called the poles and they cause the transfer function H(s) to become infinity, i.e., H(pi)= 9 Lecture 19