Download Dual Differential Line Driver With 3-State Outputs

SN75159
DUAL DIFFERENTIAL LINE DRIVER
WITH 3-STATE OUTPUTS
SLLS088B – JANUARY 1977 – REVISED MAY 1995
D
D
D
D
D
D
D
D
D
Meets or Exceeds the Requirements of
ANSI EIA/TIA-422-B and ITU
Recommendation V.11
Single 5-V Supply
Balanced Line Operation
TTL Compatible
High-Impedance Output State for
Party-Line Applications
High-Current Active-Pullup Outputs
Short-Circuit Protection
Dual Channels
Clamp Diodes at Inputs
D OR N PACKAGE
(TOP VIEW)
NC
1Z
1Y
1A
1B
1EN
GND
1
14
2
13
3
12
4
11
5
10
6
9
7
8
VCC
2Z
2Y
2B
2A
2EN
NC
NC – No internal connection
description
The SN75159 dual differential line driver with 3-state outputs is designed to provide all the features of the
SN75158 line driver with the added feature of driver output controls. There is an individual control for each driver.
When the output control is low, the associated outputs are in a high-impedance state and the outputs can neither
drive nor load the bus. This permits many devices to be connected together on the same transmission line for
party-line applications.
The SN75159 is characterized for operation from 0°C to 70°C.
logic symbol†
logic diagram (positive logic)
&
1EN 6
1A 4
EN
1EN
3
2
1B 5
2EN 9
12
2A 10
2B 11
13
6
1Y
1Z
1A
1B
4
5
3 1Y
2
1Z
2Y
2Z
2EN
† This symbol is in accordance with ANSI/IEEE Std 91-1984
and IEC Publication 617-12.
2A
2B
9
10
12
11
13
2Y
2Z
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  1995, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SN75159
DUAL DIFFERENTIAL LINE DRIVER
WITH 3-STATE OUTPUTS
SLLS088B – JANUARY 1977 – REVISED MAY 1995
schematic (each driver)
VCC
To Other
Driver
B A
5, 11
4, 10
14
V
V
4 kΩ
9Ω
Y
9Ω
2, 13
3, 12
V
EN
GND
4 kΩ
6, 9
7
V . . . VCC bus
Resistor values shown are nominal.
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
Z
SN75159
DUAL DIFFERENTIAL LINE DRIVER
WITH 3-STATE OUTPUTS
SLLS088B – JANUARY 1977 – REVISED MAY 1995
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Off-state voltage applied to open-collector outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 V
Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values except differential output voltage VOD are with respect to the network ground terminal. VOD is at the Y output with
respect to the Z output.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
D
950 mW
7.6 mW/°C
608 mW
N
1150 mW
9.2 mW/°C
736 mW
recommended operating conditions
Supply voltage, VCC
High-level input voltage, VIH
MIN
NOM
MAX
UNIT
4.75
5
5.25
V
2
Low-level input voltage, VIL
High-level output voltage, IOH
Low-level output current, IOL
Operating free-air temperature, TA
0
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
V
0.8
V
– 40
mA
40
mA
70
°C
3
SN75159
DUAL DIFFERENTIAL LINE DRIVER
WITH 3-STATE OUTPUTS
SLLS088B – JANUARY 1977 – REVISED MAY 1995
electrical characteristics over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VIK
Input clamp voltage
VCC = 4.75 V,
II = – 12 mA
VOH
High level output voltage
High-level
VCC = 4.75 V,,
VIH = 2 V,
VIL = 0.8 V,,
IOH = – 40 mA
VOL
Low level output voltage
Low-level
VCC = 4.75 V,,
VIH = 2 V,
