Download How to write (and read) audio specifications Introduction About this document

How to write (and read) audio
specifications
an Audio Precision White Paper by David Mathew
ap.com
Introduction
About this document
At Audio Precision, the analyzers we make are
recognized around the world as the standard in audio
test and measurement. Specifications, then, are very
important to us. Engineers use our equipment to
compose their own specifications for the audio devices
they design. They use our equipment to verify that their
manufacturing processes are correct, and that their
products meet the goals they have set. They use our
equipment to characterize their products’ competitive
advantages, and they publish the specifications they
derive as advertising bullet points. So we are very careful
in how we spec our own analyzers, and we have
developed some strong opinions about how speccing
ought to be done.
This document discusses how to write audio
specifications, and how to read them.
Specifications are necessary for every manufacturer, for
every product. Internal engineering specs define the
product and provide benchmarks for manufacturing
quality assurance. Published specifications, usually less
complete and rigorous than the engineering specs,
inform the user of the device’s capabilities and
limitations with the goal of safe and proper operation.
Of course, a published spec is also a powerful sales tool
for an audio device. What we read in an advertisement
or even a data sheet might be, well, shaded a bit, in an
attempt to place a device in an attractive position
without actually lying. This tension between truth and
marketing is especially evident in audio products
targeted toward home entertainment use, as ordinary
consumers are typically less informed than audio
engineers, and less adept at interpreting arcane lists of
numbers.
In the professional and commercial audio fields, the
tendency to use dubious power output ratings is
certainly much lower than in the consumer goods sector;
but a cursory sampling of pro audio, industrial audio and
communications audio product specifications reveals
incompleteness, inconsistency and just plain sloppiness,
both in which specs are chosen and how they are
expressed.
•
•
•
•
•
•
First, a look at our recommendations for writing
specifications.
What should good specifications look like?
What are typical values?
Appendix: audio standards.
Appendix: THD and THD+N.
Glossary: explanations of some of the
measurements, standards and units found in
audio specifications.
Recommendations for writing
specifications
We consider these guidelines as we write our own
specifications, and think about them when we read
specifications from other manufacturers. Each of these
recommendations is discussed in more detail following.
1.
2.
3.
4.
5.
6.
7.
Decide which characteristics are important.
Use the “best practice” method of
measurement. If a standard applies, use the
standard’s recommendation.
Spec conservatively.
State ranges and conditions; annotate when
more detail is required.
Express in standard units. Display secondary
units if applicable.
Express graphically (x-y, polar, waterfall, etc.)
when appropriate.
Use uniform units, formatting, and numerical
expressions throughout the product line.
1
Decide which characteristics are
important.
Many comments can be made about any audio device.
But which characteristics are really telling in describing a
device’s key features, its performance, its compliance
with industry standards or safety regulations?
Key features: interesting, but not performance
benchmarks
The number of inputs and outputs, their nominal levels
and connector types, the signal processing and codecs
available, the controls and displays are often included in
a list of specifications. So are application-specific details
like constant voltage outputs or IR remote compatibility,
market-specific features such as the type of mains
connector and mains voltage range. Physical
characteristics such as size and weight, environmental
limits and safety regulation compliance often make the
list as well. These are important in choosing a feature set,
but they don’t indicate actual performance levels of the
device.
Performance specifications
The details of an audio device’s tested performance are
the heart of a set of specifications. These are the
numbers that are weighed for bragging rights, for market
position, and ultimately, for a sale.
In general, the results of four categories of
measurements form the core of audio performance
specifications for any audio device:
1.
2.
3.
4.
Level, as volts (V), watts (W), or sound pressure
level (SPL).
Frequency Response, as a statement or a graph;
or at least, Frequency Range.
Distortion, as total harmonic distortion
(THD),total harmonic distortion plus noise
(THD+N), and intermodulation distortion (IMD)
of various flavors.
Noise, as an absolute voltage, as signal-to-noise
ratio (SNR), or as dynamic range.
These will be expressed differently for different classes of
device or applications, but they should always be in the
specifications in one form or another. For multichannel
devices you’ll also see separation, crosstalk, and
interchannel phase. Balanced devices may spec common
mode rejection, and devices with mechanical drives will
show “wow and flutter” figures.
Please refer to the glossary for explanations of
measurements, standards and units of measurement.
Measure according to standard or best
practice.
