* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Design Document v0.9 - WordPress@UP
Resistive opto-isolator wikipedia , lookup
Mains electricity wikipedia , lookup
Sound reinforcement system wikipedia , lookup
Phone connector (audio) wikipedia , lookup
Alternating current wikipedia , lookup
Spectral density wikipedia , lookup
Electrical engineering wikipedia , lookup
Audio power wikipedia , lookup
Transmission line loudspeaker wikipedia , lookup
Public address system wikipedia , lookup
Pulse-width modulation wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Audio crossover wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Rectiverter wikipedia , lookup
Dynamic range compression wikipedia , lookup
Electronic engineering wikipedia , lookup
University of Portland School of Engineering 5000 N. Willamette Blvd. Portland, OR 97203-5798 Design Document Frequency Response Audio Visualizer Team Members: Jake Nylund (Fall Team Lead) Kevin Ratuiste (Spring Team Lead) Alex Arlint (Treasurer) Robert Rodriguez (Secretary) Industry Representatives: John Turner – Impinj, Inc. Faculty Advisors: Dr. Joseph Hoffbeck Clients: Will Taylor – Student Phone 503 943 7314 Fax 503 943 7316 DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 2 REVISION HISTORY Rev. Date Author 0.9 1 Nov 2013 Team UNIVERSITY OF PORTLAND Reason For Changes First draft submitted to advisor SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 3 TABLE OF CONTENTS REVISION HISTORY .........................................................................................................................................................2 INTRODUCTION .............................................................................................................................................................4 Figure 1: Front, Top, and Rear View Concept Sketch ............................................................................................5 HIGH LEVEL ARCHITECTURE ...........................................................................................................................................6 Figure 2: High Level Schematic .............................................................................................................................6 COMPONENT STRUCTURE .............................................................................................................................................7 User Interface ............................................................................................................................................................7 Figure 3: User Interface Component Diagram ......................................................................................................7 Arduino Due Microcontroller ....................................................................................................................................8 Figure 4: Arduino Due Layout ...............................................................................................................................8 Software Component ................................................................................................................................................9 Figure 5: General Signal Process ...........................................................................................................................9 Figure 6: FFT Sample Code ..................................................................................................................................10 Signal Amplification .................................................................................................................................................11 Figure 7: LM386 Audio Amp Pinout and External Components .........................................................................11 Electromagnet .........................................................................................................................................................12 Figure 8: Electromagnet Control Circuit .............................................................................................................12 Mechanical Components.........................................................................................................................................12 SYSTEM TEST PLAN ......................................................................................................................................................13 Microcontroller .......................................................................................................................................................13 Electromagnet/Ferro Fluid Display..........................................................................................................................13 Figure 9: Electromagnet Test Switch ..................................................................................................................13 DEVELOPMENT PLAN, MILESTONES, ASSUMPTIONS, RISKS, AND FACILITIES .............................................................15 Development Plan ...................................................................................................................................................15 Figure 10: Overall Design Process Diagram ........................................................................................................15 Milestones ...............................................................................................................................................................17 Assumptions ............................................................................................................................................................17 Risks .........................................................................................................................................................................17 Facilities ...................................................................................................................................................................18 FINAL BUDGET .............................................................................................................................................................18 CONCLUSION ...............................................................................................................................................................18 REFERENCES.................................................................................................................................................................19 UNIVERSITY OF PORTLAND SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 4 INTRODUCTION The overall goal of this device is to visualize the frequency response of an audio signal. The input will be an analog line level audio signal connected via a standard 3.5mm headphone jack. This signal will enter the microcontroller where it will be processed and filtered to separate the various frequencies in the audio signal. Implementing the filters digitally allows more flexibility in how the microprocessor will process the signal as well as the resulting action or response. Once the frequencies of the audio signal are separated, they will be output to the electromagnets, which, in turn, will manipulate the ferromagnetic fluid creating a visual representation of the audio signal. Below is a comprehensive list of the anticipated design challenges the project could face as well as how the challenges could be overcome: Challenge 1: It could be difficult to find a power supply that produces enough for each electromagnet and then also have the microcontroller coordinate where the current goes. If a single, suitable power supply cannot be found, then it would also be possible to use smaller, separate power supplies that would each be easier to control and locate individually. Challenge 2: There is a possibility that the synthesized ferrofluid reacts differently or more inconsistently than expected. In this situation, it would be best to simply buy ferrofluid from a chemical supplier so that the team’s focus is not on the chemistry of ferrofluid; the main focus should be on the hardware/software design and construction of the visualizer. Challenge 3: The team may run into issues constructing certain hardware components, such as the Plexiglas containers for the ferrofluid or the electromagnets themselves. In such a situation, there are multiple resources available, including the faculty at the University of Portland, the design project technicians, or at worst, the library and online sources to help direct the team in the right direction. Our final result should resemble the concept sketch provided in Figure 1, below. The rest of this document lays out the detailed design choices Team Couch Street has decided upon. Within each section, there will be some recurring words that the team assumes the reader understands. For example, it is assumed that the reader knows that Arduino is an open-source electronic prototyping platform; the Arduino Due is the microcontroller that the team will be using for the project. The team also assumes that the reader knows what an LED, IC, and electromagnet are; these electronic components will be utilized in the construction of the Frequency Beats project. The following sections of this document will include which specific tools and technologies the team will utilize in the production of the project as well as detailed descriptions of how the project will physically be laid out, how the project will be wired, and UNIVERSITY OF PORTLAND SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 5 how each component will interact with the other components. Each section is broken down as follows: 1. High-level Architecture 2. Component Structure 3. System Test Plan 4. Development Plan, Milestones, Assumptions, and, Risks 5. Final Budget 6. Conclusion 7. References 8. Appendices Figure 1: Front, Top, and Rear View Concept Sketch UNIVERSITY OF PORTLAND SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 6 HIGH LEVEL ARCHITECTURE Figure 2 below shows the high level architecture of FreqBeats. The key component of this project is the Arduino Due, which takes the audio signal at its input, digitally filters it, and outputs three different frequencies. The three frequencies are low-range, mid-range, and highrange. Each frequency is amplified by its own LM386 and then used to trigger a TIP36C power transistor. The power transistor, when triggered allows current to flow through the electromagnet, thus manipulating the ferrofluid. FreqBeat utilizes two power supplies, a 16V for the electromagnets and a 3.3V to power the Arduino. 16V Power Supply 3.3V Power Supply Electromagnet (Low-Range) LM386 Audio Amp Electromagnet (Mid-Range) Electromagnet (High-Range) TIP36C Power Transistor Low-Range Out Audio Signal In Arduino Due Mid-Range Out High-Range Out LM386 Audio Amp TIP36C Power Transistor LM386 Audio Amp TIP36C Power Transistor Figure 2: High Level Schematic UNIVERSITY OF PORTLAND SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 7 COMPONENT STRUCTURE User Interface The user will plug in their audio signal via a 3.5mm standard line level audio cable on the back side of the project device. Once connected, the user presses play and watches the audio visualization of his or her music choice on the front side of the device. Alternatively, the user may press one of the three buttons present on the front of the device to activate the respective electromagnet in order to manipulate the ferromagnetic fluid without audio. The following figure shows the three buttons and audio cable that the user will be able to interact with. Figure 3: User Interface Component Diagram UNIVERSITY OF PORTLAND SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 8 Arduino Due Microcontroller The primary digital component that will be utilized in our design is the Arduino Due, which is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU. It is the first Arduino bard based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins, 12 analog inputs, 4 UARTs, an 84 MHz clock, a USB OTG capable connection, 2 DAC, 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button. This component will be used to digitally filter the input audio file, separating it into lowrange, mid-range, and high-range, then output those 3 signals to individual audio amplifiers. Figure 4: Arduino Due Layout UNIVERSITY OF PORTLAND SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 9 Software Component Figure 5: General Signal Process Figure 5 shows the general