Download Lms43LED-CG - LED Microsensor NT

Mid-Infrared (MIR) Light-Emitting Diode
Series with a glass cover
4,1 - 4.3 μm
Lms43LED-CG
Device parameters
Symbol
Value
Units
Storage temperature
Tstg
-25..+50
°C
Operating temperature
Topr
-25..+50
°C
Lead soldering temperature
(time < 3 seconds, 3 mm from case)
Tsol
+180
°C
LED parameters
Conditions
Symbol
Peak emission wavelength
T = 25 °C, I = 150 mA qCW
FWHM of the emission band
Output optical power
Value
Units
λp
4.1 - 4.3
mm
T = 25 °C, I = 150 mA qCW
FWHM
600 - 1200
nm
quasi-CW mode
I = 200 mA, duty cycle 50%
Pqcw
min 25
mW
pulse mode
I = 1 А , f = 2 kHz, duty cycle 0.1%
Ppulse
min 500
mW
T = 25 °C; I = 200 mA qCW
V
0.2 - 0.8
V
Forward Voltage
Maximum allowable operation current
Mode
Frequency
Duty cycle
Pulse duration
Maximum current
quasi- CW
0.5 kHz
50%
1000 ms
250 mA
pulse
2 kHz
0.1%
0.5 ms
1A
Light-Emitting Diodes Lms43LED series are fabricated from narrow band-gap InAsSbP/InAs-based heterostructures lattice
matched to InAs substrate.
Intensity, a.u.
Spectra at 200 mA (qCW, duty cycle 50%, T=25 °C)
90
80
70
60
50
40
30
20
10
0
2500
CO2 absorption
3000
3500
4000
4500
5000
5500
Wavelength, nm
LED Typical Power Characteristic (qCW, T=25 °C)
LED Typical Current-Voltage Characteristic (qCW, T=25 °C)
250
70
200
Current, mA
Optical Power, mW
80
60
50
40
30
150
100
50
20
10
0
0
0
50
100
Current, mA
Rev.230415
150
200
-400
-200
-50
0
200
400
Voltage, mV
The design and specifcation of the product can be changed by LED Microsensor NT LLC. without notice
HEAD OFFICE: LED Microsensor NT, LLC RnD CENTRE: Microsensor Technology, LLC, 194223, postbox 100, St. Petersburg, Russia
www.lmsnt.com, [email protected]
Mid-Infrared (MIR) Light-Emitting Diode
4,1 - 4.3 μm
Series with a glass cover
Lms43LED-CG
Packages
Model
TO-18 with a glass cover
Lms MIR LED-CG
To drive the LED we recommend using:
• LED drivers and evaluation boards
designed by LED Microsensor NT
• LED basic circuit connection
Pulse
Generator
LED
1 Ohm
We recommend to use Quasi Continuous Wave (qCW) mode with duty cycle 50% or 25% to obtain maximum average optical power and short Pulse
modes to obtain maximum peak power. Hard CW (continius wave) mode is NOT recommended.
31-1000 µs 31-1000 µs
f=0.5-16 kHz
0-250 mA
Drive current
Drive current
0.6-20 µs
62-2000 µs
f=0.5-16 kHz
0-1 A
Time
Time
IMPORTANT CAUTIONS:
●
●
●
●
●
check your connection circuit before turning on the LED;
mind the LED polarity: LED anode is marked with a RED dot;
do not connect the LED to the multimeter;
do not touch the glass covering and do not apply any force to it;
observe the allowable operating temperature range, exceeding this eange may cause irreparable damage of the glass cover
Rev.230415
The design and specifcation of the product can be changed by LED Microsensor NT LLC. without notice
HEAD OFFICE: LED Microsensor NT, LLC RnD CENTRE: Microsensor Technology, LLC, 194223, postbox 100, St. Petersburg, Russia
www.lmsnt.com, [email protected]
Mid-Infrared (MIR) Light-Emitting Diode
4,1 - 4.3 μm
Series with a glass cover
Lms43LED-CG
Technical Drawing
Lms MIR LED-CG
Related Products
● Photodiodes (Lms43PD-XX series) - spectrally matched detectors of mid-infrared radiation
● D-41/D-51 LED drivers - devices for LED driving with adjustable parameters
● mD-1p/mD-1c minidrivers - devices for LED driving with fixed parameters
Rev.230415
The design and specifcation of the product can be changed by LED Microsensor NT LLC. without notice
HEAD OFFICE: LED Microsensor NT, LLC RnD CENTRE: Microsensor Technology, LLC, 194223, postbox 100, St. Petersburg, Russia
www.lmsnt.com, [email protected]