Download 70-6910 2008- 2009 Tradeline Catalog

Modutrol IV Motors
Approvals:
CE: Report: GV97-011
Control Signal
Includes
Comments
Used With
Q181A1007
SPST, On/Off switch
Cover
For controlling one modutrol motor
Series 90
Q181A1015
SPST, On/Off switch
Cover
For controlling two modutrol motors
Series 90
Q181A1064
SPST, On/Off switch
—
For controlling up to three modutrol motors
Series 90
Q181A1072
SPST, On/Off switch
—
For controlling up to four modutrol motors
Series 90
Hydronic Controls
Product Number
* TRADELINE models • SUPER TRADELINE models
Q209 Manual Potentiometer for Modutrol Motors
Approvals:
CE: Report: GV97-011
Q209E
Includes
Used With
Q209A1022
SPST, On/Off switch
150 ohm Potentiometer, leadwires and bracket
M744, M745, M941, M944, M945,
M954, M955
Q209A1030
SPST, On/Off switch
300 ohm Potentiometer, leadwires and bracket
M744, M745, M941, M944, M945,
M954, M955
Q209E1002
SPST, On/Off switch
150 ohm Potentiometer, factory mounted on a wring cover box
—
Q209E1010
SPST, On/Off switch
300 Ohm Potentiometer, Factory Mounted on a wiring cover box —
Pneumatic Controls
Control Signal
Commercial
Components
Product Number
* TRADELINE models • SUPER TRADELINE models
443
Industrial Combustion
Controls
70-6910
Building Automation
Application Type: Electro-mechanical
Dimensions, Approximate: 3 1/4 in. high x 3 3/8 in. wide x 3 7/8 in.
deep (83 mm high x 86 mm wide x 98 mm deep)
Electrical Connections: Screw terminals
Mounting: Internal mount to Modutrol IV Motors
Weight: 0.2 lb
Water
Controls
Used to limit minimum position of a proportioning Modutrol motor.
• Mount directly in motor.
• All wiring is accomplished within motor wiring compartment.
• Color-coded leadwires.
Q209A
Residential
Combustion Controls
Application Type: Electro-mechanical
Dimensions, Approximate: 3 3/16 in. high x 3 1/4 in. wide x 3 3/8 in.
deep (81 mm high x 83 mm wide x 86 mm deep)
Electrical Connections: Screw terminals
Mounting: External mount to Modutrol IV Motors
Weight: 1.38 lb
Indoor Air Quality
Controls one to four Modutrol (series 90) motors from one master
motor.
• Compatible with Modutrol III and Modutrol IV motors.
• Mounts on master motor and operates controlled motors in unison or
in sequence.
• Controls motors with mechanical balance relay and solid state drive
circuit.
• Use with 24V motors.
Home
Controls
Q181 Auxiliary Potentiometer for Modutrol Motors
Modutrol IV Motors
Q607 Auxiliary Switches for Modutrol Motors
For control of auxiliary equipment as a function of motor shaft
position.
• Compatible with Modutrol III and Modutrol IV motors. (Requires
220738A adapter bracket for use with Modutrol IV motors).
• Micro Switch precision switches, adjustable.
• Indicate motor position by use of a scale plate anchored to a
common shaft, which allows Q607 to be adjusted for operational
sequence before mounting.
• Adjustable plate allows universal mounting on either end of motor.
• Wrap-around cover for easy access to switch adjustments and
wiring.
• Maintenance-free protection of the switches and cams.
Application Type: Electro-mechanical
Dimensions, Approximate: 6 7/16 in. high x 5 3/16 in. wide x 2 1/8 in.
