Download Прожектор WW8004 RGB 220V (24x3W, 990mm)

Прожектор WW8004 RGB 220V (24x3W, 990mm)
Product Introduction:
Our LED Wall Washers adopt high Power LED
in RGB as light source. It could be used in indoor or
outdoor. The LED Wall Washer is our patented product with uniform mixed lights, distinctive appearance and so on. Its effect of mixed light used our company Self-developed Integral and obliquitous reflector. To break with traditional way whose effect of mixed light is used LED Lens.
The body of this product adopts distinctive style design with smooth lines, fine appearance and so
on. The whole lamps and lanterns looks very good.
It is used matching bracket to achieve installing beside the wall or vertical the ground. It needn’t
adjust the angle to get very good lighting effect. It is used hand in hand connection among lights
with conveniently installing and operating simply.
Single color LED Wall Washer is lighting once power-on. RGB LED Wall Washers are of 13 kinds of
effects inside, connecting consoles outside, and so on for your choice. It could be integral controlling or step-shaped changing controlling.
The mixed changing color is composed by red, green and blue with many kinds of lighting presenting continuous to beautify the environment and dot the city.
Application:
LED wall washer can be widely used for indoor ,outdoor decoration and stage, meeting room,
exhibition lighting, ancient buildings and cultural plaza and other places.
Technical parameters:
Parameter
Value
Input voltage
AC90~260V (50/60Hz)
Working voltage
DC24V
Maximum power
78Watts
LEDcurrent
350 mA
Light source
RGB High Power LED
24LED
Luminous Flux (LM)
760 Lm
LED Projecting Way
Self-developed Integral and obliquitous reflector
Signal Standard
DMX512
Control Way
Outside using DMX Control Box or DMX512
Standard Console; Master-Slave Services
Temperature for working
-20oC ~ +45oC
IP Rank
IP65
Connection Ports:
•
•
•
•
Power input port with 3-pin male waterproof connector
Power output port with 3-pin female waterproof connector
Standard DMX signals input port with 3-pin male waterproof connector
Standard DMX signals output port with 3-pin female waterproof connector
Button Functions:
Each RGB wall washer has 14 color modes for options.Please refer to the MODE DETAILS Press
these 2 button for different choices. Button 1 is for increasing, and button 2 is for decreasing.
Please see the below :
Interface display functions Instructions:
001 ~ 512: means the wall washer is on the mode of being controled, in this mode, the wall
washer will be controlled by the main wall washer.
H-1 ~ H-D: main control mode,in this mode,all the following connected wall washer,can change
the same lighting effect as the first one.
Modes Details:
001~512:
H-1:
H-2:
H-3:
H-4: H-5: H-6: DMX code
Single Red
Single Green
Single Blue
Single Yellow
Single Cyan
Single Purple
H-7:
H-8:
H-9:
H-A:
H-B:
H-C:
H-D:
Single White
7-color Jumping changing
3-color Jumping changing
7-color Gradual changing
3-color Gradual changing
7-color Flash changing
3-color Flash changing
Dimention (unit: mm):
Attention:
• When you use the product, please make sure it works in good condition.
• Each single row wall washer takes up 3 addresses, the first wall washer’s address plus 3 is the
address for the next one.
• If you want all connected wall washers to change color together, you should set the same address for all the wall washers.
• If you want all connected wall washers to change color together, you should set the same address for all the wall washers.
• Please set the address from 001 to 512.
• The maxinum address should be less than 510.
• There should be only one main wall washer as a key controller (the wall washer works in main
control mode, dmx512 control box or dmx console).
• When many single row wall washers connected together, the connection please refer to the connection diagram.
• The connection cable between two DMX Signals amplifier, or between DMX console and DMX signal amplifier, It can’t exceed 100m; The distance between the first DMX signals amplifier or DMX
console and the last wallwasher can’t exceed 100m.
Connection Layout:
• Method 1
• Method 2
Warning:
1. When the product in the packing box, please do not connect the power source;
2. Before installing please do not connect the high-voltage power supply, and make sure the equipment connect ground;
3. Replace any protection cover which is bursted;
4. Attention fire protection, against electricity and quakeproof.
5. Before installing the product please read the instruction carefully, also plsease preserve this
document for future reference.
Attention:
Corrosiveness or soluble chemicals will make the outer covering protection of lamps to be destructed.
Normal wroking temperature: - 35oC ~ +40oC , the humidity: 0~95%, if surpasses this prescribed limit, it will have the disadvantageous influence to the life time. Storeing temperature:
-35 ~ +70oC.
We are not be responsible for the aftereffect which use any correlative accessory are not provided
by our company.