If a standard or regulation exists for a measurement, use
its recommendation and indicate which standard you
used. If not, most measurements have a “best practice”
method. For unusual testing methods or characteristics
new to the industry, consult the current literature and
clearly state your method, testing conditions and so on.
The role of standards
Some measurements are complicated and difficult to
perform correctly. Other measurement techniques, or
their reporting, may be disputed in the industry or can be
manipulated in the service of marketing. Cleary,
standardization of measurement methods and reporting
benefit both the manufacturer and the customer by
provide a standard reference.
Standards are revised and even withdrawn and replaced
from time to time. Spec using the latest standard that is
appropriate.
Refer to the Audio Standards appendix for more
information.
Spec conservatively.
Establish that the measurement used for a spec is not a
“best result” of a “golden unit” but is typical of the
device, achievable by any properly adjusted unit.
It’s always possible to tweak a device (by carefully
selecting components, for example) so that it will surpass
the typical performance of the devices. Do not use such
results for specifications.
It is also possible to find a “sweet spot” in a
characteristic, and report that as a performance
specification. That is misleading, even if the specification
specifically mentions the sweet spot.
2
For example, the graph above shows the residual THD+N
versus amplitude for one of our analyzer systems. For
audio analyzers, this is a key specification, one we would
like to tout.
We claim ≤ –112 dB residual THD+N in a 22 kHz
bandwidth. You can see that for most amplitudes above
400 mV the THD+N is well below this. If you are working
at a 2 V amplitude, it is about –116 dB. We find, at least
in our end of the business, that it is important not to
mislead our customers.
(The sharp inflections in the trace are artifacts of
switching between ranging circuits; the rise at the left is
the inevitable approach of the noise floor.)
State ranges and conditions.
Stating ranges and conditions is absolutely essential.
Many specifications mean nothing if these parameters
are not provided. Yet, most manufactures do not include
this information in their specifications, or what they do
include is incomplete. Are they saving ink?
Every level measurement is made at some frequency or
range of frequencies. Every frequency measurement is
made at some level or range of levels. Be very clear as to
the level and frequency of the stimulus signal, and to the
level range, bandwidth and filtering in the analyzer.
External conditions and device configuration conditions,
too, will affect device performance. What is the mains
voltage? The ambient temperature? Is the device volume
control set to low, medium or high? Are all channels
being driven, or only the channel being measured?
If there isn’t room for the conditions in the brochure,
there certainly is in the data sheet. Annotate
specifications when more detail is required. Use
footnotes or endnotes.
Here is an egregious but not uncommon example: An
expensive audiophile amplifier states its THD+N this way:
“THD+Noise
<1%”
What does that mean? There is no level or bandpass
filtering mentioned. It’s like saying “I’m taller.” THAN
WHAT?
The table below shows the THD+N results for one
channel of a home theater receiver, made under varying
conditions. Rated power (100 %) is 94 W into 4 Ω.
Note: the lower power unfiltered readings are high
primarily due to the hum and noise component
(N).
It’s clear that THD+N stated with no conditions is
meaningless.
THD+N
Bandwidth
Filter
A-weighting
Power
Stimulus
Frequency
0.65 %
no
no
100 %
1 kHz
1.85 %
no
no
10 %
1 kHz
1.92 %
no
no
10 %
10 kHz
1.06 %
no
no
10 %
100 Hz
5.66 %
no
no
1%
1 kHz
0.25 %
yes
no
100 %
1 kHz
0.01 %
yes
no
10 %
1 kHz
0.02 %
yes
no
1%
1 kHz
0.26 %
no
yes
100 %
1 kHz
0.01 %
no
yes
10 %
1 kHz
0.01 %
no
yes
1%
1 kHz
3
Express results using standard units.
Do not mix units.
Here is one of the biggest problems in interpreting
specifications: simply decoding the units chosen for the
specification, and comparing them to a similar
specification stated in different units. One unit claims
THD+N at –81 dB. Another touts a mere 0.0089 %
THD+N. Which has lower distortion and noise? (In this
case, they are the same.)
Audio levels, for example, can be expressed in pascals,
volts, watts or fractions of full scale. These can be in
absolute terms such as average, peak, peak-to-peak, rms,
and so on; or, they can be in the relative terms of
decibels or percent; on top of all that, a relative
measurement can be related to one of a number of
constants, or to a previous measurement in the same
test.
