Download Amateur Radio Technician Class Element 2 Course Presentation

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Wireless power transfer wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Islanding wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Opto-isolator wikipedia , lookup

Spark-gap transmitter wikipedia , lookup

Wien bridge oscillator wikipedia , lookup

Mathematics of radio engineering wikipedia , lookup

Zobel network wikipedia , lookup

MIMO wikipedia , lookup

Heterodyne wikipedia , lookup

Regenerative circuit wikipedia , lookup

Transcript
Element 2 Technician Class
Question Pool
T7
Station equipment; common transmitter and
receiver problems, antenna measurements
and troubleshooting, basic repair and testing
[4 Exam Questions – 4 Groups]
Valid July 1, 2010
Through
June 30, 2014
T7A01
A.
B.
C.
D.
What is the function of a product detector?
Detect phase modulated signals
Demodulate FM signals
Detect CW and SSB signals
Combine speech and RF signals
2
T7A02
A.
B.
C.
D.
What type of receiver is shown in
Figure T6?
Direct conversion
Super-regenerative
Single-conversion superheterodyne
Dual-conversion superheterodyne
3
T7A03
What is the function of a mixer in a
superheterodyne receiver?
A. To reject signals outside of the desired
passband
B. To combine signals from several
stations together
C. To shift the incoming signal to an
intermediate frequency
D. To connect the receiver with an
auxiliary device, such as a TNC
4
T7A04
A.
B.
C.
D.
What circuit is pictured in Figure T7, if
block 1 is a frequency discriminator?
A double-conversion receiver
A regenerative receiver
A superheterodyne receiver
An FM receiver
Radio
Frequency
Amplifier
Wide
Filter
Mixer
Intermediate
Frequency
Amplifier
Oscillator
Limiter
Block 1
Figure T7
Audio
Amplifier
5
T7A05
A.
B.
C.
D.
What is the function of block 1 if figure T4 is
a simple CW transmitter?
Reactance modulator
Product detector
Low-pass filter
Oscillator
1
Figure T4
Antenna
Driver
Power
Amplifier
Telegraph
Key
6
T7A06
A.
B.
C.
D.
What device takes the output of a lowpowered 28 MHz SSB exciter and produces
a 222 MHz output signal?
High-pass filter
Low-pass filter
Transverter
Phase converter
7
T7A07
A.
B.
C.
D.
If figure T5 represents a transceiver in which block
1 is the transmitter portion and block 3 is the
receiver portion, what is the function of block 2?
A balanced modulator
A transmit-receive switch
A power amplifier
A high-pass filter
8
T7A08
A.
B.
C.
D.
Which of the following circuits combines a
speech signal and an RF carrier?
Beat frequency oscillator
Discriminator
Modulator
Noise blanker
9
T7A09
A.
B.
C.
D.
Which of the following devices is most
useful for VHF weak-signal
communication?
A quarter-wave vertical antenna
A multi-mode VHF transceiver
An omni-directional antenna
A mobile VHF FM transceiver
10
T7A10
A.
B.
C.
D.
What device increases the low-power
output from a handheld transceiver?
A voltage divider
An RF power amplifier
An impedance network
A voltage regulator
11
T7A11
A.
B.
C.
D.
Which of the following circuits
demodulates FM signals?
Limiter
Discriminator
Product detector
Phase inverter
12
T7A12
A.
B.
C.
D.
Which term describes the ability of a
receiver to discriminate between
multiple signals?
Tuning rate
Sensitivity
Selectivity
Noise floor
13
T7A13
Where is an RF preamplifier installed?
A. Between the antenna and receiver
B. At the output of the transmitter’s power
amplifier
C. Between a transmitter and antenna
tuner
D. At the receiver’s audio output
14
What can you do if you are told your
FM handheld or mobile
transceiver is
over deviating?
T7B01
A.
B.
C.
D.
Talk louder into the microphone
Let the transceiver cool off
Change to a higher power level
Talk farther away from the microphone
15
T7B02
What is meant by fundamental overload in
reference to a receiver?
A. Too much voltage from the power
supply
B. Too much current from the power
supply
C. Interference caused by very strong