VIL = 0.8 V,,
IOL = 40 mA
VOK
VO
Output clamp voltage
VCC = 5.25 V,
VCC = 4.75 V to 5.25 V,
IO = – 40 mA
IO = 0
|VOD1|
Differential output voltage
IO = 0
|VOD2|
Differential output voltage
VCC = 5.25 V,
VCC = 4.75 V
∆|VOD|
Change
g in magnitude
g
of
differential output voltage‡
VCC = 4
4.75
75 V
VOC
Common-mode output
voltage§
VCC = 5.25 V
VCC = 4.75 V
∆|VOC|
Change
g in magnitude
g
of
common-mode output voltage‡
VCC = 4
4.75
75 V to 5
5.25
25 V
IO
Output current with power off
VCC = 0
Output voltage
MIN
24
2.4
MAX
UNIT
– 0.9
–1.5
V
3
See Figure 1
VO = 6 V
VO = – 0.25 V
04
0.4
V
– 1.1
–1.5
V
6
V
3.5
2VOD2
V
3
II
Off-state
Off
t t (high-impedance
(hi h i
d
state) output
out ut current
Input current at maximum input
voltage
IIH
IIL
High-level input current
IOS
Short-circuit output current¶
ICC
Low-level input current
Supply current (both drivers)
VCC = 5.25
5 25 V,
V
Output
Out
ut controls at 0.8
08V
TA = 70°C
V
± 0.02
0 02
± 0.4
04
1.8
3
1.5
3
± 0.01
0 01
± 0.4
04
0.1
100
– 0.1
– 100
V
V
V
µA
± 100
VO = – 0.25 V to 6 V
TA = 25°C
VO = 0 to VCC
IOZ
V
0 25
0.25
0
2
RL = 100 Ω
Ω,
TYP†
± 10
VO = 0
VO = 0.4 V
– 20
VO = 2.4 V
VO = VCC
± 20
± 20
µA
20
VCC = 5
5.25
25 V
V,
VI = 5
5.5
5V
1
mA
VCC = 5.25 V,
VCC = 5.25 V,
VI = 2.4 V
VI = 0.4 V
40
µA
VCC = 5.25 V
VCC = 5.25 V,
TA = 25°C,
– 40
Inputs grounded,
g
No load
–1
– 1.6
mA
– 90
– 150
mA
47
65
mA
† All typical values are at VCC = 5 V and TA = 25°C except for VOC, for which VCC is as stated under test conditions.
‡ ∆|VOD| and ∆|VOC| are the changes in magnitudes of VOD and VOC, respectively, that occur when the input is changed from a high level to a low
level.
§ In ANSI Standard EIA/TIA-422-B, VOC, which is the average of the two output voltages with respect to GND, is called output offset voltage, VOS.
¶ Only one output should be shorted at a time, and duration of the short circuit should not exceed one second.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN75159
DUAL DIFFERENTIAL LINE DRIVER
WITH 3-STATE OUTPUTS
SLLS088B – JANUARY 1977 – REVISED MAY 1995
switching characteristics over operating free-air temperature range, VCC = 5 V
PARAMETER
TEST CONDITIONS
tPLH
tPHL
Propagation delay time, low-to-high-level output
tPLH
tPHL
Propagation delay time, low-to-high-level output
tTLH
tTHL
Transition time, low-to-high-level output
tPZH
tPZL
Output enable time to high level
tPHZ
tPLZ
Output disable time from high level
CL = 30 pF,, RL = 100 Ω,,
Termination A
Propagation delay time, high-to-low-level output
MIN
See Figure
2,,
g
CL = 15 pF,
pF See Figure 2,
2 Termination B
Propagation delay time, high-to-low-level output
TYP†
MAX
16
25
ns
UNIT
11
20
ns
13
20
ns
9
15
ns
4
20
ns
4
20
ns
CL = 30 pF,, RL = 100 Ω,,
Termination A
See Figure
g
2,,
CL = 30 pF, RL = 180 Ω,
CL = 30 pF, RL = 250 Ω,
See Figure 3
7
20
ns
See Figure 4
14
40
ns
See Figure 3
10
30
ns
Output disable time from low level
CL = 30 pF, RL = 180 Ω,
CL = 30 pF, RL = 250 Ω,
See Figure 4
17
35
ns
Overshoot factor
RL = 100 Ω, See Figure 2, Termination C
Transition time, high-to-low-level output
Output enable time to low level
10%
† All typical values are at TA = 25°C.