What should good specifications
look like?
The characteristics that are deemed important differ
across classes of devices. Power is important for
amplifiers; low noise is essential for microphone
preamplifiers, and intelligibility is key for
communications devices.
In this section we will look at two device classes, power
amplifiers and microphones, with a few real-world
examples in each class. We’ll see which specifications are
important and how the specifications and their
conditions should be formatted and expressed. In each
area we’ll choose three actual manufacturers’ spec
sheets and show how the spec is rendered in the real
world. It’s often not pretty. Names have been withheld
to protect the innocent and the guilty.
Display secondary units if necessary. For example,
Power Amplifiers
Residual Noise
22 Hz to 22 kHz BW, <1.0 µV [–117.8 dBu].
Remember, the four key specs are level, frequency
response, distortion and noise, stated one way or
another. Audio power amplifiers generally specify at
least these characteristics:
Express graphically (x-y, polar,
waterfall, etc.) when appropriate.
Even a clearly stated specification such as +0, –2 dB, 20
Hz to 20 kHz is nowhere near as informative as the graph
below, which shows not only the expected 2 dB droop at
the low and high ends, but also an audio-coloring 1 dB
dip in the midrange. Use a graph when you can.
•
•
•
•
Power Output
THD or THD+N
Frequency Response or Power Bandwidth
Noise, SNR or Dynamic Range
Note that not all amps are designed for high
fidelity. Amplifiers for paging systems,
communications systems or bullhorns have
different requirements.
Power Output
This is certainly the most controversial rating in
consumer audio, largely because it is the key
specification that many consumers consider when buying
a receiver: they want to know how much power it has.
Use uniform units, formatting,
numerical expressions throughout the
product line.
Messy formatting makes a lot of extra work for the
reader, even for those who can navigate through the fog
of mixed units and expressions. For the less experienced,
messy formatting is a minefield. Don’t mix expressions
like 5,000 Hz and 5 kHz; don’t say millivolts here and mV
there: be consistent.
In response to this, the marketing departments of audio
manufacturers around the world and throughout the
history of electronics have continually come up with new
and more stimulating ways to describe their products’
power output. Standards organizations and trade
commissions have been trying to referee this melee for
decades, and confusion still reigns. Refer to the Power
Ratings section of the Glossary for more on this topic.
For amplifiers destined for home entertainment use in
the US, the Federal Trade Commission has adopted what
is known as the FTC Amplifier Rule (Title 16 Part 432),
regulating power output claims in advertising.
4
So, what does the FTC Amplifier Rule tell us?
1.
2.
3.
4.
5.
6.
Power output is to be expressed as “average
continuous power in watts.”
Load impedance shall be 8 Ω or cited if
otherwise.
All associated channels must be driven at rated
power.
Power bandwidth or power frequency response
must be cited.
Maximum THD from ¼ W to rated power must
be cited.
The amplifier must be preconditioned at 1/8
rated power for 1 hour.
It’s not a bad starting place. Home entertainment
amplifiers are required to follow the rule for U.S.
advertising, and pro audio and commercial amplifier
manufacturers should start there and go beyond.
Important conditions that should be listed:
Load impedance, maximum THD or THD+N, number
of channels driven, measurement bandwidth or
power bandwidth.
THD / THD+N
THD is Total Harmonic Distortion. THD+N is Total
Harmonic Distortion plus Noise. See the Harmonic
Distortion Appendix for more about these
measurements.
Here we enter another swamp that the standards don’t
help to clarify: the FTC rule asks for THD, without
qualification. EIA/CEA-490-A wants THD, but will accept
THD+N for rating purposes if it is identified as such.
IEC60268-3 specifies THD, but will accept the THD+N
method if the noise isn’t too high. CEA-2006 will take
either. See the Standards Appendix and THD and THD+N
in the Glossary.
Important conditions that should be listed:
Stimulus frequency, level, bandwidth or weighting
filter.
Correct form:
1.26 % THD+N, 1 kHz at rated power, 22 kHz BW.
Real world specs:
Correct form:
100 W average continuous power into 8 Ω; at less
than 1 % THD+N, all channels driven, 20 Hz to 20 kHz,
FTC.
