Download Welcome to Clear Talk!

Welcome to Clear Talk!
This guide will assist you in setting up your new VoIP device
ClearTalk ATA
-1-
www.clearnetworks.com.au - 1300 855 215
ATA Overview
The Phone Adapter’s LEDs are located on the front panel.
Phone 1 LED. The Phone 1 LED is solidly lit when a telephone or fax machine has a registered connection to
ClearTalk through the Phone 1 port.
(The connection is registered if your Internet phone service account is active.)
It flashes when the phone is being used or an incoming call has been detected.
Phone 2 LED. The Phone 2 LED is solidly lit when a telephone or fax machine has a registered connection to Clear
Talk through the Phone 2 port. It flashes when the phone is being used or an incoming call has been detected.
(Note the Phone2 port can only be used with a second Clear Talk account/number)
Ethernet LED. The Ethernet LED lights up when the Phone Adapter is connected to your network through the
Ethernet port.
It flashes when there is data being sent or received.
Power LED. The Power LED lights up when the Phone Adapter is powered on and ready. It flashes when the
Phone Adapter is booting up, undergoing a self-test, or performing a firmware upgrade.
The LED lights up red when the Phone Adapter has failed its self-test or is malfunctioning.
Contact Clear Networks Customer Care for further assistance (1300 855 215).
Connecting Voip to your existing Clear Networks Satellite.
Figure 1-1 Voip Connection Overview
1. Using a telephone cable, connect your telephone to the Phone 1 port of the Phone Adapter.
NB. If you have a second ClearTalk line on your account, then connect
another telephone or a fax machine to the Phone 2 port of the Phone
-2-
www.clearnetworks.com.au - 1300 855 215
Adapter.
2. Connect the included Ethernet network cable to the Ethernet port of the Phone Adapter.
Connect the other end to the one of the Ethernet ports on your router or switch.
3. Connect the included power adapter to the POWER port on the back panel of the Phone Adapter. Connect the
other end to a standard electrical outlet.
4. The Power, Ethernet, and Phone LEDs will be solidly lit when the Phone Adapter is ready for use.
(The Phone2 LED will only light if you have a second account)
The installation of the Phone Adapter is complete. Now you can pick up your phone and make calls.
Using your Own Router
A note to customers using their own router, you will need to forward ports from your router to your PAP2 prior
to be able to receive incoming calls, the ports required are 5060, 5061, and 69.
You will also need to set the IP on the PAP2 to suit your network.
You can obtain further information on forwarding ports in your routers documentation.
Please note Clear Networks cannot provide assistance with third party devices, these instructions are provided
“as is” and are a guide only.
Manually Setting Your PAP2’s IP address
If you have a Router that was not supplied by Clear Networks, you will be required to forward ports to the PAP2,
to do this you will also need to setup a Static IP address on the PAP2 to suit your network.
1. Find an IP that is free within your network
2. Find out the gateway address of your network (this is usually the routers IP)
-3-
www.clearnetworks.com.au - 1300 855 215
3. Find out the Subnet mask of your network (usually 255.255.255.0)
4. Using the phone connected to your ATA input the new IP address
- Press “****” (Star Four Times) you will hear “Configuration menu”
- Key in “101#” you will hear a prompt asking if you would like to enable DHCP
- Key in “0#” this will disable DHCP and take you back to the main menu
- Now key in “111#” you will be asked for the IP address
- Key in the IP address, substituting Stars “*” for the decimal point and Hash “#” when you are finished
- Press 1 to save the IP address
-Hang up the phone
5. Using the phone connected to your ATA input the new Subnet mask
(the subnet mask is set to 255.255.255.0 by default, you can skip this step if yours is the same)
- Press “****” (Star Four Times) you will hear “Configuration menu”
- Key in “121#” you will hear a prompt asking if you would like to enable DHCP
- Key in the Subnet, substituting Stars “*” for the decimal point and Hash “#” when you are finished
- Press 1 to save the Subnet Mask
- Hang up the phone
6. Using the phone connected to your ATA input the new Gateway Address
- Press “****” (Star Four Times) you will hear “Configuration menu”
- Now key in “131#” you will be asked for the IP address
- Key in the IP address, substituting Stars “*” for the decimal point and Hash “#” when you are finished
- Press 1 to save the IP address of the Gateway
- Hang up the phone
Your ATA now has a static IP address, restart your router according to its instructions then unplug the ATA from
power for 2 minutes, when you plug the phone back in your port forwarding will be complete.
Your ClearTalk Network Number is: ______________________________________
-4-
www.clearnetworks.com.au - 1300 855 215