deep (164 mm high x 132 mm wide x 54 mm deep)
Auxiliary Switch Ratings AFL - 120 Vac: 9.8 A
Auxiliary Switch Ratings ALR - 120 Vac: 58.8A
Auxiliary Switch Ratings AFL - 240 Vac: 4.90A
Auxiliary Switch Ratings ALR - 240 Vac: 29.4A
*
*
Electrical Connections: Screw terminals
Mounting: Cover or gear end
Weight: 2.5 lb
Approvals:
Canadian Standards Association: Certified: File No. LR1620
Underwriters Laboratories Inc. Listed File: E4436, Guide: XAPX2
Product Number
Internal
Auxiliary
Switch
Control Signal
Q607A1050
1
Q607A1076
1
Q607B1067
2
SPST, On/Off switch
Revised mounting bracket
Q607B1083
2
SPST, On/Off switch
With adapter for cover end spring return motor and —
revised mounting bracket
Q607C1009
1
SPST, On/Off switch
Special terminal panel and metric grounding screws —
Q607D1008
2
SPST, On/Off switch
Special terminal panel and metric grounding screws —
Includes
Comments
SPST, On/Off switch
Revised mounting bracket
Post 1969 Honeywell Modutrol Motors
SPST, On/Off switch
With adapter for cover end spring return motor and Post 1969 Honeywell Modutrol Motors
revised mounting bracket
* TRADELINE models • SUPER TRADELINE models
444
customer.honeywell.com
70-6910
Pre/Post 1969 Honeywell Modutrol
Motors
Modutrol IV Motors
Home
Controls
Q7130; Q7230; Q7330 Interface Modules for
Series 90 Modutrol IV Motors
Q7130A
Q7230A
Control Signal
Used With
Q7130A1006
Provides selectable voltage ranges: 4 to 7, 6 to 9, or 10.5 to 13.5 Vdc. Adapts M91XX to
function as M71XX model
Series 90 for conversion to Series 70
Q7230A1005
Provides adjustable zero & span, voltage or current control (includes 2-10 Vdc or 4-20
mA). Adapts M91XX to function as M72XX model.
Series 90 for conversion to Series 70
Q7330A1004
Provides interface to W936 Control. Adapts M91XX to function as M73XX model.
Series 90 for conversion to Series 70
* TRADELINE models • SUPER TRADELINE models
Water
Controls
Product Number
Hydronic Controls
Q7330A
Residential
Combustion Controls
Application Type: Electric
Dimensions, Approximate: 3.78 in. (96 mm) wide, 1.93 in. (49 mm)
deep, 1.58 in. (40mm) high
**Fits inside wiring junction box of Modutrol IV Motor
Ambient Temperature Ratings: -40 F to +150 F (-40 C to +66 C).
Electrical Ratings: Power Supply: 24 Vac, 50/60 Hz.
Power Consumption: 2 VA.
Input Impedance:
Q7130A: >100K ohms.
Q7230A: Voltage input >100K ohms;
Current input = 67 ohms.
Electrical Connections: Terminal Board
Frequency: 50 Hz; 60 Hz
Mounting: Mounts to quick-connects inside Mod Motor
Ambient Temperature Range: -40 F to +150 F (-40 C to +60 C)
Weight: 0.3 lb
Indoor Air Quality
For converting series 90 Modutrol IV motors to series 70
(electronic) control.
• Mounts and works inside wiring box of any series 90 Modutrol IV
Motor.
• Protected from weather by motor's NEMA 3 wiring box.
• Mates to motor's quick-connect terminals and provides screw
terminals for control wiring connections.
• Features solid-state circuitry with surface mount components.
• Plastic enclosure provides easy handling and protection for circuitry.
• Includes (except Q7330A) reversing switch to allow replacement of
electrically normally open or electrically normally closed motors.
Building Automation
Commercial
Components
Pneumatic Controls
445
Industrial Combustion
Controls
70-6910
Modutrol IV Motors
Interface Module Cross Reference and Usage Chart
.
Product Number
Application
Q7130A1006
Provides selectable voltage ranges: 4 to 7, 6 to 9 or 10.5 M734H1034, M734H1000
to 13.5 Vdc. Adapts M91XX Modutrol IV motor to function
M734H1018
as M71XX model for M734H,J; M744D; M745G,P
M734H1026
replacements.
Q7230A1005
Q7330A1004
446
Replaces
Provides adjustable zero and span, voltage or current
control (includes 4 to 20 mA and 2 to 10 Vdc). Adapts
M91XX Modutrol IV motors to function as M72XX model
for M744S,T,Y; M745S,T,Y replacements.
