Download Linear Series - Tokistar Lighting

T O K I S TA R L I G H T I N G
INSTRUCTION MANUAL
Linear Extrusion Manual - TXRW/TXRA/TDR Series
Single-Circuit Operation
General Description
Tokistar’s Linear Extrusions are provided with 8VDC LEDs. The LEDs for the TXRA and TDR Series
are available at 0.1 watt, 0.2 watt and 0.4 watt. The TXRW Series is provided with 0.24 watt LEDs. Each
fixture is labeled with its appropriate load.
TDR Series
TXRW Series
TXRA Series
Tokistar LEDs have polarity
The notch on TokiLeds
indicates the (+) side.
Push the LED
straight down
LED
Contact
Resistor
_
Notch (+)
Socket contact
+
The resistor on P4 LEDs
indicates the (-) side.
TDR & TXRA Series
TXRW Series
Wire Marked (+) side
PRECAUTIONS
1. Read all instructions completely before beginning installation.
2. Turn off electricity before beginning installation.
3. All wiring is to be performed by a qualified electrician.
4. Installation must comply with the National Electrical Code, and all applicable codes.
5. Turn main supply to the LED Driver on only after all connections have been made and tested.
6. Use only LED Drivers provided by Tokistar with the system.
TOKISTAR® LIGHTING
1015 E. Discovery Lane
Anaheim, CA 92801
TEL: 714 772 7005 FAX: 714 772 7014
email: [email protected] Website: www.tokistar.com
TXRW/TXRA/TDR Series Instructions Page 2
Secondary Circuit Wiring
Secondary Circuit Limitation
Circuits Must Not Exceed
5 Amps (40 Watts @ 8VDC)
LED Driver
Maximum Fixture Length
To minimize voltage drop and keep conductors safely within their rating, do not exceed the maximum distances
shown for independent run lengths with a single feed to the power supply. The maximum length for each TXR &
TDR extrusion is 96-1/2" (2.5 M).
TDR & TXRA Series
Spacing
2" (50 mm)
3" (75 mm)
4" (100 mm)
6" (150 mm)
12" (300 mm)
LEDs / 8 VDC
0.1 Watt
0.2 Watt
40' (12 M)
50' (15 M)
60' (18 M)
75' (22.5 M)
100' (30 M)
30' (9 M)
36' (10.8 M)
40' (12 M)
50' (15 M)
80' (25 M)
TXRW Series
P4 LEDs / 8 VDC
Spacing
0.24 Watt
0.4 Watt
16' (5 M)
25' (7.5 M)
30' (9 M)
36' (10.8 M)
60' (18 M)
Recommended Lead Wire Size
The distance from the LED Driver to the fixture and the load of the
fixture will determine the proper size of secondary wire. The chart
on the right indicates recommended wire size based upon the driver
being loaded to its full capacity of 5 Amps/40 Watts.
1" (25 mm)
2" (50 mm)
3" (75 mm)
4" (100 mm)
Secondary Lead Wires
Wire Size
Wire Length
#16 AWG
12' (3.6 M)
#14 AWG
20' (6.1 M)
#12 AWG
30' (9.1 M)
#10 AWG
45' (13.7 M)
Secondary Lead Wire
LED Driver
Cutting Extrusions
13'10" (4.15 M)
27' 8" (8.3 M)
36' (11 M)
40' (12 M)
If it is necessary to trim an extrusion, be sure to properly insulate conductors.
TXRW/TXRA/TDR Series Instructions Page 3
Mounting Fixtures
Fixtures must be securely mounted in place. Never position the fixture where LEDs may be in direct contact with
any surface or object. Construction adhesive, adhesive tape or screws may be used to mount fixtures. When using
construction adhesive or adhesive tape, the fixtures can be attached as one complete assembly.
Adhesive Tape Mounting
(Part #s: WFL-20 & WFL-108)
Adhesive tape works best on a smooth clean surface.
First attach the adhesive tape to the surface, then
remove the protective backing and press the Linear
fixture in place.