Real world specs:
•
•
•
Pro audio amplifier
600 W per channel into 8 Ω, at 0. 1 % THD+N
(1 kHz), both channels driven. [pretty clear, but
“average continuous power” seems to be
language avoided by this manufacturer,]
Home theater receiver
110 W minimum continuous power per channel,
6 Ω loads, 2 channels driven at 1 kHz, with a
maximum total harmonic distortion of 0.1%
(FTC). [FTC sums it up, but “dynamic power”
“IEC power” and JEITA power are all mentioned
on the same sheet. Since this is a 7.2 receiver
and the FTC Rule requires that “all related
channels” be driven, why are we driving only
two?]
Paging amplifier
60 W RMS output into 8 Ω, at less than 2 % THD.
[This is a mono amp, so we know all channels
are driven.]
•
•
•
Pro audio amplifier:
<0.01 % 1 kHz at rated power into 4 Ω, both
channels driven. [What bandwidth?]
Home theater receiver
0.08 % THD. [That’s all they say.]
Paging amplifier
Less than 2 % from 50 Hz to 15 kHz. [Is that the
bandwidth, or are they sweeping the
stimulus?]
Frequency Response or Power Bandwidth
Frequency response is the amplitude at a device’s
output, while a range of frequencies at a constant
amplitude is applied to the device input. It can be stated
as range of amplitudes across a range of frequencies, or
shown as a graph.
Important conditions that should be listed:
nominal measurement amplitude.
5
Correct form:
+0,–0.3 dB, 20 Hz to 20 kHz, at 2 dB below rated
power.
or, a graph like this, with clearly labeled axes.
level, bandwidth and weighting filter) are correctly
specified, these will all provide similar information.
The signal to noise ratio is exactly that: the ratio of an
audio signal level to the noise level. The signal level is
undefined, but can be the maximum output level, or the
“nominal” operating level (usually 10 to 20 dB below the
maximum output level). Signal level must be cited as a
condition for this to be meaningful.
If signal level is the maximum output level, the result is
the same as Dynamic Range.
Noise is typically measured using a bandpass limiting
filter, usually set to 20 kHz or 22 kHz, or a weighting filter
(A-weighting or ITU-IEC-468 / CCIR) is often used. These
must be specified as conditions, because the results will
vary with filtering.
Power bandwidth is similar to frequency response, but
includes the relationship to distortion and power as well.
Specifically, power bandwidth is the frequency range for
which half the rated power of an audio amplifier is
available at rated distortion. In IEC60268 the term
“power bandwidth” has been deprecated and is called
“distortion-limited effective frequency range.”
Important conditions that should be listed:
Even though power bandwidth, as defined above,
imposes its own conditions, you should state them
here. Give the rated distortion and the power level.
Correct form:
24 Hz to 19 kHz, half-power at 0.5 % THD.
Important conditions that should be listed:
Reference signal level, measurement bandwidth,
weighting filters if any
Correct form:
SNR 95 dB referenced to nominal level, ITU-468
weighting
Real world specs:
•
•
Real world specs:
•
•
•
Pro audio amplifier
Power Bandwidth (rated power at 4 Ω, 1%
THD+N) 20 Hz to 20 kHz, –0.84 dB/+0 dB
[Interesting, done at full power rather than
half, and at 1% rather than .01% (the rated
distortion).]
Home theater receiver
0.03 % THD, 50 W, 8 Ω, 10 Hz to 50 kHz. [50 W
is ½ rated power.]
Paging amplifier
Not listed.
Noise, Signal-to-Noise Ratio, Dynamic Range
Noise in audio power amplifiers is stated a number of
ways, as “Noise” or “Hum and Noise” or “Signal-to-Noise
Ratio (SNR)” or “Dynamic Range.” If the conditions (signal
•
Pro audio amplifier:
Hum and Noise (A-weighed, full power, 4 Ω) –
105 dB. [Not bad]
Home theater receiver
Signal to Noise Ratio 106 dB (LINE, IHF-A). [Does
LINE mean –10 dBV? We can only guess. IHF-A?
Is that the standard, the filter network, Aweighted? Shouldn’t we be using current
standards?]
Paging amplifier
Hum and Noise: 85 dB below rated output.
Microphones
Microphones generally specify some or all of these
characteristics:
•
•
•
•
•
•
•
•
Frequency range
Frequency response as an X-Y graph
Sensitivity
Noise
SNR
Max SPL
Dynamic range
Polar pattern
6
Note that not all mics are designed for the same
applications. Studio mics are often very quiet and
impart a characteristic “sound.” By using small
elements, measurement mics often sacrifice low
noise for very flat response. Communications
microphones are primarily concerned with the 300
to 3 kHz voice intelligibility range, and may be
more focused on acoustic noise cancellation than
microphone self-noise or flat response.
