Download HiQu Digital wired remote

HiQu
®
Digital
Wired remote dual switch
The Waste Electrical and Electronic Equipment (Producer Responsibility) Regulation 2004
This product is outside the scope of the European Waste Electrical and Electronic Equipment Directive as interpreted within the UK.
In the UK this product can therefore be disposed of through commercial non-WEEE waste facilities.
The original manufacturer does not accept any liability under the WEEE directive.
HiQu Digital wired remote dual switch installation instuctions
page 1
Important information
The HiQu Digital wired remote dual switch is a remote button which provides a secondary method of the start/stop
control to HiQu Digital shower and bath systems. The wired remote dual switch may be sited inside the showering or
bathing area, as long as it is not subjected to continuous spray, or sited outside the showering or bathing area – up to
10m cable length run from the HiQu Digital processor site.
This product must be installed by a competent person in accordance with all relevant current Water Supply Regulations.
ALL SHOWERS REQUIRING AN ELECTRICAL CONNECTI0N MUST BE INSTALLED BY A QUALIFIED PERSON
FOLLOWING THE LATEST REVISION OF BS 7671 (WIRING REGULATIONS) AND CERTIFIED TO CURRENT
BUILDING REGULATIONS.
The HiQu Digital wired remote dual switch is suitable for domestic use only.
HiQu Digital wired remote dual switch installation instuctions
page 2
Step-by-step instructions
Digital wired remote dual switch
!
In addition to the guide below it is essential that the written
instructions below are read and understood and that you have
all the necessary components (shown below) before commencing
installation. Failure to install the product in accordance with these
instructions may adversely affect the warranty terms and
conditions. Do not undertake any part of this installation unless
you are competent to do so. Prior to starting, ensure that you are
familiar with the necessary plumbing regulations required to install
the product correctly and safely.
!
THE HIQU DIGITAL PROCESSOR MUST BE ISOLATED FROM THE
MAINS POWER SUPPLY PRIOR TO INSTALLING THE HIQU
DIGITAL WIRED REMOTE DUAL SWITCH.
Components
Literature not shown
1
Using the back plate as a template,
mark out the position of the fixing
screws and 20mm diameter cable
rear entry point. Prepare the fixing
points using the fixings provided,
if suitable.
2
Prepare a suitable route and install
the low voltage data cable leaving
a working end of at least 70mm
including the connector plug.
!
Data cables that are chased into the wall or are surface sited
must be protected by suitable sheathing or conduit.
HiQu Digital wired remote dual switch installation instuctions
page 3
3
Pull the data cable through before
securing the back plate to the wall
using the screws provided.
4
Push the data cable plug into the
5
Locate the top of the button
back of the button fully home.
assembly onto the back plate
assembly and press to lock into
place.
!
To release the button cover, insert a
small flat bladed screw driver into
the small opening at the base of
the button and press to release.
6
The Digital processor features a
secondary data cable socket next
to the main data cable connection
for use with the Digital wired
remote dual switch start/stop
controller. Carefully snap and
remove the entry pillar and connect
the cable to the socket as shown.
7
Prior to commissioning the HiQu Digital wired remote dual switch
following the procedure opposite, please refer to the HiQu Digital
shower instructions to complete the installation of the Digital
processor.
HiQu Digital wired remote dual switch installation instuctions
page 4
Aqualisa Products Limited
The Flyer’s Way
Westerham Kent TN16 1DE
Sales enquiries: 01959 560010
Republic of Ireland 01-864-3363
Customer helpline: 01959 560010
Republic of Ireland 01-844-3212
Brochure Hotline: 0800 652 3669
Website: www.aqualisa.co.uk
Email: [email protected]
Please note that calls may be recorded for training and quality purposes
The company reserves the right to alter, change or modify the product specifications without prior warning
® Registered Trademark Aqualisa Products Limited