Download IM-010 - Secco

IM-010
LEAVE A CLEARANCE OF
AT LEAST 12” AROUND
THE CONTROLLER
BOX TO ALLOW THE COVER
TO BE REMOVED FOR
MAINTENANCE.
VOLTAGE
SELECTOR
115/230 VAC
NOTES:
INSTALLATION OF A GOOD
QUALITY ALARM SYSTEM
IS STRONGLY SUGGESTED
TO WARN OF POWER
FAILURES AND HIGH/LOW
TEMPERATURES.
230V
CONNECTION FOR
COMMUNICATIONS
BOARD COMLINK-1
CARD
4
POT.
+
0-10V
IN GND + GND
ALARM
NC C NO
L1 L2/N
DO NOT GROUND THE
SHIELD ON THE
POTENTIOMETER WIRE.
ISOLATE THE WIRE FROM
ALL HIGH VOLTAGE SOURCES.
{
REFER TO THE
DIAGRAMS BELOW
TO CONNECT THE
POTENTIOMETER
{
GND
L2 ( N )
L1
ALARM
SUPPLY
REFER TO THE
DIAGRAMS BELOW
TO CONNECT THE
ACTUATOR
0-10V0-10V+
to MODULE 3 terminal
of the ventilation controller
to MODULE 2 terminal
of the ventilation controller
0-10V
ALARM
NC C NO
CONNECT THE PROPER
TERMINALS (0-10V OR MODULE)
DEPENDING ON THE CHOSEN
COMMUNICATION METHOD.
1
L1 L2/N
2
3
4
POT.
+
0-10V
IN GND + GND
ACTUATOR
ALARM
NC C NO
IN OPN CLO RET
IT IS IMPORTANT TO
CONNECT THE WINCH
RETURN TERMINAL
TO THE ACTUATOR
L1
IT IS IMPORTANT TO
CONNECT THE WINCH
RETURN TERMINAL
TO THE ACTUATOR
{
L1
WHITE
(N)
GREEN
GND
THE RESISTANCE
INCREASES
ON “GND” and “IN”
WHEN OPENING
N
18AWG
SHIELDED
CABLES
ACTUATOR
POWER SUPPLY
115 VAC
{
ACTUATOR
POWER SUPPLY
115 VAC
RED
BLACK
{
POTENTIOMETER
THE RESISTANCE
INCREASES
ON “GND” and “IN”
WHEN OPENING
L1 L2/N
GND
YELLOW
18AWG
SHIELDED
CABLES
Vic Jack Actuator
with potentiometer
(1, 5 or 10 Kohms, 10 Turns)
To communication
(MODULE) terminals
1
of a ventilation controller .
MODULES
ACTUATOR
IN OPN CLO RET
OPEN = RED
IN GND + GND
OR
WHITE
POT.
+
{
1
COMMUNICATION BETWEEN
THE IM-010V AND THE
VENTILATION CONTROLLER
CAN EITHER BE ESTABLISHED
WITH A 0-10V SIGNAL OR BY
USING THE COMMUNICATION
BUS.
To 0-10V output of
the ventilation controller 1 .
CLOSE = BLACK
4
RED
3
BLACK
2
YELLOW (WIPER)
MODULES
{
CONTROLLER
POWER SUPPLY
230 VAC (115VAC)
VON WEISE V-76-115 ACTUATOR- AC MOTOR
VIC JACK ACTUATOR- AC MOTOR
1
PROVIDE A SURGE
PROTECTION (INCLUDING
LIGHTNING PROTECTION)
FROM THE POWER SUPPLY
TO THE CONTROLLER AND
FROM THE CONTROL
TO THE SENSORS. CONSULT
A CERTIFIED ELECTRICIAN
IF REQUIRED.
ACTUATOR
IN OPN CLO RET
OPEN
3
CLOSE
2
ORANGE
MODULES
1
BLUE (WIPER)
DO NOT DRILL THE SIDE
OF THE UNIT CONTROL.
USE AVAILABLE KNOCKOUTS
AT THE BOTTOM OF THE UNIT.
Von Weise Actuator V-76-115
115 VAC with potentiometer
(1, 5 or 10 Kohms, 10 Turns)
WIRING DIAGRAM
IM-010
#891-00081
Rev.01
WIRING DIAGRAM
#891-00081
IM-010
Rev.01
WHITE
ORANGE
3
4
+
4
+
THE RESISTANCE
INCREASES
ON “GND” and “IN”
WHEN OPENING
0-10V
THE RESISTANCE
INCREASES
ON “GND” and “IN”
WHEN OPENING
ACTUATOR
POWER
SUPPLY
115 VAC
{
ACTUATOR
IN OPN CLO RET
ALARM
IN OPN CLO RET
NC C NO
18AWG
SHIELDED
CABLES
{
L1
N
GND
L1 L2/N
ACTUATOR
N
{
GND
+
+
G
FILTER
ACTUATOR
-
G
ACTUATOR
POWER SUPPLY
230 VAC (115 VAC)
ACTUATOR
L1
L2 ( N )
18 TO 36 VDC
TRANSFORMER
L
-
FILTER
18 TO 36 VDC
TRANSFORMER
N
IT IS IMPORTANT TO
CONNECT THE WINCH
RETURN TERMINAL
TO THE ACTUATOR
L1 L2/N
IT IS IMPORTANT TO
CONNECT THE WINCH
RETURN TERMINAL
WITH THE ACTUATOR
L1 L2/N
L1
N
L
IN OPN CLO RET
GND
ACTUATOR
ACTUATOR
POWER
SUPPLY
115 VAC
ALARM
18AWG
SHIELDED
CABLES
ALARM
NC C NO
18AWG
SHIELDED
CABLES
NC C NO
IN GND + GND
POT.
0-10V
IN GND + GND
POT.
0-10V
+
IN GND + GND
POT.
4
POTENTIOMETER
(1, 5 or 10 Kohms, 10 Turns)
3
POTENTIOMETER
(1, 5 or 10 Kohms, 10 Turns)
2
2
WIPER
MODULES
1
1
MODULES
Von Weise
actuator V-76-30
36VDC Motor with
potentiometer
(1, 5 OR 10 Kohms, 10 Turns)
{
BLUE (WIPER)
BLACK
RED
3
THE RESISTANCE
INCREASES
ON “GND” and “IN”
WHEN OPENING
WIPER
OPEN
2
OPEN
CLOSE
MODULES
CLOSE
OPEN
+18VAC
1
+18VAC
POTENTIOMETER
VON WEISE V-76-30 ACTUATOR - DC MOTOR
-18VAC
CLOSE
-18VAC