Here are commonly specified characteristics and typical
specs for three different classes of microphones.
Frequency range
A “frequency range” spec is not the same as a “frequency
response” spec. Frequency range describes the extreme
frequency limits of a device, often without stating the
amplitude. This specification is often used for
transducers such as microphones and loudspeakers that
typically have poor response (compared to electronic
devices) at the extremes of their range. When
amplitudes are stated, they can represent cutoff points
that can be down as far down as 6 dB, 12 dB or even
more.
Real world graphs:
•
Classic studio mic, cardioid selection:
•
Measurement mic:
•
Paging mic:
Important conditions that should be listed:
Amplitude variations within the range.
Correct form:
5 Hz to 20 kHz, +2, –8 dB
Real world specs:
•
•
•
Classic studio mic, cardioid selection:
5 Hz–20 kHz [How far down are the high and
low frequency extremes?]
Measurement mic:
5 Hz–20 kHz [Same question.]
Paging mic:
200 Hz–5 kHz [And same question again.]
Frequency response graphs
Microphones typically include a response graph in
addition to stating frequency range. Microphone
responses are rarely ruler-flat, and a microphone’s tonal
coloration can be an important consideration for the
user.
Important conditions that should be listed: pattern
setting (if any), filter setting (if any). Identify axes
clearly.
Sensitivity
Sensitivity is the ratio of electrical output in volts to
acoustic input (sound pressure) in pascals. For
microphones with integrated amplifiers, the gain of the
amplifier is typically part of the calculation.
Correct form:
Correct form and conditions:
50 mV/Pa
Real world specs:
•
•
•
Classic studio mic, cardioid selection:
28 mV/Pa [Well stated.]
Measurement mic:
65 mV/Pa [Well stated.]
Paging mic:
6 mV/Pa [Well stated.]
7
Noise
A microphone’s self-noise is a combination of the
thermal noise of the cartridge and (for mics that have an
integrated amplifier) the amplifier’s noise. Some
manufactures spec these separately.
Important conditions that should be listed:
Measurement bandwidth or weighting filter, if any.
The accepted decibel reference for dB SPL is 0 dB =
20 µPa, and under this assumption the reference is
rarely stated.
Correct form:
35 dB, BW, weighting (if any)
Important conditions that should be listed:
Distortion at max; once again, the accepted decibel
reference for dB SPL is 0 dB = 20 µPa, and under this
assumption the reference is rarely stated.
Correct form:
117 dB for THD=0.5 %
Real world specs:
•
•
Real world specs:
•
•
•
Classic studio mic, cardioid selection:
23 dB, CCIR; 12 dB, A-weighted [Well stated.]
Measurement mic:
25 dB, Lin; 20 dB, A [Can we assume “Lin”
means unfiltered, and “A” means
unweighted?]
Paging mic:
Not stated.
Signal-to-noise ratio.
The ratio of the nominal output level to the noise, usually
weighted and stated in dB. If the ratio is to the maximum
output level, this is the same as Dynamic Range.
Important conditions that should be listed:
Reference level of signal, measurement filters and
weighting.
Correct form:
80 dB referenced to maximum output, ITU-468
Real world specs:
•
•
•
Classic studio mic, cardioid selection:
71 dB, CCIR; 82 dB, A-weighted [Well stated.]
Measurement mic:
See Dynamic Range [An alternative to stating
SNR.]
Paging mic:
Not stated.
Maximum SPL
The sound pressure level that produces the rated
maximum distortion.
•
Classic studio mic, cardioid selection:
117 dB for THD=0.5 %; 127 dB with pad. [Well
stated.]
Measurement mic:
> 150 dB (peak) [“peak” is unclear.]
Paging mic:
Not stated.
Dynamic range.
This is an alternative to stating the noise level, the signalto-noise ratio and the maximum SPL; it states the lowest
and the highest sound pressure levels measurable below
the rated distortion.
Important conditions that should be listed:
Signal level used as reference or distortion reading at
reference level.
Correct form:
>100 dB (3% distortion limit)
Real world specs:
•
•
•
Classic studio mic, cardioid selection:
105 dB, microphone amplifier only.
