Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
ECM-S930C SERVICE MANUAL Ver 1.0 2001. 03 US Model Canadian Model E Model SPECIFICATIONS General Type Microphone cord Dimensions Mass Supplied accessories Stereo (employing the X-Y stereo system), electret condenser microphone 2.2 mm dia. two core-shielded, OFC (Oxygen-free copper) cord with the gold-plated L-shaped stereo miniplug Length: Approx. 30 cm (11 7/8 inches) Approx. 55 × 34 × 40 mm (W × H × D) (2 1/4 × 1 3/8 × 1 5/8 inches) (without the projecting parts) Approx. 40 g (1 lb. 4 oz.) including battery and cord Carrying case (1) Performance Frequency response Directivity 100 – 15,000 Hz Unidirectional × 2 (Directive angle: 90° or 120°) (switchable) Output impedance 2.2 kilohm ±30 % Sensitivity Open circuit output level *1 : –43 ±4 dB (7 mV) Difference between L and R channel sensitivity: Less than 3 dB Power requirements Lithium battery CR2025 Continuous lasting hours: Approx. 350 hours Plug-in power Maximum input sound pressure level *2 More than 110 dBSPL Dynamic range More than 84 dB Operating temperature range 0°C to 40°C (32°F to 104°F) *1 *2 0 dB=1 V/Pa, 1,000 Hz (1 Pa=10 µbar=94 dBSPL) 1 % wave distortion is present at 1,000 Hz (0 dBSPL=2 × 10-5 Pa) Design and specifications are subject to change without notice. Notes on Chip Component Replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. ELECTRET CONDENSER MICROPHONE 9-927-989-11 Sony Corporation 2001C0400-1 © 2001. 3 Audio Entertainment Group General Engineering Dept. 1 ECM-S930C SECTION 1 GENERAL A This section is extracted from instruction manual. Installing the battery (See fig. A) 1 Open the battery compartment lid. 2 Place the CR2025 battery (not supplied) with the + side facing upward. Be sure to place the battery with polarity positioned correctly. 1 Battery life The Sony CR2025 lithium battery (not supplied) gives continuous operation on the microphone for about 350 hours. When you turn the power on, the battery check indicator lights momentarily. When the battery becomes weak, the indicator lights dimly or does not light at all. In this case, replace the battery with a new one. (Sony CR2025 lithium battery (not supplied)). To avoid battery wear or leakage, be sure to turn the power off after using the microphone. 2 Lithium battery CR2025 (not supplied) Pile au lithium CR2025 (non fournie) Pila de litio CR2025 (no suministrada) + side pôle + lado + – side pôle – lado – When the battery compartment lid comes off 1 Hold down part A with a thumb so that it does not slide. 2 Insert one of the parts of A into the projecting part B of the battery compartment and then insert the other part while pressing toward the inside. Removing the battery (See fig. B) When to replace the battery When the power is turned on, the battery check indicator lights momentarily. When the battery become weak, the indicator remains dimly lit or does not light at all. In this case, replace the battery with Sony CR2025 lithium battery. Use of another battery may present a risk of fire or explosion. Under normal conditions of use, the battery will last approximately 350 hours. Notes on lithium battery • Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor. • Wipe the battery with a dry cloth to assure good contact. • Be sure to observe the correct polarity when installing the battery. • Do not hold the battery with metallic tweezers. Doing so can cause a short-circuit. A WARNING Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire. B Parts Identification and Uses (See fig. D) 1 Directive angle switch Set the switch according to the sound source. 90˚: Use to pick up a relatively narrower sound source (instrumental solo, conversation, etc.), to provide a clear stereo sound image focused on target source. 120˚: Use to pick up a relatively wider sound source (orchestra, chorus, stage play, etc.), to provide a natural stereo sound image with full reality. B 1 2 The above are guidelines for selecting an appropriate angle. Although following these guidelines is encouraged, you can freely select either angle according to your own preference. Note If you switch the angle during recording, noise may occure. 2 Gold-plated triple-pole stereo miniplug Connect to the MIC jack of your recording equipment (video camera, etc.) 3 Battery compartment lid 4 Power switch ON: Select when the microphone works with the battery. OFF: Select when the microphone works with plug-in power or when you turn it off. D 1 3 5 Battery check indicator When the power is turned on, this indicator lights momentarily. When the battery becomes weak, the indicator remains dimly lit or does not light at all. In this case, replace the battery with a new one. 2 4 5 2 When you use a Sony video camera with plug-in power system, set the power switch to OFF. ECM-S930C SECTION 2 DISASSEMBLY Note : Follow the disassembly procedure in the numerical order given. 