Download Document

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Stray voltage wikipedia , lookup

Current source wikipedia , lookup

Electronic engineering wikipedia , lookup

Transistor wikipedia , lookup

Optical rectenna wikipedia , lookup

Shockley–Queisser limit wikipedia , lookup

Voltage optimisation wikipedia , lookup

Triode wikipedia , lookup

Alternating current wikipedia , lookup

Power electronics wikipedia , lookup

Mercury-arc valve wikipedia , lookup

Mains electricity wikipedia , lookup

Surge protector wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Buck converter wikipedia , lookup

Opto-isolator wikipedia , lookup

Rectifier wikipedia , lookup

Diode wikipedia , lookup

Transcript
electronics fundamentals
circuits, devices, and applications
THOMAS L. FLOYD
DAVID M. BUCHLA
chapter 16
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Semiconductors
Semiconductors are crystalline materials that are
characterized by specific energy bands for electrons.
Energy
Between the bands are gaps;
these gaps represent energies
Conduction band
that electrons cannot posses.
The last energy band is the
conduction band, where electrons
are mobile.
The next to the last band is the
valence band, which is the energy
level associated with electrons
involved in bonding.
Electronics Fundamentals 8th edition
Floyd/Buchla
Energy gap
Valence band
Energy gap
Second band
Energy gap
First band
Nucleus
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Electron and hole current
At room temperature, some electrons have enough
energy to jump into the conduction band.
After jumping the gap, these electrons are free to drift throughout
the material and form electron current when a voltage is applied.
Electronhole pair
Energy
For every electron
in the conduction
band, a hole is left
behind in the
valence band.
Electronics Fundamentals 8th edition
Floyd/Buchla
Conduction band
Energy gap
Heat
energy
Valence band
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Electron and hole current
The electrons in the conduction band and the holes in
the valence band are the charge carriers. In other words,
current in the conduction band is by electrons; current
in the valence band is by holes.
When an electron jumps to the conduction band, valence
electrons move from hole-to-hole in the valence band,
effectively creating “hole current” shown by gray arrows.
Si
Electronics Fundamentals 8th edition
Floyd/Buchla
Si
Free
electron
Si
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Impurities
By adding certain impurities to pure (intrinsic) silicon,
more holes or more electrons can be produced within
the crystal.
To increase the number of conduction
band electrons, pentavalent impurities
are added, forming an n-type
semiconductor. These are elements to
the right of Si on the Periodic Table.
To increase the number of holes, trivalent
impurities are added, forming a p-type
semiconductor. These are elements to the
left of Si on the Periodic Table.
Electronics Fundamentals 8th edition
Floyd/Buchla
III IV V
B C N
Al Si P
Ga Ge As
In Sn Sb
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
The pn junction diode
When a pn junction is formed, electrons in the n-material
diffuse across the junction and recombine with holes in
the p-material. This action continues until the voltage of
the barrier repels further diffusion. Further diffusion
across the barrier requires the application of a voltage.
The pn junction is basically a diode,
which is a device that allows current
in only one direction. A few typical
diodes are shown.
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Forward bias
When a pn junction is forward-biased, current is permitted.
The bias voltage pushes conduction-band electrons in the
n-region and holes in the p-region toward the junction
where they combine.
p-region n-region
The barrier potential in the depletion
region must be overcome in order
for the external source to cause
current. For a silicon diode, this is
about 0.7 V.
p
n
R
-
+
VBIAS
The forward-bias causes the depletion region to be narrow.
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Reverse bias
When a pn junction is reverse-biased, the bias voltage
moves conduction-band electrons and holes away from the
junction, so current is prevented.
p-region n-region
The diode effectively acts as an
insulator. A relatively few electrons
manage to diffuse across the
junction, creating only a tiny reverse
current.
p
n
R
-
+
VBIAS
The reverse-bias causes the depletion region to widen.
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Diode characteristics
The forward and reverse characteristics are shown on
a V-I characteristic curve.
In the forward bias region, current
increases dramatically after the
barrier potential (0.7 V for Si) is
reached. The voltage across the
diode remains approximately
equal to the barrier potential.
The reverse-biased diode