Provides interface to W936 Control. Adapts M91XX
Modutrol IV motor to function as M73XX model for
M734D; M744A; M745A replacements.
customer.honeywell.com
70-6910
Replaces
Use With
M7164G1006
M9164D1009
M7164G1014
M7164G1022
M734J1015
M7164A1009
M734J1031, M734J1023,
M734J1056
M7164A1017
M734J1007, M734J1072
M7164B1007
M744D1011, M744D1003
M7184A1005
M745G1007
M7186G1000
M9186G1006
M745P1007
M7185A1004
M9185D1004
M9184D1021
M744S1005
M7284A1004
M744S1013
M7284A1012
M744T1004
M7284C1000
M744T1012
M7284C1018
M744Y1009
M7284Q1009
M744Y1017
M7284Q1017
M745S1002
M7285A1003
M745S1010
M7285A1011
M745T1001
M7285C1009
M745T1019
M7285C1017
M745Y1006
M7285Q1008
M745Y1014
M7285Q1016
M734D1004
M7364A1007
M734D1012
M7364A1015
M734D1038
M7364A1023
M744A1006
M7384A1003
M744A1014
M7384A1011
M745A1003
M7385A1002
M745A1011
M7385A1010
M9184D1021
M9185D1004
M9164D1009
M9184D1021
M9185D1004
Kit Mounted Motors
Home
Controls
M436; M836 Damper Motors
Residential
Combustion Controls
Motor Shafts: 2
Shaft Shape: Hexagonal
Angle of Rotation (Stroke Max (deg)): 75
Angle of Rotation (Stroke Min (deg)): 75
Operating Temperature Range: 32 F to 125 F (0 C to 52 C)
Operating Humidity Range (% RH): 5 to 95% RH
Weight: 4 lb 10 oz (2.1 kg)
Approvals:
Underwriters Laboratories Inc. Listed File: E4436, Guide: XAPX
(Nm)
*
M436A1116
20 lb-in.
2.3 Nm
120 Vac
40 sec
25 sec
Open:
30 sec
0.37 A
0.12 A
28 W
8.5 W
—
—
*
M436A1124
20 lb-in.
2.3 Nm
240 Vac
40 sec
25 sec
Open:
30 sec
0.19 A
0.06 A
29 W
8.5 W
—
—
M436A1140
20 lb-in.
2.3 Nm
220 Vac
55 sec
25 sec
Open:
30 sec,
Close:
25 sec
0.21 A
0.062 A
30 W
8.5 W
Ground
Series
and cover 40, 80
screw
circuits
*
M836A1042
20 lb-in.
2.3 Nm
24 Vac
40 sec
25 sec
Open:
30 sec
1.85 A
0.6 A
28 W
8.5 W
—
—
*
M836B1033
15 lb-in.
1.7 Nm
24 Vac
40 sec
25 sec
Open:
25 sec
1.34 A
0.73 A
20.3 W
11.2 W
—
—
Nominal Current Nominal Power
Timing
Draw (amps)
(watts)
Opening,
Nominal
Used
(sec)
Opening Holding Opening Holding Includes With
Water
Controls
Product Number (lb-in.)
Spring
Return
Run Time Timing
(Maximum (Maximum
Voltage (sec))
(sec))
Torque Rating
Hydronic Controls
Dimensions, Approximate: 4 1/2 in. high x 4 5/8 in. wide x 3 3/4 in.
deep (114 mm high x 118 mm wide x 95 mm deep)
Fail Safe Mode: Spring Return
Control Signal: Two position, SPST
Internal Auxiliary Switch: 1
External Auxiliary Switches Available: Yes
Torque Rating, Breakaway: 30 lb-in.
Electrical Connections: Screw terminals
Frequency: 60 Hz
Mounting: Foot-mounted
Indoor Air Quality
Spring return motors for two-position back draft, outdoor air
changeover, zone, or minimum position damper control.
• Operate outdoor air dampers for combustion or makeup air in
residential and light industrial applications.
• Operate changeover dampers for heating and cooling systems.
• Operate minimum position dampers for ventilation and similar
applications.