2-1. CASE, UPPER 2-2. AMP BOARD Note : When installing, fit the selection knob and awitch (SW1) (center position) Note : When installing, fit the power knob and awitch (SW2) 4 case, upper grille knob, selection 3 claw 2 1 grille 3 Removal the solder. 2 2 lid, battery case knob, power 4 AMP board 1 B 1.7 2-3. HOLDER ASSY, SHOE 1 P 2.6x4 2 case, lower 3 holder assy, shoe 3 ECM-S930C SECTION 3 DIAGRAMS 3-1. PRINTED WIRING BOARD 2 1 3 4 5 6 7 AMP BOARD (COMPONENT SIDE) A SW1 (DIRECTIVE ANGLE) 120˚ 90˚ R2 MICROPHONE CAPSULE(R CH) MICROPHONE CAPSULE(L CH) C101 R102 C1 R1 R103 S S RE D GR Y R201 T C102 C103 C203 WH T MIC101 D RE C202 MIC201 C201 B R203 Q101 R202 Q201 WH Y GR R101 C4 C2 C BLU MINI PLUG (MIC OUT) RED C3 D1 -1 -2 E D2 R204 SW2(POWER) ON OFF R104 D3 ON BATTERY CHECK LAMP R3 D 1-679-165- 11 (11) 1-679-165- 11 (11) AMP BOARD (CONDUCTOR SIDE) F G LITHIUM BATTERY CR-2025 3V H I 4 ECM-S930C 3-2. SCHEMATIC DIAGRAM (DIRECTIVE ANGLE) (POWER) (POWER) Note on Printed Wiring Boards: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. z : Through hole. • • : Pattern from the side which enables seeing. Caution: Pattern face side: (Conductor Side) Parts face side: (Component Side) Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • C : panel designation. • A : B+ Line. • Power voltage is dc 3 V and fed with regulated dc power supply from battery terminal. • Voltage is dc with respect to ground under no-signal (detuned) condition. • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. • Signal path. F : AUDIO 5 ECM-S930C SECTION 4 EXPLODED VIEWS NOTE: • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • Accessories and packing materials are given in the last of this parts list. 14 11 15 18 12 12 13 MIC101 17 19 10 9 8 20 16 11 2 7 22 21 Q101 1 MIC201 6 1 Q201 4 21 22 20 3 5 Ref. No. Part No. Description * 1 * 2 3 4 5 3-222-928-01 1-679-165-11 3-224-339-02 1-550-104-33 3-222-923-01 HOLDER, UNIT AMP BOARD SHEET, BATTERY HOLDER, BATTERY LID, BATTERY CASE 6 7 8 * 9 10 3-222-907-01 3-222-926-01 3-222-921-01 3-222-927-01 3-686-420-01 HINGE KNOB, SELECTION CASE, UPPER LEVER, SELECTION SCREW (P1.4X2.5), TAPPING 11 12 13 6 3-222-929-01 GRILLE 3-222-930-01 SCREEN, GRILLE 3-222-922-01 CASE, LOWER Remark Ref. No. 14 15 16 17 18 19 20 21 * 22 MIC101 Part No. Description 1-790-506-21 X-3379-657-1 3-222-925-01 3-222-924-01 3-318-203-94 CORD, MICROPHONE (2 CORE) HOLDER ASSY, SHOE KNOB, POWER WINDOW, LED SCREW (B1.7), TAPPING Remark 7-621-259-25 2-545-447-01 2-523-713-00 2-532-219-00 8-814-289-90 SCREW +P 2.6X4 HOLDER, CAPSULE TERMINAL TERMINAL, GROUND CAPSULE, MICROPHONE CU14-03 (L-CH) MIC201 8-814-289-90 CAPSULE, MICROPHONE CU14-03 (R-CH) Q101 8-729-037-42 FET 2SK1578-A Q201 8-729-037-42 FET 2SK1578-A ECM-S930C SECTION 5 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable • CAPACITORS uF : µF • COILS uH : µH Ref. No. Part No. * 1-679-165-11 AMP BOARD *********** • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. Description Remark Ref. No. Part No. AMP When indicating parts by reference number, please include the board. Description Remark MISCELLANEOUS *************** 1-550-104-33 HOLDER, BATTERY < CAPACITOR > C1 C2 C3 C4 C101 1-127-573-11 1-125-839-11 1-164-505-11 1-125-839-11 1-162-964-11 CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP 1uF 47uF 2.2uF 47uF 0.001uF 10% 20% 20% 10% 16V 6.3V 16V 6.3V 50V C102 C103 C201 C202 C203 1-104-760-11 1-163-009-11 1-162-964-11 1-104-760-11 1-163-009-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.047uF 0.001uF 0.001uF 0.047uF 0.001uF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V 14 1-790-506-21 CORD, MICROPHONE (2 CORE) MIC101 8-814-289-90 CAPSULE, MICROPHONE CU14-03 (L-CH) MIC201 8-814-289-90 CAPSULE, MICROPHONE CU14-03 (R-CH) Q101 8-729-037-42 FET 2SK1578-A Q201 8-729-037-42 FET 2SK1578-A ************************************************************* ACCESSORIES & PACKING MATERIALS ******************************** 3-229-590-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH, SPANISH) 3-926-629-03 POUCH, CARRYING < DIODE > D1 D2 D3 8-719-049-09 DIODE 1SS367-T3SONY 8-719-072-95 DIODE 015AZ3.9-X-TPL3 8-719-052-72 LED CL-220HR-C (ON) < RESISTOR > R1 R2 R3 R101 R102 1-216-832-11 1-216-813-11 1-216-833-11 1-216-994-11 1-216-817-11 METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP 8.2K 220 10K 13K 470 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R103 R104 R201 R202 R203 1-216-817-11 1-216-828-11 1-216-994-11 1-216-817-11 1-216-817-11 METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP 470 3.9K 13K 470 470 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R204 1-216-828-11 METAL CHIP 3.9K 5% 1/16W < SWITCH > SW1 1-762-741-11 SWITCH, SLIDE (DIRECTIVE ANGLE) SW2 1-572-018-11 SWITCH, SLIDE (POWER) ************************************************************* 7 ECM-S930C REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. 1.0 8 Date 2001. 03 Description of Revision New