signals
D. Interference caused by turning the
volume up too high
16
T7B03
A.
B.
C.
D.
Which of the following may be a cause of
radio frequency interference?
Fundamental overload
Harmonics
Spurious emissions
All of these choices are correct
17
T7B04
What is the most likely cause of
interference to a non-cordless telephone
from a nearby transmitter?
A. Harmonics from the transmitter
B. The telephone is inadvertently acting as
a radio receiver
C. Poor station grounding
D. Improper transmitter adjustment
18
T7B05
A.
B.
C.
D.
What is a logical first step when attempting
to cure a radio frequency interference
problem in a nearby telephone?
Install a low-pass filter at the transmitter
Install a high-pass filter at the transmitter
Install an RF filter at the telephone
Improve station grounding
19
T7B06
What should you do first if someone tells
you that your station’s transmissions are
interfering with their radio or TV reception?
A. Make sure that your station is functioning properly and
that it does not cause interference to your own
television
B. Immediately turn off your transmitter and contact the
nearest FCC office for assistance
C. Tell them that your license gives you the right to
transmit and nothing can be done to reduce the
interference
D. Continue operating normally because your equipment
cannot possibly cause any interference
20
T7B07
A.
B.
C.
D.
Which of the following may be useful
in correcting a radio frequency
interference problem?
Snap-on ferrite chokes
Low-pass and high-pass filters
band-reject and band-pass filters
All of these choices are correct
21
T7B08
What should you do if a "Part 15" device in
your neighbor’s home is causing harmful
interference to your amateur station?
A. Work with your neighbor to identify the
offending device
B. Politely inform your neighbor about the rules
that require him to stop using the device if it
causes interference
C. Check your station and make sure it meets the
standards of good amateur practice
D. All of these choices are correct
22
T7B09
What could be happening if another
operator reports a variable high-pitched
whine on the audio from your mobile transmitter?
A. Your microphone is picking up noise from
an open window
B. You have the volume on your receiver set
too high
C. You need to adjust your squelch control
D. Noise on the vehicle’s electrical system is
being transmitted along with your speech
audio
23
T7B10
What might be the problem if you receive a
report that your audio signal through the
repeater is distorted or unintelligible?
A. Your transmitter may be slightly off
frequency
B. Your batteries may be running low
C. You could be in a bad location
D. All of these choices are correct
24
T7B11
What is a symptom of RF feedback in a
transmitter or transceiver?
A. Excessive SWR at the antenna
connection
B. The transmitter will not stay on the
desired frequency
C. Reports of garbled, distorted, or
unintelligible transmissions
D. Frequent blowing of power supply fuses
25
T7B12
A.
B.
C.
D.
What does the acronym "BER" mean when
applied to digital communications systems?
Baud Enhancement Recovery
Baud Error Removal
Bit Error Rate
Bit Exponent Resource
26
T7C01
What is the primary purpose of a
dummy load?
A. To prevent the radiation of signals when
making tests
B. To prevent over-modulation of your
transmitter
C. To improve the radiation from your
antenna
D. To improve the signal to noise ratio of
your receiver
27
T7C02
A.
B.
C.
D.
Which of the following instruments can be
used to determine if an antenna is resonant
at the desired operating frequency?
A VTVM
An antenna analyzer
A “Q” meter
A frequency counter
28
What, in general terms, is standing wave
ratio (SWR)?
T7C03
A. A measure of how well a load is
matched to a transmission line
B. The ratio of high to low impedance in a
feedline
C. The transmitter efficiency ratio
D. An indication of the quality of your
station’s ground connection
29
T7C04