Measurement mic:
> 130 dB SPL (Upper limit, 3 % distortion)
Paging mic:
Not stated.
Polar pattern
This graph is often included to show the microphone’s
response for different frequencies at different angles of
incidence.
Important conditions that should be listed:
Pattern setting, frequency legend.
Correct form:
Microphone polar patterns are typically shown like
8
the classic studio mic, below. 0° angle of incidence is
at the top, and the amplitude response of the
microphone is graphed for 360°. Several different
frequency plots are overlaid on the graph.
Real world graphs:
•
Classic studio mic, cardioid selection:
•
Measurement mic:
No polar graph, but instead these three specs:
Free-field response 0° incidence
±2 dB 12 Hz to 20 kHz
Worst case response under any conditions
±2 dB 12 Hz to 10 kHz
+2 to –8 dB, 5 Hz to 20 kHz
Paging mic:
Identified merely as “omnidirectional.”
•
Conclusion
It’s clear that there is a lot of variability in how
specifications are written.
We encourage engineers and manufacturers to keep
abreast of the standards changes, to write detailed
specifications that always include the necessary
conditions, to exercise care in choice of measurement
units and to arrange and format their specifications
sensibly.
Of course, marketeers will continue do what they must
to tell a good story and sell a million widgets. The reader
of brochures and data sheets should be wary of
specifications without the proper conditions, of mixed or
confusing units, and of any amplifier power claim that is
not stated in terms of average continuous power output.
9
Appendix A: a brief history of audio
standards
Over the years different organizations have issued
recommendations to address these issues, describing
methods for performing audio measurements and
guidelines for stating the results clearly. For example, In
the middle of the twentieth century the IHF (the nowdefunct Institute of High Fidelity) published several
revisions of an amplifier measurement standard,
culminating in IHF-A-202 in 1978. This was superseded in
1981 by EIA-RS-490 (the EIA is the Electronic Industries
Alliance), more lately succeeded by EIA/CEA-490-A, a
strong influence in the US on the FTC Amplifier Rule.
DIN 45000 standards for audio amplifiers: withdrawn and
replaced by
IEC60268, a current European standard. www.iec.ch
AES17, a current standard for digital audio
measurements. www.aes.org
FTC Amplifier Rule, www.gpoaccess.gov/ecfr/, browse to
Title 16 part 432.
Meanwhile, the Audio Engineering Society (AES) and the
Deutsches Institut für Normung (DIN) and the
International Electrotechnical Commission (IEC) were all
merrily expanding the literature. Other standards have
been written for transducers such as microphones and
loudspeakers; for audio embedded in broadcast carriers;
for audio embedded in digital bitstreams, etc.
As a result, most of the measurements cited in audio
specifications have a standard method, and in some
cases the defining standard is cited; for example, IMD is
commonly measured using the recommendation of
SMPTE, and is expressed as IMD (SMPTE); noise-shaping
delta-sigma digital converter measurements require an
analyzer equipped with a filter described in the AES17
standard; and, even today, a home theater manufacturer
specs noise using the IHF recommendation may be
expressed as “65 dB, IHF-A.” In the United States,
consumer power amplifier output ratings must follow the
FTC Amplifier Rule, and you will see expressions like “100
W (FTC).”
Be aware that even the standards can embed biases. The
standards committees are made up of human beings
who possess different opinions and varying degrees of
entanglement with audio equipment manufacturers.
Additionally, various bodies regulate electrical safety and
electromagnetic emission and other issues, and their
recommendations are often included in published
specifications.
IHFM-A-200, IHFA-A-201, IHF-A-202 standards for audio
amplifiers: superseded by EIA/CEA-490-A, a current
North American standard. www.eia.org, www.ce.org
CEA-2006, a current North American standard for
“mobile audio amplifiers” (car stereos). www.ce.org
10
Appendix B: harmonic distortion
measurements
THD+N
A simple and time-honored method of measuring
harmonic distortion is to stimulate the device with a very
pure sine wave, then remove the stimulus frequency
from the output using a very narrow notch filter. What’s
left is the distortion products and whatever noise the
device has contributed. Not only is this simple and
inexpensive, it also tells a great deal about the quality of
a device in one number. For example, two real specs:
•
one stimulus frequency, or even as a graph displaying
distortion versus level or distortion versus frequency.
