Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Fire Alarm Systems | D7025 Alarm and Trouble Relay Module D7025 Alarm and Trouble Relay Module ▶ Two Form C relays (alarm and trouble) ▶ 12 VDC or 24 VDC operation ▶ Easy installation onto the control panel ▶ No additional programming required after installation The D7025 Alarm and Trouble Relay Module is a plug-in device compatible with the D7022 Two-zone Fire Alarm Control Panel (FACP). It allows the D7022 to support two auxiliary Form C relays for connection to external devices such as the D185 Reversing Relay Module, the D2071A Digital Alarm Communicator Transmitter (DACT), or the D9068 DACT. The module provides one alarm relay and one trouble relay. Certifications and Approvals Region Certification USA UL UOJZ: Control Units, System (UL864, 9th edition), UTOU: Control Units and Accessories - Household System Type (UL985) CSFM 7167-1615: 162 and 7165-1615: 163 July 2008 Functions Relays The two Form C relays can be wired as either normallyclosed or normally-open. The alarm relay is used for external devices that must operate when the control panel is in alarm. The trouble relay is used for external devices that must operate when the control panel indicates a trouble condition. The FACP holds the trouble relay energized in normal standby. The C and NC terminals are connected in normal standby. Loss of AC power does not activate the trouble relay until the programmed AC fail timer expires. Installation/Configuration Notes Compatibility Information Category Product ID Product Description Control Panels D7022 Two-zone FACP Communication D2071A DACT Devices D2071AC DACT with wired transformer D2071ACT DACT with plug-in transformer D9068 DACT D132B Smoke detector reversing relay module D185 Reversing polarity module D7014 Class A zone converter module D7015 Class A NAC converter module D7025 Relay module Modules www.boschsecurity.com 2 | D7025 Alarm and Trouble Relay Module Mounting Considerations The D7025 mounts to the D7022 control panel with four nylon stand-offs that are supplied with the D7025. Note AC and battery power must be removed from the D7022 before installing the D7025. Wiring Considerations D7025 to FACP The connector pins from the eight-pin connector on the FACP board insert into the connector on the D7025. Connect the yellow and green earth-ground wire to the ground terminal on the FACP terminal strip. Parts Included Quant. Component 1 Relay module 1 Hardware pack 1 Literature pack Technical Specifications Outputs Active Current (both relays on): 60 mA Relay Contact Current (maximum): 5 A at 30 VDC or 120 VAC (resistive) Power Requirements Current (standby): 30 mA Voltage (operating): 12 VDC nominal or 24 VDC nominal supplied by FACP Ordering Information D7025 Alarm and Trouble Relay Module Provides one alarm relay and one trouble relay Americas: Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, New York, 14450, USA Phone: +1 800 289 0096 Fax: +1 585 223 9180 [email protected] www.boschsecurity.us D7025 Europe, Middle East, Africa: Bosch Security Systems B.V. P.O. Box 80002 5600 JB Eindhoven, The Netherlands Phone: + 31 40 2577 284 Fax: +31 40 2577 330 [email protected] www.boschsecurity.com © Bosch Security Systems Inc. 2010 | Data subject to change without notice T1372047499 | Cur: en-US, V5, 4 Jul 2010 Asia-Pacific: Represented by Robert Bosch (SEA) Pte Ltd, Security Systems 11 Bishan Street 21 Singapore 573943 Phone: +65 6258 5511 Fax: +65 6571 2698 [email protected] www.boschsecurity.com