effectively acts as an insulator
until breakdown is reached.
IF
VBR (breakdown)
Forward
bias
VR
0.7 V
Reverse
bias
VF
Barrier
potential
IR
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Diode models
The characteristic curve for a diode can be approximated
by various models of diode behavior. The model you will
IF
use depends on your requirements.
The ideal model assumes the diode is
either an open or closed switch.
The practical model includes the VR
barrier voltage in the approximation.
Forward
bias
0.7 V
VF
Reverse
bias
The complete model includes the
forward resistance of the diode.
IR
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Half-wave Rectifier
Rectifiers are circuits that convert ac to dc. Special
diodes, called rectifier diodes, are designed to handle the
higher current requirements in these circuits.
The half-wave rectifier
converts ac to pulsating
dc by acting as a closed
switch during the
positive alteration.
The diode acts as an
open switch during the
negative alteration.
Electronics Fundamentals 8th edition
Floyd/Buchla
+
D
RL
D
- +
RL
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Full-wave Rectifier
The full-wave rectifier allows unidirectional current on
both alterations of the input. The center-tapped full-wave
rectifier uses two diodes and a center-tapped transformer.
The ac on each side of the center-tap is ½ of the total secondary
voltage. Only one diode will be biased on at a time.
D1
F
Vsec
2
Vsec
2
Electronics Fundamentals 8th edition
Floyd/Buchla
D2
RL
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Bridge Rectifier
The bridge rectifier is a type of full-wave circuit that uses
four diodes. The bridge rectifier does not require a
center-tapped transformer.
At any instant, two of the diodes are conducting and two are off.
F
D3
D2
Electronics Fundamentals 8th edition
Floyd/Buchla
D1
D4
RL
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Peak inverse voltage
Diodes must be able to withstand a reverse voltage when
they are reverse biased. This is called the peak inverse
voltage (PIV). The PIV depends on the type of rectifier
circuit and the maximum secondary voltage.
For example, in a full-wave circuit, if one diode is conducting
(assuming 0 V drop), the other diode has the secondary voltage
across it as you can see from applying KVL around the green path.
Notice that Vp(sec) = 2Vp(out) for
the full-wave circuit because
the output is referenced to the
center tap.
Electronics Fundamentals 8th edition
Floyd/Buchla
0V
Vsec
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Peak inverse voltage
For the bridge rectifier, KVL can be applied to a loop that
includes two of the diodes. Assume the top diode is
conducting (ideally, 0 V) and the lower diode is off. The
secondary voltage will appear across the non-conducting
diode in the loop.
Notice that Vp(sec) = Vp(out) for the bridge because the output is
across the entire secondary.
0V
Vsec
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Power supplies
By adding a filter and regulator to the basic rectifier, a
basic power supply is formed.
Typically, a large electrolytic capacitor is used as a filter before the
regulator, with a smaller one following the regulator to complete
filtering action.
IC regulator
F
D3
D1
7805
D2
Electronics Fundamentals 8th edition
Floyd/Buchla
D4
C1
1000 mF
C2
1 mF
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Special-purpose diodes
Special purpose diodes include
Zener diodes – used for establishing a reference voltage
Varactor diodes – used as variable capacitors
Light-emitting diodes – used in displays
Photodiodes – used as light sensors
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Troubleshooting power supplies
Begin troubleshooting by analyzing the symptoms and how
it failed. Try to focus on the most likely causes of failure.
A power supply has no output, but was working until a
newly manufactured PC board was connected to it. (a) Analyze
possible failures. (b) Form a plan for troubleshooting.
IC regulator
F
D3
D1
7805
D2
Electronics Fundamentals 8th edition
Floyd/Buchla
D4
C1
1000 mF
C2
1 mF
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Troubleshooting power supplies
The supply had been working, so the problem is not
likely to be an incorrect part or wiring problem. The failure was
linked to the fact that a new PC board was connected to it,
which points to a possible overloading problem. If the load was
too much for the supply, it is likely a fuse would have blown, or
a part would likely have overheated, accounting for the lack of
output.
IC regulator
F
D3
D1
7805
D2
Electronics Fundamentals 8th edition
Floyd/Buchla
D4
C1
1000 mF
C2
1 mF
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Troubleshooting power supplies
Based on the analysis, a sample plan is as
follows. (It can be modified as circumstances warrant.)
1. Disconnect power and check the fuse. If it is bad, replace it.