Sometime manufactures confuse us by expressing the
distortion ratio in decibels rather than as a percent.
Perfectly legitimate, but requires mental conversion.
Don’t mix percentage with decibels in the same
document, please!
•
•
•
•
10 % = –20 dB
1 % = –40 dB
.1% = –60 dB
.01% = –80 dB.
Online calculators will convert other percentages for you.
Visit www.sengpielaudio.com/Calculations03.htm
Amplifier 1: THD+N <0.01%, 20 Hz to 20 kHz.
Not a bad amplifier, if power and response are
up to your needs.
•
Amplifier 2: THD+N <2%, 50 Hz to 5 kHz.
Hmm. Not for your home theater or studio, but
might do fine as a paging amp in a warehouse.
Necessary conditions for THD+N include the frequency of
the stimulus, the level of the sine wave at the output of
the device, and the bandpass or weighting filtering used
in measurement.
THD
It is also possible to measure only the distortion
products, without the noise. This was quite timeconsuming and expensive until the advent of computeraccelerated FFTs, so THD measurements were rarely
done. Now it is relatively easy to make either
measurement, with the right analyzer.
The problem is that the results are slightly different, and
that the standards vary in whether to use THD or THD+N,
and how to report it.
Our recommendation is to make a THD measurement for
FTC Amplifier Rule ratings (which require it). For
specifications not subject to the rule, choose your
method, but clearly label your results with your choice
(THD or THD+N).
Necessary conditions for THD include the frequency of
the stimulus, the level of the sine wave at the output of
the device, and how many harmonic products measured,
five being the accepted number.
In more complete specifications, harmonic distortion is
reported for more than one output level, or more than
11
Glossary
This glossary is limited to terms and concepts brought up
in this paper.
bandwidth filters
A bandwidth-limiting filter (often called a bandwidth
filter) is used in measurement to exclude frequencies
above or below the frequency range of interest, while
maintaining a flat response in the range of interest, or
“passband.” Bandwidth-limiting filters are typically used
in noise or distortion measurements to reduce the
amplitude of noise or other signals that are beyond the
range of interest, usually 20 Hz to 20 kHz.
continuous power, continuous average power
see sine output power.
DIN power
Output power as defined by DIN 45000, which has been
withdrawn and replaced by IEC60268. The output power
measurement in IEC60268 is essentially continuous
average power at rated distortion. Additionally, there is a
“short-term maximum output” characteristic described
that uses a burst signal and can produce higher power
numbers. Some manufacturers spec this as “DIN peak”
power, or just “DIN,” but the measurement is indifferent
to distortion and overstates the power. Stick with
continuous average power, and move up from the DIN
spec to the current IEC spec.
dynamic range
Dynamic range is the difference, usually expressed in
decibels, between the highest amplitude signal which a
device can output at its rated distortion, and the noise
level of the device.
dynamic power
Dynamic power replaced “music power” in IHF-A-201,
once again as an attempt to take into account the
typically low crest factor of music. A “transientdistortion” test is made, compared with the older “music
power” curve on a graph, and the worse of the two is
reported as the “dynamic power.” The term is still used
in specifications to overstate amplifier power.
frequency range
Frequency range, when used as a specified characteristic,
is a crude expression of frequency response, simply
stating the range across which the device functions.
Amplitudes within a frequency range expression may be
10 or more decibels below the amplitude at 1 kHz.
frequency response
Frequency response is typically expressed as a
statement, but is often shown as an X-Y graph as well. It
describes the amplitude variance (from a reference
amplitude, usually at 1 kHz) across a frequency range,
usually 20 Hz to 20 kHz.
IEC power
See DIN power. Some manufacturers spec the “shortterm maximum output” characteristic is as “IEC peak”
power, or just “IEC,” but the measurement is indifferent
to distortion and overstates the power. Stick with
continuous average power, which IEC60268 also defines.
IHF power
See IHF in the Standards Appendix. IHF power is a vague
term, in that the first IHFM standard defined “music
power”, which the second standard dropped as not
particularly useful, introducing “dynamic power” and
“continuous power.” So what does “IHF power” mean in
a specification? Without more information, not much.
IMD
Intermodulation distortion. IMD results when two or
more tones are combined in a nonlinear system. IMD
products are sum and difference tones, not harmonically
related to the stimulus tones. IMD is typically more
insulting to the listener than a comparable level of THD.
