Download TOKISTAR LIGHTING INSTRUCTION MANUAL Cable Lighting - -

T O K I S TA R L I G H T I N G
INSTRUCTION MANUAL
-
Fixture Type
Cable Lighting
-
General Description
Tokistar’s Cable Lighting Series is low-voltage lighting system using 0.2 Watt LEDs operating at 8 VDC and
two types of incandescent lamps operating at 12 VAC. Each Cable Light fixture is labeled with wattage and
operating voltage.
MC Series
RC Series
CR Series
CT Series
MCC - 50 - 2000K
LED
Conductor
Socket
Incandescent
lamp
Conductor
Socket
Series
Socket Spacing
Light Source
Code
Code
Inches
Code
Watts/Volts
MCC
MCCD
MCW
MCWD
RC
RCD
CRO
CRL
CRLD
CTO
CTL
CTLD
30
50
80
100
150
1.2” (30 mm)
2.0” (50 mm)
3.0” (80 mm)
4.0” (100 mm)
6.0” (150 mm)
2000K
2500K
3000K
5000K
AM
BL
GR
RD
201
202
0.2 W / 8 VDC
0.2 W / 8 VDC
0.2 W / 8 VDC
0.2 W / 8 VDC
0.2 W / 8 VDC
0.2 W / 8 VDC
0.2 W / 8 VDC
0.2 W / 8 VDC
0.48 W / 12 VAC
0.9 W / 12 VAC
PRECAUTIONS
1. Read all instructions completely before beginning installation.
2. Turn off electricity before beginning installation.
3. All wiring is to be performed by a qualified electrician.
4. Installation must comply with the National Electrical Code, and all applicable codes.
5. Turn main supply to the LED Driver or transformer on only after all connections have been made and tested.
6. Use only LED Drivers or transformers provided by Tokistar with the system.
7. Certain adhesives produce a bi-product of corrosive gas during their curing process, and should not be used in conjunction with our LED Systems where the gas cannot be vented. Consult with the Sealant company for such applications.
TOKISTAR® LIGHTING
1015 E. Discovery Lane
Anaheim, CA 92801
TEL: 714 772 7005 FAX: 714 772 7014
email: [email protected] Website: www.tokistar.com
Cable Light Instructions
Page 2
Mounting Fixtures
Fixtures must be securely mounted in place. Never position the fixture where lamps may be in direct contact with any
surface or object. Construction adhesive, adhesive tape or screws may be used to mount fixtures. When using screws,
make sure the screw is located between lamp sockets.
When using construction adhesive or adhesive tape,
the channel can be attached as one complete assembly.
Adhesive Tape Mounting
(Part #s: WF-CL20 & WF-CL50)
Construction
Adhesive
Adhesive
Tape
Adhesive tape works best on a smooth clean surface. First attach the
adhesive tape to the surface, then remove the protective backing and
press the Cable Lighting fixture in place.
Mounting with Screws
3) Snap in lens
When using screws, gently pry the base and cover apart and remove
the Cable Lighting fixture. Attach the base, making sure the screws
are located between sockets, then snap the fixture back in place and
reattach the cover.
2) Snap in fixture
1) Mount Base
Replacing Lamps
Fingertip pressure to the bulb or LED releases it from the
socket for easy and quick relamping.
Mounting Clamps
(Part #s: CTO-CP & RC-CP)
Mounting clamps are available for CTO and RC Series.
Recommended spacing is every 12”.
RC-CP width
.90"
(23 mm)
CTO-CP width
.60"
(15 mm)
CTO-CP
for CTO Series
.79"
(20 mm)
Recess width
RC-CP
for RC Series
1.10"
(28 mm)
Recess width
Cable Light Instructions
Page 3
LED Systems
Secondary Circuit Wiring
Secondary Circuit Limitation
Circuits Must Not Exceed
5 Amps (40 Watts @ 8 VDC)
LED Driver
LED Driver Installation
LDR8-80
LDR8-40
This dual output Class 2 LED Driver has two independent
40 Watt outputs. Refer to the manual provided with the
LED Driver for detailed installation instructions.
This 40 Watt UL Recognized Class 2 LED Driver
converts an AC input into an 8 VDC output. Refer to
the manual provided with the LED Driver for detailed
installation instructions.