• Include internal SPDT switch for controlling auxiliary equipment,
additional motors, or to provide a burner interlock switch.
• Spring returns motor to start position on power failure.
• Drive shafts located on both sides of motor.
• Adjustable auxiliary switch for cascading motors or operating
auxiliary equipment.
• Thermal breaker for overload protection during lifting stroke or if
motor stalls.
Building Automation
* TRADELINE models • SUPER TRADELINE models
Commercial
Components
Pneumatic Controls
447
Industrial Combustion
Controls
70-6910
Kit Mounted Motors
M835 Two-Position Zone Damper Actuator
Two-Position Zone Motor, used with two-wire, 24-volt room
thermostat or other controller for two position damper control.
• Controls zone or changeover damper in heating and air conditioning
systems, and control gates on feeders.
• SPST end switch makes within 20 sec of full open, breaks within 20
sec after start of closing stroke.
Dimensions, Approximate: 5 1/2 in. high x 4 1/4 in. wide x 2 5/8 in.
deep (140 mm high x 108 mm wide x 67 mm deep)
Fail Safe Mode: Spring Return
Control Signal: Two position, SPST
External Auxiliary Switches Available: No
Torque Rating, Breakaway: 30 lb-in.
Electrical Connections: Lead wire in conduit box
Frequency: 60 Hz
Mounting: Foot-mounted
Motor Shafts: 2
Shaft Shape: Round
Angle of Rotation (Stroke Max (deg)): 60
Angle of Rotation (Stroke Min (deg)): 75
Operating Temperature Range: Cooling: 140 F, Heating: 200 F
(Cooling: 60 C, Heating: 93 C)
Operating Humidity Range (% RH): 5 to 95% RH
Torque Rating
Product Number
(lb-in.)
Nominal Power (watts)
(Nm)
4 lb-in.
0.45 Nm
* M835A1051
* TRADELINE models • SUPER TRADELINE models
Voltage
Run Time (Maximum (sec))
Opening
Holding
24 Vac
Open: 80 sec, Close: 160 sec
27 W
8.5 W
M847 Two-Position Draft Damper Actuator
Two-Position Draft Damper Actuators. Use with two-wire 24V room
thermostats or other low voltage controllers to operate the draft
damper on solid fuel furnaces or boilers and other similar light
duty applications.
• Low voltage, spring-return damper actuator.
• Equipped with mounting bracket for wall, duct or direct appliance
mounting to control draft damper through an actuator arm or chain
linkage arrangement.
• Actuator wheel rotates in a clockwise direction (when facing the
wheel) when energized.
Dimensions, Approximate: 3 1/2 in. high x 2 5/8 in. wide x 3 5/16 in.
deep (89 mm high x 66 mm wide x 84 mm deep)
Fail Safe Mode: Spring Return
Control Signal: Two position, SPST
External Auxiliary Switches Available: No
Frequency: 60 Hz
Mounting: Foot mounted. Direct Coupled
Motor Shafts: 1
Shaft Shape: Round
Angle of Rotation (Stroke Max (deg)): 45
Operating Temperature Range: 40 F to 125 F (5 C to 50 C)
Operating Humidity Range (% RH): 5 to 95% RH
Weight: 1.75 lbs
Torque Rating
Product Number
(lb-in.)
(Nm)
Voltage
Run Time (Maximum
(sec))
Includes
M847A1072
1.9 lb-in.
0.21 Nm
24 Vac
20 sec
3.8 in. linkage arm
M847A1080
1.9 lb-in.
0.21 Nm
24 Vac
20 sec
38 in. linkage chain
* TRADELINE models • SUPER TRADELINE models
448
customer.honeywell.com
70-6910
Kit Mounted Motors
Used With
121825AA
Auxiliary crank arm assembly
M835; Q298
126809/0021
M836 Mounting Bracket
M836
126809/0021
M836 Mounting Bracket
M836
126816/0021
Clamp for M436
M436
128336/0021
Mounting Bracket for M436/M836, Increases motor height 0.5 inches.
M436, M836
16254AC
Motor mounting bracket for M436/M836.