LED Driver Installation
LDR8-40
This 40 Watt UL Recognized Class 2 LED Driver
converts an AC input into an 8 VDC output. Refer to
the manual provided with the LED Driver for detailed
installation instructions.
LDR8-40
Tokistar Linear Extrusions are
ETL Listed when operated
from our LED Drivers.
PRECAUTIONS
Construction
Adhesive
Adhesive
Tape
Screws
LDR8-80
This dual output Class 2 LED Driver has two independent
40 Watt outputs. Refer to the manual provided with the
LED Driver for detailed installation instructions.
Fixture
Output 1
Fixture
Output 2
Fixture
LDR8-80
Part#
LDR8-40
LDR8-80
Input Volts
100~240
100~240
Output Volts
8 VDC
8 VDC
Output Ratings
1 @ 5 Amps
2 @ 5 Amps
Fixtures must be securely mounted in place. Never position the fixture where lamps make direct contact
with any surface or object.
TXRW/TXRA/TDR Series Instructions
Page 4
LED Dimmer Instructions (Optional)
LC Dimming System
Wall Dimmer - Part #: LC-DMR
Power to the remote wall dimmer is provided from the LED
Driver powering the first Dimmer Pack. A 50 foot CAT5
cable is provided.
LC-DMR
Dimmer Pack - Part #: LC-1CH-DP
Each dimmer pack receives an 8 VDC output from an
LDR8-40 LED Driver. The LDR8-80 LED Driver has
2 each 8 VDC outputs, and a dimmer pack is required for
each output. A CAT5 cable is provided with each unit.
Up to 25 dimmer packs may be connected in series if the
total length of all CAT5 cable does not exceed 165 feet
from the wall dimmer to the last dimmer pack.
Fixture
Fixture
0-8VDC
0-8VDC
Signal Out
Signal Out
Dimmer Pack
8VDC
Dimmer Pack
8VDC
LED Driver
LED Driver
For further information, refer to the instruction manual
provided with the LC-1CH-DP.
LC-1CH-MULTI Dimming System
Tokistar’s LC-1CH-MULTI Dimmer Pack is compatible
with industry-standard dimmers working on DMX or
0/1-10 VDC protocol.
DMX Wiring Diagram
DMX Console
Fixture
Dimmer Pack - Part #: LC-1CH-MULTI
0-8 VDC
DMX Mode - Each unit is independently addressable. Up to
36 dimmer packs may be connected in series. For applications
exceeding 36 dimmer packs, an additional feed from the DMX
dimmer is required. The additional feed(s) can be sent directly
from the dimmer, or you may use DMX Splitters. Consult factory
on details of DMX Splitters.
8 VDC
0-8 VDC
Dimmer Pack
Each dimmer pack receives an 8 VDC output from an LDR8-40
LED Driver. The LDR8-80 LED Driver has 2 each 8 VDC
outputs, and a dimmer pack is required for each output.
Dimmer Pack
LED Driver
LED Driver
8 VDC
DMX Out
DMX In
DMX Out
Analog Dimmer
0/1-10 VDC Wiring Diagram
Analog Modes - For operation from devices using 0/1-10VDC
protocol, up to 10 dimmer packs may be connected in series. For
applications exceeding 10 dimmer packs, an additional feed from
the analog dimming device is required.
Manual Mode - You may select a light intensity the fixtures will
operate at. In this case, no external dimming device is required.
Fixture
Fixture
Fixture
Analog Out
0-8 VDC
Analog Out
0-8 VDC
Dimmer Pack
Dimmer Pack
For further information, refer to the instruction manual
provided with the LC-1CH-MULTI.
8 VDC
PRECAUTION
8 VDC
LED Driver
LED Driver
All dimming components are rated for dry location only. They must be installed within an
enclosure suitable for the environment.
TOKISTAR® LIGHTING
1015 E. Discovery Lane
Anaheim, CA 92801
TEL: 714 772 7005 FAX: 714 772 7014
email: [email protected] Website: www.tokistar.com
Version 1.0