A.
B.
C.
D.
What reading on an SWR meter indicates a
perfect impedance match between the
antenna and the feedline?
2 to 1
1 to 3
1 to 1
10 to 1
30
T7C05
A.
B.
C.
D.
What is the approximate SWR value above which
the protection circuits in most solid-state
transmitters begin to reduce transmitter power?
2 to 1
1 to 2
6 to 1
10 to 1
31
T7C06
A.
B.
C.
D.
What does an SWR reading of 4:1 mean?
An antenna loss of 4 dB
A good impedance match
An antenna gain of 4
An impedance mismatch
32
T7C07
What happens to power lost in a feedline?
A. It increases the SWR
B. It comes back into your transmitter and
could cause damage
C. It is converted into heat
D. It can cause distortion of your signal
33
T7C08
A.
B.
C.
D.
What instrument other than an SWR meter
could you use to determine if a feedline
and antenna are properly matched?
Voltmeter
Ohmmeter
Iambic pentameter
Directional wattmeter
34
T7C09
A.
B.
C.
D.
Which of the following is the most common
cause for failure of coaxial cables?
Moisture contamination
Gamma rays
The velocity factor exceeds 1.0
Overloading
35
T7C10
Why should the outer jacket of coaxial
cable be resistant to ultraviolet light?
A. Ultraviolet resistant jackets prevent
harmonic radiation
B. Ultraviolet light can increase losses in
the cable’s jacket
C. Ultraviolet and RF signals can mix
together, causing interference
D. Ultraviolet light can damage the jacket
and allow water to enter the cable
36
T7C11
What is a disadvantage of "air core" coaxial
cable when compared to foam or solid
dielectric types?
A. It has more loss per foot
B. It cannot be used for VHF or UHF
antennas
C. It requires special techniques to
prevent water absorption
D. It cannot be used at below freezing
temperatures
37
T7D01
A.
B.
C.
D.
Which instrument would you use to
measure electric potential or
electromotive force?
An ammeter
A voltmeter
A wavemeter
An ohmmeter
38
T7D02
A.
B.
C.
D.
What is the correct way to connect a
voltmeter to a circuit?
In series with the circuit
In parallel with the circuit
In quadrature with the circuit
In phase with the circuit
39
T7D03
A.
B.
C.
D.
How is an ammeter usually connected
to a circuit?
In series with the circuit
In parallel with the circuit
In quadrature with the circuit
In phase with the circuit
40
T7D04
A.
B.
C.
D.
Which instrument is used to measure
electric current?
An ohmmeter
A wavemeter
A voltmeter
An ammeter
41
T7D05
A.
B.
C.
D.
What instrument is used to measure
resistance?
An oscilloscope
A spectrum analyzer
A noise bridge
An ohmmeter
42
T7D06
Which of the following might damage
a multimeter?
A. Measuring a voltage too small for the
chosen scale
B. Leaving the meter in the milliamps
position overnight
C. Attempting to measure voltage when
using the resistance setting
D. Not allowing it to warm up properly
43
T7D07
A.
B.
C.
D.
Which of the following measurements are
commonly made using a multimeter?
SWR and RF power
Signal strength and noise
Impedance and reactance
Voltage and resistance
44
T7D08
A.
B.
C.
D.
Which of the following types of solder is
best for radio and electronic use?
Acid-core solder
Silver solder
Rosin-core solder
Aluminum solder
45
T7D09
A.
B.
C.
D.
What is the characteristic appearance of a
"cold" solder joint?
Dark black spots
A bright or shiny surface
A grainy or dull surface
A greenish tint
46
T7D10
A.
B.
C.
D.
What is probably happening when an ohmmeter,
connected across a circuit, initially indicates a low
resistance and then shows increasing resistance with time?
The ohmmeter is defective
The circuit contains a large capacitor
The circuit contains a large inductor
The circuit is a relaxation oscillator
47
T7D11
Which of the following precautions should
be taken when measuring circuit resistance
with an ohmmeter?
A. Ensure that the applied voltages are
correct
B. Ensure that the circuit is not powered
C. Ensure that the circuit is grounded
D. Ensure that the circuit is operating at
the correct frequency
48