M436, M836
198545
Motor mounting bracket for M436/M836.
M436, M836
4074BRU
Bag Assembly Extension adapter and screws for mounting Q607 Auxiliary switch to Q607; M436A
M436A Damper Motor.
M11524
4074BRU
Crank arm, heavy duty
—
4074ELY
Crank arm, infinitely adjustable
—
Hydronic Controls
4074ELR
Versa Drive Accessories
Product Number
Description
Q583C1002
Coupler and Bracket for Versadrive Actuator
Residential
Combustion Controls
Description
Indoor Air Quality
Product Number
Home
Controls
Replacement Parts and Accessories for Kit Mounted Motors
Water
Controls
Building Automation
Commercial
Components
Pneumatic Controls
449
Industrial Combustion
Controls
70-6910
Damper and Valve Linkages
Q100 Linkage
Contains necessary hardware to link Modutrol™ motors to a V51B
Butterfly Valve.
• Compatible with Modutrol III and Modutrol IV™ motors. (Requires
adapter bracket, which is standard on all Modutrol IV motors
included in this catalog unless otherwise noted.)
• Adaptable for all sizes of V51B Valves.
• Strain release and stop bracket are provided with V51B.
Linkage Type: Valve
Used with Actuator: Modutrol Motor
Product Number
Description
Q100A1015
Linkage for 2 1/2 and 3 in. butterfly valves
Q100A1023
Linkage for 4 in. butterfly valves
* TRADELINE models • SUPER TRADELINE models
Q298 Damper Linkage for Economizer Motors
Connects M833, M835, M836 or M7415 motor to 1 or 2 zone
dampers.
• May be used to link shafts of two dampers together.
• Includes pushrod, ball joints and bushings for 1/4 in. (6 mm) to 1/2 in.
(13 mm) diameter shafts.
Linkage Type: Damper
Used with Actuator: Damper Actuator (M6415, M7405, M7415,
M8415)
Product Number
Description
Includes
Q298B1065
Damper Linkage
Pushrod in variable lengths, 2 damper arms, and 2 ball joints
* TRADELINE models • SUPER TRADELINE models
450
customer.honeywell.com
70-6910
Damper and Valve Linkages
220829JCQ1 Johnson Control Valve Adapter Kit
220829LGQ1 Landis and Gyr Powers Valve Adapter Kit
220829LGQ2 Landis and Gyr Powers Valve Adapter Kit
220829LGQ3 Landis and Gyr Powers Valve Adapter Kit
Replacement Parts:
220829BCQ1 Barber-Colman Valve Adapter Kit
Bonnet
Size (in.)
Stroke
Description
Includes
Used With
*
Q5001D1000
1 3/8 in.
3/4 in.
Valve Linkage for Mod III and Mod IV motors
with 80 or 160 lb stem force
1 3/8 in. valve bracket
and Anti spin clip
V5011/V5013; Modutrol IV Motors
*
Q5001D1018
1 3/8 in.
3/4 in.
Valve Linkage for Mod IV motors with 160 or
320 lb stem force and up to 3 inch valves
1 3/8 in. valve bracket
and Anti spin clip
Valve sizes up to 3 inch; V5011/
V5013; Modutrol IV Motors
*
Q5001D1026
1 7/8 in.
1 1/2 in.
Valve Linkage for Mod IV motors with 160 or
320 lb stem force and 4, 5 or 6 inch valves
1 7/8 in. valve bracket
and Anti spin clip
4, 5 or 6 inch valves; V5011/V5013;
Modutrol IV Motors
* TRADELINE models • SUPER TRADELINE models
Water
Controls
Product Number
Hydronic Controls
220845/0767 Retainer button for Q5001
Accessories:
Residential
Combustion Controls
Linkage Type: Valve
Mounting: Linkage mounts directly to the valve bonnet; motor mounts
on linkage bracket.
Used with Actuator: Modutrol Motor
Stem Force Rating: 80 or 160 lbf (356 N or 712 N)
Ambient Temperature Range: -40 F to +150 F (-40 C to +66 C)
Indoor Air Quality
The Q5001 Valve Linkage connects a Modutrol™ Motor to a 2- or
3-way valve. It is used primarily on V5011 or V5013 steam and
water valves.