process that the signal will undergo as it is sampled by the Arduino. Simply stated the Arduino will continually sample the input on one of the Digital Input pins using a Loop. From there using Fast Fourier Transform (FFT) the signal will be separated as Low pass, Band pass, and High pass filters. Each signal will be output to three different digital output pins. init() Initialize I/O pins to being the sampling and output process pinMode(2, INPUT); // Set Due pin 2 (Digital Pin 2) to be an INPUT pin pinMode(22, OUTPUT); // Set Due pin 22 ( Digital Pin 22) to be an OUTPUT pin) sampleLoop() This loop will continually sample the audio input in Analog format. Using FFT it will split the signal and output onto three separate pins for High, Low , and Band pass frequencies. UNIVERSITY OF PORTLAND SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 10 inputAudio = analogRead(2); // get input from pin 2 Figure 6: FFT Sample Code http://www.drdobbs.com/cpp/a-simple-and-efficient-fft-implementatio/199500857 Send each split signal continually to their respective pins, for example pins 22, 23, 24. delay() In order to achieve real time audio output that produces a response in the ferromagnetic fluid in time with the music there will need to be a precisely tuned delay. The specific delay will be modified to produce the best time output. UNIVERSITY OF PORTLAND SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 11 Signal Amplification After the audio signal is broken up into three separate low-range, mid-range, and highrange frequencies, it needs to be amplified. This is done with an LM386 audio amplifier which can provide a gain between 20 to 200. Shown in Figure 7 is the pinout of the LM386 and the external components that will be connected. Note that varying the values of the resistor and capacitor connected between pin 1 and pin 8 provides gain control and the ability to select any gain value between 20 and 200. Vs 6 2 1 8 5 LM386 250F To TIP36C Power Transistor Out From Arduino In 10Ω 3 4 Bypass 0.05F Figure 7: LM386 Audio Amp Pinout and External Components UNIVERSITY OF PORTLAND SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 12 Electromagnet Power Supply Even with an audio amplifier, the signal from the Arduino is not strong enough to drive the electromagnet. Thus, the electromagnets will be powered by a 16V power supply. Control The signal from the Arduino will determine when the electromagnet is on and off. A TIP36C power transistor, which acts as the “on/off” switch for the electromagnet, will be controlled by the signal from the Arduino. Current from the 16V power supply is able to flow through the electromagnet when there is an observable voltage seen at the base of the power transistor, thus turning the electromagnet on. 16V Electromagnet From LM386 Power Amplifier 2 1 TIP36C 3 Figure 8: Electromagnet Control Circuit Build The electromagnet will be comprised of 16 gauge magnet wire. It will be wrapped around a 1/2” diameter metal core that is 5 inches in length. The electromagnet will be mounted above the ferrofluid display. Mechanical Components Our project will incorporate several simple mechanical devices. One of which will be the casing that houses the Ferro fluid. For this, we plan to use a glass cylinder with a diameter of approximately 2 inches and height of 5 inches. The electromagnetic will be hard mounted above the cylinder. Additionally, we will construct a wood base to mount the three Ferro-fluid displays to as well as the Arduino and support circuitry. The base will be approximately 18 inches long and 6 inches wide. UNIVERSITY OF PORTLAND SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 13 SYSTEM TEST PLAN Microcontroller In order to adequately test the Arduino Due microcontroller to verify that the digital filters are functioning as desired, the following steps will be executed: 1.) Set up a breadboard with 3 different LEDs, one for indicating low frequencies (20Hz – 400Hz), one for mid-range frequencies (400Hz – 5.2KHz), and one for high frequencies (5.2KHz – 20KHz). 2.) Manufacture a test signal comprised of 5 seconds of low frequency data (20Hz – 400Hz), 5 seconds of mid-range frequency data (400Hz – 5.2KHz), and 5 seconds of high frequency data (5.2KHz – 20 KHz). 3.) Use the manufactured signal as an input to the Arduino. 4.) If the LEDs corresponding to the expected frequencies at time X light up, then the Arduino is functioning properly. 5.) Otherwise, re-examine the Arduino code for potential errors and then redo the steps above until the desired result is achieved. Electromagnet/Ferro Fluid Display Testing of the electromagnets on each of the three displays will be done as follows: 1.) Construct a simple switch for each of the three displays that allows current to flow from the power supply, through the electromagnet, and then to ground, as seen in the diagram below: Figure 9: Electromagnet Test Switch UNIVERSITY OF PORTLAND SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 14 2.) When the switch is in position 1, the electromagnet is connected to the Arduino. 3.) When the switch is in position 2, there is no current flowing through the electromagnet and it is off. 4.) When the switch is in position 3, current flows from the power supply, through the electromagnet, and to ground. This is the test position to simply show that the electromagnet is working. 