IMD, SMPTE and MOD
The Society of Motion Picture and Television Engineers
(SMPTE) standardized a measurement technique for IMD
in SMPTE RP 120, using, in a 4:1 ratio, a 60 Hz tone
modulated by a 2 kHz tone. The MOD IMD measurement
is similar.
IMD, DFD
The Difference Frequency Distortion method uses two
closely spaced high-frequency tones.
IMD, DIM (TIM)
Dynamic Intermodulation Distortion (DIM, also called
Transient Intermodulation Distortion, TIM) is a technique
for measuring IMD under rapidly-changing dynamic
conditions, which typically stress audio power amplifiers.
DIM uses a 3 kHz square wave modulated by a 14 kHz
sine wave of lower amplitude. The DIM measurement is
defined in IEC60268-3.
hum
Most electronic circuits have some mains power
frequency components and harmonics, called hum.
12
music power
IHFM-A-200 came up with this power definition to take
into account the typically low crest factor of music, but
within a few years dropped music power as neither
sufficient nor meaningful. The term is still used in
specifications to overstate amplifier power.
noise
All electronic circuits have some amount of broadband
noise.
PMP, PMPO
Peak Music Power, Peak Music Power Output are vaguely
defined schemes to report much higher power levels
than continuous average power. Avoid these when
writing specs and ignore when reading them. When PMP
or PMPO are listed (as in some low-end computer
speakers), divide by about 100 to get a guess at what the
continuous average power might be.
power bandwidth
Power bandwidth is the frequency range that can be
achieved sweeping an amplifier at ½ rated power, while
maintaining less than rated distortion.
rated distortion
The rated distortion is the figure the manufacturer has
chosen to claim as a minimum performance specification.
rated power
The rated power is the figure the manufacturer has
chosen to claim as a minimum performance specification.
RMS power
RMS power is a misnomer, but one used in good faith. It
means the same thing as “sine output power,” defined
below. Although the output voltage is measured in rms
volts, the result does not have the “rms” term in it. The
result is simply “watts.”
sine output power
One of several common terms for the accepted means of
measuring and reporting output power, used in EIA/CEA490-A, IEC60268-3 and the FTC Amplifier Rule. Also called
continuous power, continuous average power and
(wrongly) rms power. The stimulus signal is a sine wave.
The true rms voltage is measured across a load resistor
2
and the power is calculated by the formula V /R. The
amplifier should be capable of delivering this power
continuously for at least 30 seconds (IEC) or five minutes
(CEA-490). Visit the standards documents for detail.
SNR
Signal-to-noise ratio. Just what is says: the ratio, almost
always in decibels, between the signal level and the noise
level. The signal level should be specified; if not, a
common level is the device’s maximum output level. Two
measurements are taken: one to establish the signal
level, and one to measure the noise in the absence of
signal. Any filtering used for the noise measurement
should be stated.
spurious signals
Spurious signals refer to any signal(s) in the output of an
audio device that are not: the stimulus or program
material, harmonic distortion, intermodulation
distortion, crosstalk, hum or broadband noise.
SPL
Sound Pressure Level. Typically expressed in decibels,
referenced to a sound pressure of 20 micropascals
(20 µPa), the threshold of hearing. 94 dB SPL = 1 Pa.
THD
THD stands for Total Harmonic Distortion, a measure of
all the harmonic distortion products in the DUT’s output,
with the fundamental stimulus tone removed, and
without consideration of noise. THD measurements are
usually made with band-limiting or weighting filters.
THD+N
THD+N stands for Total Harmonic Distortion plus Noise, a
measure of everything in the DUT’s output, with the
fundamental stimulus tone removed. Noise and other
interfering signal such as hum, buzz and aliased highfrequencies are reported in the result. THD+N
measurements are usually made with band-limiting or
weighting filters. THD+N measurements are regarded as
a key benchmark of a system’s performance; the
measurement is easy to perform and widely understood,
and it shows at a glance not only distortion performance
but also indicates a system’s immunity (or lack of it) to
noise and other interfering signals.
weighting filters
A weighting filter has a specific response, with the effect
of amplifying some frequencies and attenuating others.
For audio amplifiers, one of several weighting filters is
commonly used to produce a measured response that
correlates with the human hearing experience.
Weighting filters are typically used in noise
measurements.
Copyright © 2010 Audio Precision
13