SYMBOL EQUIVALENTS
DATA-SHEET PARAMETER
EIA/TIA-422-B
VO
|VOD1|
Voa, Vob
Vo
|VOD2|
∆|VOD|
VOC
Vt
| |Vt| – |Vt| |
|Vos|
|Vos – Vos|
|Isa| , |Isb|
∆|VOC|
IOS
IO
|Ixa| , |Ixb|
PARAMETER MEASUREMENT INFORMATION
50 Ω
VOD2
50 Ω
VOC
Figure 1. Differential and Common-Mode Output Voltages
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SN75159
DUAL DIFFERENTIAL LINE DRIVER
WITH 3-STATE OUTPUTS
SLLS088B – JANUARY 1977 – REVISED MAY 1995
PARAMETER MEASUREMENT INFORMATION
1 kΩ
5V
Input
Y Output
Z Output
Pulse
Generator
(see Note A)
50 Ω
Y
Y
Z
CL= 30 pF
(see Note B)
Y
CL = 15 pF
(see Note B)
Z
RL = 100 Ω
CL= 15 pF
(see Note B)
RL = 100 Ω
Z
TERMINATION C
TERMINATION A
TERMINATION B
TEST CIRCUITS
25 ns
5 ns
90%
1.5 V
Input
5 ns
90%
1.5 V
10%
3V
90%
VOH
90%
1.5 V
10%
1.5 V
10%
tTLH
90%
tTHL
VOL
0%
tPLH
90%
1.5 V
10%
100%
tTHL
tPHL
Z Output
0V
tPHL
tPLH
Y Output
Overshoot
10%
1.5 V
10%
VOH
Overshoot
VOL
tTLH
VOLTAGE WAVEFORMS
NOTES: A. The pulse generator has the following characteristics: ZO = 50 Ω, PRR ≤ 10 MHz.
B. CL includes probe and jig capacitance.
Figure 2. Test Circuits, Voltage Waveforms, and Overshoot Factor
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN75159
DUAL DIFFERENTIAL LINE DRIVER
WITH 3-STATE OUTPUTS
SLLS088B – JANUARY 1977 – REVISED MAY 1995
PARAMETER MEASUREMENT INFORMATION
Input
Pulse
Generator
(see Note A)
50 Ω
CL= 30 pF
(see Note B)
Output
RL = 180 Ω
CL = 30 pF
(see Note B)
1 kΩ
5V
TEST CIRCUIT
≤ 5 ns
≤ 5 ns
90%
Input
1.5 V
10%
3V
90%
1.5 V
100 ns
10%
0V
tPZH
VOH
Output
1.5 V
0.5 V
tPHZ
Voff = 0
VOLTAGE WAVEFORMS
NOTES: A. The pulse generator has the following characteristics: ZO = 50 Ω, PRR ≤ 500 kHz.
B. CL includes probe and jig capacitance.
Figure 3. Test Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SN75159
DUAL DIFFERENTIAL LINE DRIVER
WITH 3-STATE OUTPUTS
SLLS088B – JANUARY 1977 – REVISED MAY 1995
PARAMETER MEASUREMENT INFORMATION
Input
Pulse
Generator
(see Note A)
5V
50 Ω
CL= 30 pF
(see Note B)
RL = 250 Ω
5V
Output
1 kΩ
CL= 30 pF
(see Note B)
TEST CIRCUIT
≤ 5 ns
90%
Input
1.5 V
10%
≤ 5 ns
3V
90%
1.5 V
100 ns
10%
tPZL
0V
tPLZ
5V
Output
1.5 V
0.5 V
VOL
VOLTAGE WAVEFORMS
NOTES: A. The pulse generator has the following characteristics: ZO = 50 Ω, PRR ≤ 500 kHz.