Before reapplying power, remove the load, open the power supply
case, and look for evidence of overheating (such as discolored
parts or boards). If no evidence of overheating proceed.
2. Check the new pc board (the load) for a short or overloading of
the power supply that would cause the fuse to blow. Look for
evidence of overheating.
3. Verify operation of the supply with measurements (see next
slide).
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Summary
Troubleshooting power supplies
The analysis showed that a
likely cause of failure was due to an overload. For the
measurement step, it may be as simple as replacing the
fuse and confirming that the supply works. After
replacing the fuse:
Reapply power to the supply but with no load. If the output is
okay, put a resistive test load on the power supply and measure
the output to verify it is operational. If the output is correct, the
problem is probably with the new pc board. If not, you will need
to further refine the analysis and plan, looking for an internal
problem.
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Selected Key Terms
Majority carrier The most numerous charge carrier in a doped
semiconductor material (either free electrons
or holes.
Minority carrier The least numerous charge carrier in a doped
semiconductor material (either free electrons
or holes.
PN junction The boundary between n-type and p-type
semiconductive materials.
Diode An electronic device that permits current in
only one direction.
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Selected Key Terms
Barrier The inherent voltage across the depletion
potential region of a pn junction diode.
Forward bias The condition in which a diode conducts
current.
Reverse bias The condition in which a diode prevents
current.
Full-wave A circuit that converts an alternating sinerectifier wave into a pulsating dc consisting of both
halves of a sine wave for each input cycle.
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Selected Key Terms
Bridge rectifier A type of full-wave rectifier consisting of
diodes arranged in a four corner configuration.
Zener diode A type of diode that operates in reverse
breakdown (called zener breakdown) to
provide a voltage reference.
Varactor A diode used as a voltage-variable capacitor.
Photodiode A diode whose reverse resistance changes
with incident light.
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Quiz
1. An energy level in a semiconductor crystal in which
electrons are mobile is called the
a. barrier potential.
b. energy band.
c. conduction band.
d. valence band.
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Quiz
2. A intrinsic silicon crystal is
a. a poor conductor of electricity.
b. an n-type of material.
c. a p-type of material.
d. an excellent conductor of electricity.
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Quiz
3. A small portion of the Periodic Table is shown. The
elements highlighted in yellow are
a. majority carriers.
b. minority carriers.
c. trivalent elements.
d. pentavalent elements.
Electronics Fundamentals 8th edition
Floyd/Buchla
III IV V
B C N
Al Si P
Ga Ge As
In Sn Sb
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Quiz
4. At room temperature, free electrons in a p-material
a. are the majority carrier.
b. are the minority carrier.
c. are in the valence band.
d. do not exist.
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Quiz
5. The breakdown voltage for a silicon diode is reached
when
a. the forward bias is 0.7 V.
b. the forward current is greater than 1 A.
c. the reverse bias is 0.7 V.
d. none of the above.
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Quiz
6. The circuit shown is a
a. half-wave rectifier.
b. full-wave rectifier.
c. bridge rectifier.
d. zener regulator.
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Quiz
7. PIV stands for
a. Positive Ion Value.
b. Programmable Input Varactor.
c. Peak Inverse Voltage.
d. Primary Input Voltage.
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Quiz
8. A type of diode used a a voltage-variable capacitor is a
a. varactor.
b. zener.
c. rectifier.
d. LED.
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Quiz
9. If one of the four diodes in a bridge rectifier is open, the
output will
a. be zero.
b. have ½ as many pulses as normal.
c. have ¼ as many pulses as normal.
d. be unaffected.
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Quiz
10. When troubleshooting a power supply that has a
bridge rectifier, begin by
a. replacing the bridge rectifier.
b. replacing the transformer.
c. making measurements.
d. analyzing the symptoms and how it failed.
Electronics Fundamentals 8th edition
Floyd/Buchla
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.
Chapter 16
Quiz
Answers:
Electronics Fundamentals 8th edition
Floyd/Buchla
1. c
6. b
2. a
7. c
3. c
8. a
4. b
9. b
5. d
10. d
© 2010 Pearson Education, Upper Saddle
River, NJ 07458. All Rights Reserved.