5.) If the electromagnet does not work when the switch is in position 1 or 3 check the following: a. Is the power supply on and working correctly? b. Are there any shorts in the system? c. Check each individual component for failures. UNIVERSITY OF PORTLAND SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 15 DEVELOPMENT PLAN, MILESTONES, ASSUMPTIONS, RISKS, AND FACILITIES Development Plan Figure 10: Overall Design Process Diagram UNIVERSITY OF PORTLAND SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 16 Project Proposal Team Couch Street developed the idea for a ferrofluid audio visualizer by combining two different project ideas; one to work with ferrofluid, and the other to work with software to digital process audio input. The appeal of this project is the combination of skills required to successfully design and build a prototype. Function Requirements This is the document that details the conceptual design of the ferrofluid visualizer. This includes primarily the goals, conceptual sketches, and plan for production. Design Document See Recursion. Testing Ferrofluid and Electromagnets In order to determine the specific calculations for voltage and current requirements, the team tested multiple electromagnets and ferrofluid with different viscosities. These tests lead to changes and finalized decisions in the Design Document. Software Development To meet the required deadline, team members Robert Rodriguez and Jake Nylund will being the software aspect of the project over Christmas break. To best get a handle on the language and chip architecture it is necessary to start as early as possible. Construct Housing for Ferrofluid and Base As discussed in the Assumptions portion of this document, the team assumes we will have the assistance of Alan Hansen in the construction of our ferrofluid containers and base for our prototype. This will be constructed of Plexiglas and plywood respectively. Construct Electromagnets This has its own section as the construction of an efficient and powerful electromagnet takes significant time and focus, and the team requires three of them. Test FFT with Board and LED’s After finishing the software development stage, it will be necessary to test the Fast Fourier Transform (FFT) algorithm to ensure that it properly splits the signals into High, Band, and Low pass frequencies. The team will use LED’s and specific High frequencies, Midband, and Low frequencies individual to test the Arduino’s DSP program. Test OP Amp Configuration Team members Alex Arlint and Kevin Ratuiste will test the Op amps construction in the Shiley lab to ensure the expected voltage increase. Assemble and Test First Ferrofluid Display UNIVERSITY OF PORTLAND SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 17 At this point in the design process everything should be ready to assemble into one unit. The Arduino will pass a signal through the OP Amp which, with the increase in voltage, will power the Electromagnet, which will in turn cause the ferrofluid to respond in time to the audio signal. Test Second and Third Ferrofluid Displays With one fully functional Ferrofluid Display the team anticipates a much quicker turnaround time in production of the second and third ferrofluid displays. The bugs should be fewer and worked out faster. Test and Debug By this point everything will be assembled. Final Testing stages will ensure that all portions of the visualizer are working together as expected. Founder’s Day Presentation The team will present the project to faculty and students at the University of Portland. Milestones The milestones for the project have been stated previously in the Functional Specifications Document. Please refer to that as there have been no changes in the milestones. Documentation can be found at: http://wordpress.up.edu/egr13couchstreet/visualizer-status/ Assumptions There are several assumptions that the team is making about the construction phase of the project. Alan Hansen will be available to help with the construction of the base and container for the ferrofluid The Arduino Due will function as stated in the specifications sheet listed on the Arduino website. All hardware will be available and function properly Some hardware components, such as those necessary in the construction of the OP Amp circuit, will be available from the University and not necessary to purchase. Risks The risks for the project have been stated previously in the Functional Specifications Document. Please refer to that as there have been no changes in the risks. Documentation can be found at: http://wordpress.up.edu/egr13couchstreet/visualizer-status/ UNIVERSITY OF PORTLAND SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 18 Facilities Throughout the experimentation, design, and construction process of our project will make use of the bench space and equipment in Shiley 306. As far as software requirements, there are open source microcontroller environments and/or MATLAB on any Engineering build computer. The equipment used will likely be limited to a soldering iron, ICs, and various hand tools for construction. FINAL BUDGET Material 2-1/4" OD x 2" ID x 36” Plexiglass tube 2.5” Plexiglass disk Arduino Due ½” x 6” metal core 250ml ferrofluid 3.5mm female adapter LM386 TIP36C 16V power supply 3.3V power supply Display base parts (Plywood) Magnet wire 16AWG spool (500’ each) Price 12.50 Quantity 1 Total Cost 12.50 12.50 40.00 10 58.25 5 0.94 1.89 < 50.00 <25.00 20.00 20.00 1 1 3 1 1 3 3 1 1 1 2 12.50 40.00 30.00 58.25 5 2.82 5.67 <50.00 <25.00 20.00 40.00 TOTAL 301.74 CONCLUSION The ferromagnetic fluid audio visualizer is a different way of seeing different frequencies used in different types of music. It will show the low, middle and high frequencies ranges by processing the sound form a standard 3.5mm headphone jack, used by almost all music players and splitting the signal accordingly. In order to succeed on this project the team will need to continuously work to stay on schedule. The schedule that we have laid out is reasonable so long as time is used efficiently. The real key is to effective testing and debugging. In terms of software it is important to ensure the signal is processed correctly and then output to the proper pin. For hardware the key part is the construction of the OP Amp circuit and Electromagnet. Teamwork will keep the project on track. UNIVERSITY OF PORTLAND SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND DESIGN DOCUMENT TEAM COUCH STREET REV. 0.9 PAGE 19 REFERENCES http://elm-chan.org/works/akilcd/report_e.html - audio specturm monitor http://forum.arduino.cc/index.php/topic,37689.0.html http://playground.arduino.cc/Main/ArduinoSynth http://arduino.cc/en/Main/arduinoBoardDue https://www.youtube.com/watch?v=a_flWeIdoBg http://abhishekjainnsit.blogspot.com/2012/10/digital-filters-on-arduino.html - Digital Filters http://forum.arduino.cc/index.php?topic=42510.0 – Arduino Digital Filter http://www.paulodowd.com/2013/06/arduino-38khz-bandpass-software-digital.html - 38kHz Ban Pass Filter http://forum.arduino.cc/index.php/topic,42635.0.html – Low Pass Filter Design http://www.drdobbs.com/cpp/a-simple-and-efficient-fft-implementatio/199500857 - FFT UNIVERSITY OF PORTLAND SCHOOL OF ENGINEERING CONTACT: JAKE NYLUND