Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Data Residence Hall Windows NT 4 Setup Compiled by Academic Computing Services 1997 Note: You will need to fill out a maintenance request (located in the repair request drop box at or near the front desk in each residence hall) to have the data port in your room turned on (activated) before attempting this setup. Should you have any trouble please contact your residence hall’s student data connection advisor(s). To install Remote Access Services (RAS) Steps: 1 2 3 4 Click on Start Go to Settings Select Control Panel Double click on the Network icon If the following window appears, click Yes If it doesn’t, skip to ‘To configure RAS’ 5 6 Uncheck Wired to the network:, by clicking in the check box Check Remote Access to the network:, clicking in the check box 7 8 9 10 11 Click on Next > Click on Next > (again) in the Network Adapters: window Verify the TCP/IP Protocol is selected in the next window, then click on Next > Click on Next > (again) in the Network Services: window Click on Next > (again) Windows NT4 Page 2 12 Insert the drive letter of your Windows NT Disk(s) 13 Click on Continue 14 Click on No 15 In the Remote Access Setup window, click on Add Windows NT4 Page 3 Installing a New Modem 1 2 In the Add RAS Device window, click on Install Modem Click on the Don’t detect my modem... check box 3 4 5 6 7 Click on Next > Click on Have disk… Insert the drive letter of your setup disk Click on OK Select Direct Connection (nt4_08.bmp) 8 9 Click on Next > Select COM1 in the ports box Windows NT4 Page 4 10 11 12 13 14 Click on Next > If no modem has been previously installed, enter 704 in the Area Code box, then click on Next > Click on Finish Back in the Add RAS Device window, click on OK Back in the Remote Access Setup window, click on Continue (At this point, the setup will read many files from your NT Disk(s).) 15 16 17 18 19 Click on Next > Click on Next > (again) to start the network Click on Next > (again) to make your computer a member of WORKGROUP Click on Finish In the Network Settings Change window, click on Yes to restart your computer To configure Remote Access Services (RAS) Steps: 1 2 3 4 5 6 Click on Start Go to Settings Select Control Panel Double click on the Network icon Click on the Services tab Select Remote Access Service Windows NT4 Page 5 7 Click on Properties… If there is a Dial-Up Networking Serial Cable as a device in the Remote Access Setup window: (like above) continue, otherwise go back to step 15 in the first section of this manual (install RAS) 8 9 10 11 12 13 Click on Continue Click on the Protocols tab Select TCP/IP Protocol Click on Properties Click on the DNS tab In the host box enter your user ID Windows NT4 Page 6 14 In the Domain box enter appstate.edu 15 In the DNS Server Search Order box enter 152.10.1.15 - Click on Add enter 152.10.1.5 - Click on Add enter 152.10.1.1 - Click on Add 16 In the Domain Suffix Search Order box enter appstate.edu Click on Add 17 Click on OK 18 Click on OK in the Network window 19 Close the Control Panels window To create a Dial-Up Networking Connection Steps: 1 Double click on My Computer on the desktop 2 Double click on Dial-Up Networking If your phonebook is empty follow the following steps. Otherwise click New. 3 4 Click on OK In the ‘Name the new phonebook entry:’ box enter: ASU Windows NT4 Page 7 5 6 Click on Next > In the Server window check the ‘Non-windows NT server …’ check box 7 8 9 10 11 12 13 Click on Next > Click on Next > (again) in the Phone Number window Verify the Point-to-Point Protocol (PPP) is selected Click on Next > in the Serial Line Protocol window Click on Next > in the Login Script window Click on Next > in the IP Address window In the DNS server: bow enter: 152.10.1.15 Windows NT4 Page 8 14 15 16 17 18 19 20 21 22 23 24 25 26 27 27 Click on Next > Click on Finish Click on More… Choose Edit entry and modem properties Click on the Basic tab Click Configure… Change Initial Speed (bps) to 57600 Click on OK Click on the Server tab make sure tcp/ip is checked and others unchecked Click on the Script tab Click on Before Dialing… Select the ‘Pop up a terminal window’ radio button Click on OK Click on OK (again) in the Edit Phone Entry window Starting your ASU Connection Steps: 1 2 Double click on My Computer on the desktop Double click on Dial-Up Networking Windows NT4 Page 9 3 4 5 Click on Dial Hit enter until you see an annex: prompt At the annex prompt type ppp and hit enter 6 If you see non-sense characters after you hit enter (as in the image above) click on Continue. You may now run WS_FTP, install and run Ewan, and other internet programs. There is no time limit on this connection. You may disconnect and reconnect at will. Windows NT4 Page 10