Fixture
LDR8-40
Fixture
Output 1
LDR8-80
Output 2
Fixture
Part#
Input Volts
Output Volts
Output Ratings
LED Capacity
LDR8-40
LDR8-80
100~240
100~240
8 VDC
8 VDC
1 @ 5 Amps
2 @ 5 Amps
200
400
Incandescent Systems
Secondary Circuit Wiring
Secondary Circuit Limitation
Circuits Must Not Exceed
5 Amps (60 Watts @ 12 VAC)
Class 2 Transformers
Part Number
Outputs
0.48 Watt
0.90 Watt
C2-60-12V
C2-120-12V
C2-180-12V
C2-240-12V
1 @ 60 Watt / 12VAC
2 @ 60 Watt / 12VAC
3 @ 60 Watt / 12VAC
4 @ 60 Watt / 12VAC
125
250
375
500
66
132
198
264
Transformer
Maximum Run Lengths
LEDs and Incandescent Lamps
To minimize voltage drop and keep conductors
safely within their rating, do not exceed the
maximum lengths shown in the chart to the
right for each independent length of Cable Light.
Spacing
0.2 Watt LED
1.2” (30 mm)
2.0” (50 mm)
3.0” (80 mm)
4.0” (100 mm)
6.0” (150 mm)
20’ (6.0 M)
33’ (10.0 M)
50’ (15.2 M)
60’ (18.3 M)
70’ (21.3 M)
Recommended Lead Wire Size
The distance from the LED Driver or transformer to the fixture,
and the load of the fixture, will determine the proper size of
secondary wire. The chart on the right indicates recommended
wire size based upon the driver/transformer being loaded to its
full capacity of 5 Amps.
Secondary Lead Wire
LED Driver
or Transformer
Incandescent Lamp Capacity
0.48 Watt CL-201 0.9 Watt CL-202
12’ (3.6 M)
20’ (6.0 M)
24’ (7.3 M)
30’ (9.1 M)
36’ (11.0 M)
Secondary Lead Wires
Wire Size
Wire Length
#16 AWG
12’ (3.6 M)
#14 AWG
20’ (6.1 M)
#12 AWG
30’ (9.1 M)
#10 AWG
45’ (13.7 M)
6’ (3.0 M)
11 (4.5 M)
16 (5.8 M)
21’ (6.4 M)
26’ (7.9 M)
Cable Light Instructions
Page 4
LED Dimmer Instructions (Optional)
LC Dimming System
Wall Dimmer - Part #: LC-DMR
Power to the remote wall dimmer is provided from the LED
Driver powering the first Dimmer Pack. A 50 foot CAT5
cable is provided.
LC- DMR
Fixture
Fixture
0-8 VDC
Dimmer Pack - Part #: LC-1CH-DP
0-8 VDC
Signal Out
Each dimmer pack receives an 8 VDC output from an LDR8-40
LED Driver. The LDR8-80 LED Driver has 2 each 8 VDC outputs,
and a dimmer pack is required for each output. A CAT5 cable is
provided with each unit. Up to 25 dimmer packs may be connected
in series if the total length of all CAT5 cable does not exceed 165 feet
from wall dimmer to last dimmer pack.
Dimmer Pack
8 VDC
Signal Out
Dimmer Pack
8 VDC
LED Driver
LED Driver
For further information, refer to the instruction manual provided
with the LC-1CH-DP.
LC-1CH-MULTI Dimming System
Tokistar’s LC-1CH-MULTI Dimmer Pack is compatible
with industry-standard dimmers working on DMX or
0/1-10 VDC protocol.
DMX Wiring Diagram
DMX Console
Fixture
Dimmer Pack - Part #: LC-1CH-MULTI
Each dimmer pack receives an 8 VDC output from an LDR8-40
LED Driver. The LDR8-80 LED Driver has 2 each 8 VDC
outputs, and a dimmer pack is required for each output.
DMX Mode - Each unit is independently addressable. Up to
36 dimmer packs may be connected in series. For applications
exceeding 36 dimmer packs, an additional feed from the DMX
dimmer is required. The additional feed(s) can be sent directly
from the dimmer, or you may use DMX Splitters.
Analog Modes - For operation from devices using 0/1-10VDC
protocol, up to 10 dimmer packs may be connected in series. For
applications exceeding 10 dimmer packs, an additional feed from
the analog dimming device is required.
Manual Mode - You may select a light intensity the fixtures will
operate at. In this case, no external dimming device is required.
For further information, refer to the instruction manuals
provided with the units.
Fixture
0-8 VDC
0-8 VDC
Dimmer Pack
Dimmer Pack
LED Driver
8 VDC
LED Driver
8 VDC
DMX Data
DMX Data
DMX Data
Analog Dimmer
0/1-10 VDC Wiring Diagram
Fixture
Fixture
Analog Out
Analog Out
0-8 VDC
0-8 VDC
Dimmer Pack
Dimmer Pack
8 VDC
LED Driver
8 VDC
LED Driver
PRECAUTION
All dimming components are rated for dry location only. They must be installed within an
enclosure suitable for the environment.
TOKISTAR® LIGHTING
1015 E. Discovery Lane
Anaheim, CA 92801
TEL: 714 772 7005 FAX: 714 772 7014
email: [email protected] Website: www.tokistar.com
Version 1.0