Download Instrumentation Mechanician

Instrumentation Mechanician
Trade Test Centre Accreditation Checklist
Accrediting ETQA
e.g. QCTO or SETA Name
TTC Name:
Centre Manager Name
TTC Contact Details
TTC Physical Address
e.g. 17 Tonga-tinge Street, Mable Hall, 1612
Assessor/Lecturer Name
Assessor qualification
relevant to the trade
SME Name
SME Employer Details
SME Employer contact
Ratio of candidates to
Assessor
e.g. 12 Candidates:1 Facilitator
No. of Candidates per
given time in the Venue
Accreditation History (If previously accredited through the SETA System, Complete the section below )
Accredited by:
SETA Name
Accreditation Visit Date:
Accreditation No.
DD/MM/CCYY
Province
OFO Code (if applicable)
e.g. Northern Cape
Municipality
e.g. Madibeng
New Accreditation Information
Trade Test
X
OFO Code
Accreditation Date
Urban
X
Rural
X
Page 1 of 8
DD/MM/YYYY
Instrumentation Mechanician
Item Description
Ratio Y N
Hand Tools
Circuit board stand
1:1
Soldering station
1:1
Set screw drivers flat
1:1
Set screw drivers Philips
1:1
Set Allen keys 1.5mm – 10mm
1:1
Crimping tool ratchet type insulated
1:1
Engineer’s square 100mm
1:1
Padlock and key
1:1
Pliers – combination insulated 200mm
1:1
Pliers – diagonal cutting 200mm
1:1
Pliers – gas non-insulated 200mm
1:1
Pliers – long nose insulated 200mm
1:1
Pliers – round nose insulated 150mm
1:1
Set Flat screw drivers 6 piece
1:1
Set Phillips screw drivers 6 piece
1:1
Set spanners tube 0BA – 10BA
1:1
Set spanners: 6-22 (flat ring)
1:1
Shifting spanner/ Adjustable wrenches
1:1
Tape –steel 5m
1:1
Retractable knife
1:1
5 Tier Toolbox
1:1
Vice grip 250mm
1:3
Wire stripper spring assisted insulated
1:1
Bastard file 300mm plus file handle
1:1
Second cut 300mm plus file handle
1:1
Smooth file 300mm plus file handle
1:1
Round file 400mm plus file handle
1:1
Comments:
Page 2 of 8
Acceptable/Not
Acceptable
Instrumentation Mechanician
Item Description
Ratio Y N
Special Tools
Power supply (3V, 6V, 9V, 12V and 24V)
1:1
Function generator
1:1
Oscilloscope
1:1
Comments:
Measuring Equipment
Digital Multimeter
1:1
Spirit Level
1:1
Comments:
Page 3 of 8
Acceptable/Not
Acceptable
Instrumentation Mechanician
Item Description
Ratio Y N
Machinery
Pneumatic simulator with the capability of doing
flow, hydrostatic level and purge type level control.
Must have sensor, controller and valve minimum.
 Loop drawings for each loop (must be
available if required)
Pneumatic dP cell (may be separate from
simulator)
Pneumatic control valve
(may be separate from simulator)
Tools and manuals to calibrate dP cell

Pneumatic calibrator (manometer, etc.)

1:1
1:1
1:1
1:1
1:1
1:1
Conversion table/ Symbol sheet (ISO
3511/1/2/3)
Copper tubing, fittings, nuts and ferrules
1:1
Flexible tubing
1:1
Pipe bender
1:1
Pipe cutter
1:1
Pre-bent tubing for simulator (must be available if
required)
Electronic simulator with the capability of doing
flow, level, and cascade type level control. Must
have flow and level transmitters, pressure switch, 2
X controllers, PLC, trips and alarms and valve
minimum
Electronic transmitter (may be separate from
simulator)
Flow sensor/ transmitter (may be separate from
simulator)
Pressure switch (may be separate from simulator)
1:1
Tools, manuals, programmer (if applicable) and
equipment to calibrate, fault find or configure
electronic equipment)
Conversion table/ Symbol sheet (ISO 3511/1/2/3)
1:1
Loop drawings for each loop (must be available if
required)
Pneumatic calibrator (manometer, etc.)
1:1
PC to program PLC
1:1
Configuration and data sheets for all equipment
used in the application.
Selection of RTD’s and Thermocouples
1:1
Data Sheets for RTD’s and Thermocouples
1:1
Temperature measuring device (Controller and
Indicator)
1:1
Page 4 of 8
1:1
1:1
1:1
1:1
1:1
1:1
1:1
1:1
Acceptable/Not
Acceptable
Instrumentation Mechanician
Item Description
Ratio Y N
Analogue Multimeter
1:1
Millivolt source
1:1
Heat source (Urn, Kettle, Oven, etc.)
1:1
Compensating Leads
1:1
Comments:
Equipments (Long Term Consumables)
Soldering Iron
1:1
Solder sucker
1:1
Soldering Iron station
1:1
Comments:
Consumables
Electronic components
1:1
Vero board (50mm X 50mm)
1:1
Solder
1:1
Wire (Red and Black)
1:1
Resistors
1:1
Transistors
1:1
Capacitors
1:1
Diodes
1:1
Page 5 of 8
Acceptable/Not
Acceptable
Instrumentation Mechanician
Item Description
Ratio Y N
Insulation tape
1:1
Red wire
1:1
Black wire
1:1
Mystery Box
1:1
T – Pieces
1:1
Crocodile clamps (wire)
1:1
Banana clamps (wire)
1:1
Comments:
Safety
Safety boots (Pair)
1:1
Personal Protective Clothing (Suit)
1:1
Safety glasses
1:1
Comments:
Page 6 of 8
Acceptable/Not
Acceptable
Instrumentation Mechanician
Item Description
Ratio Y N
Logistics And Lay-Out
Cubicles proportional to the number of candidates
tested
Panel proportional to the number of candidates tested
Class rooms for theoretical training
Workshops for practical training
Teaching media including:

Projectors

White boards

Stationery

Models samples

Green boards/ Notice Boards
Demarcations
Comments:
Page 7 of 8
Acceptable/Not
Acceptable
Instrumentation Mechanician
I ……………………………………… the undersigned, hereby declare that all the
tools/equipment/trade test materials/machines which were checked are the sole
property of the TTC.
Accreditation recommended
Yes
No
Constraints/Gaps:
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_________________
Recommendations:
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_________________
SME Name
Signature
Date: DD/MM/CCYY
Organizational Rep. Name
Designation
Signature
Date DD/MM/CCYY
Page 8 of 8