• Q5001 Valve Linkage is applicable to 2-Way or 3-Way valves in
modulating or two-position service.
• Linkage requires no adjustment when used with Honeywell valves
and Modutrol IV™ Motors.
• Q5001 Valve Linkage replaces Q601 and Q618 Valve Linkages.
• Linkage mounts directly to the valve bonnet; motor mounts to linkage
bracket.
• Easy-to-read position indicator.
• Valve stem lift height cam selectable.
• Overtravel permits tight close-off without excessive motor strain.
• Available brackets make linkages adaptable to many valve bodies.
• Models available with 80 lb, 160 lb, and 320 lb stem force.
• Reversible cams on the Q5001 allow field selection of normally open
or normally closed valve operation.
• All models have anti-spin.
Home
Controls
Q5001 Valve Linkage for Modutrol IV Motors
Q5001 Parts
Stroke
Description
Used With
220828AA
—
Valve bracket assembly, Q5001
Q5001
220845/0767
—
Retainer button for Q5001
—
220848A
1/2 in.
Q5001 Cam
Q5001
220852A
—
Indicator, Q5001
Q5001
220858A
9/16 in.
9/16 inch lift Q5001 linkage cam assembly
Q5001
220861A
3/4 in.
3/4 inch lift Q5001 linkage cam assembly
Q5001
1 in.
1 inch lift Q5001 linkage cam assembly
Q5001
1 1/8 in.
1 1/8 inch lift Q5001 linkage cam assembly
Q5001
220865A
1 1/4 in.
1 1/4 inch lift Q5001 linkage cam assembly
Q5001
220867A
1 1/2 in.
1 1/2 inch lift Q5001 linkage cam assembly
Q5001
220874/0767
—
9/16 inch anti spin clip for Q5001
—
4074ETB
—
Antispin Kit, Q5001
Q5001
451
Industrial Combustion
Controls
70-6910
Pneumatic Controls
220863A
220864A
Commercial
Components
Product Number
Building Automation
Linkage Type: Valve
Damper and Valve Linkages
Q5020 Globe Valve Linkages
The Q5020 Globe Valve Linkages connect a Honeywell direct
coupled actuator (DCA) to a steam or water globe valve. The Q5020
Linkages are compatible with two-way and three-way globe valves.
• Used with two-way and three-way globe valves in modulating or twoposition service.
• Used with 25, 50, and 142 lb-in. spring return and 35, 70, 150, and
300 lb-in. non-spring return DCA.
• Quick and simple installation with no disassembly required.
• Heavy-duty Steel rack and pinion construction and Aluminum Diecast housing.
• Maintenance-free construction.
• Precision roller-bearing rack construction prevents premature valve
packing wear and leakage.
• Flexible actuator mounting orientation.
• Adjustable manual override lever and valve position indicator.
• Can be mounted on specific non-Honeywell valves using a
32004629 Bonnet Adapter Kit.
Linkage Type: Valve
Used with Actuator: Direct Coupled Actuator
Product Number
Bonnet
Size (in.)
Shaft
Dimensions
Stroke
Description
Q5020A1003
1 3/8 in.
1/2 in.
3/4 in.
Globe Valve Linkage with 1/2 inch shaft 1/2 in. diameter drive shaft
V5011G; V5011F;
V5013N; V5011N
Q5020B1001
1 3/8 in.
1 in.
3/4 in.
Globe Valve Linkage with 1 inch shaft
1 in. diameter drive shaft
V5011G; V5011F;
V5013N; V5011N
1 in. diameter drive shaft
V5051
Includes
Q5020C1009
1 3/8 in.
1 in.
1 1/2 in.
Globe Valve Linkage with 1 inch shaft
Q5020D1007
1 3/8 in.
1/2 in.
1/2 in.
Globe Valve Linkage with 1/2 inch shaft 1/2 in. diameter drive shaft
* TRADELINE models • SUPER TRADELINE models
452
customer.honeywell.com
70-6910
Used With
Siebe valves;
Johnson valves;
Siemms valves