B. CL includes probe and jig capacitance.
Figure 4. Test Circuit and Voltage Waveform
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN75159
DUAL DIFFERENTIAL LINE DRIVER
WITH 3-STATE OUTPUTS
SLLS088B – JANUARY 1977 – REVISED MAY 1995
TYPICAL CHARACTERISTICS
OUTPUT VOLTAGE
vs
DATA INPUT VOLTAGE
OUTPUT VOLTAGE
vs
DATA INPUT VOLTAGE
6
6
VCC = 5 V
No Load
No Load
TA = 25°C
5
5
VO
VO – Output Voltage – V
VO – Output Voltage – V
VCC = 5.25 V
4
3
VCC = 5 V
2
TA = 70°C
4
3
TA = 25°C
2
VCC = 4.75 V
TA = 0°C
1
1
0
0
1
0
2
3
4
1
0
2
3
4
VI – Data Input Voltage – V
VI – Data Input Voltage – V
Figure 6
Figure 5
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
5
4
VCC = 5 V
TA = 25°C
VOH (IOH = – 20 mA)
3.5
4
VOH – Output Voltage – V
VOH
VO – Output Voltage – V
3
VOH (IOH = – 40 mA)
2.5
2
1.5
1
VCC = 5.25 V
VCC = 5 V
3
VCC = 4.75 V
2
1
0.5
VOL (IOL = 40 mA)
0
0
0
25
50
75
0
– 20
TA – Free-Air Temperature – °C
– 40
– 60
– 80
– 100
– 120
IOH – Output Current – mA
Figure 8
Figure 7
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SN75159
DUAL DIFFERENTIAL LINE DRIVER
WITH 3-STATE OUTPUTS
SLLS088B – JANUARY 1977 – REVISED MAY 1995
TYPICAL CHARACTERISTICS
SUPPLY CURRENT
(BOTH DRIVERS)
vs
SUPPLY VOLTAGE
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
0.6
80
No Load
TA = 25°C
70
0.5
VCC = 4.75 V
IICC
CC – Supply Current – mA
VOL – Low-Level Output Voltage – V
TA = 25°C
0.4
0.3
VCC = 5.25 V
0.2
Inputs
Grounded
60
50
40
30
Inputs
Open
20
0.1
10
0
0
20
40
60
80
100
0
120
0
1
2
IOL – Low-Level Output Current – mA
Figure 9
4
5
6
7
8
40
100
Figure 10
SUPPLY CURRENT
(BOTH DRIVERS)
vs
FREE-AIR TEMPERATURE
SUPPLY CURRENT
(BOTH DRIVERS)
vs
FREQUENCY
56
100
VCC = 5 V
Inputs Grounded
No Load
54
VCC = 5 V
RL = ∞
CL = 30 pF
80
IICC
CC – Supply Current – mA
52
ICC
I CC – Supply Current – mA
3
VCC – Supply Voltage – V
50
48
46
44
42
Input: 3-V Square Wave
TA = 25°C
60
40
20
40
38
0
36
0
25
50
75
0.1
TA – Free-Air Temperature – °C
1
4
Figure 12
POST OFFICE BOX 655303
10
f – Frequency – MHz
Figure 11
10
0.4
• DALLAS, TEXAS 75265
SN75159
DUAL DIFFERENTIAL LINE DRIVER
WITH 3-STATE OUTPUTS
SLLS088B – JANUARY 1977 – REVISED MAY 1995
TYPICAL CHARACTERISTICS
PROPAGATION DELAY TIME
FROM DATA INPUTS
vs
FREE-AIR TEMPERATURE
OUTPUT ENABLE AND DISABLE TIME
vs
FREE-AIR TEMPERATURE
30
18
VCC = 5 V
See Figures 3 and 4
tPLH
Output Enable and Disable Time – ns
Propagtion Delay Time From Data Inputs – ns
20
16
14
tPHL
12
10
8
6
4
VCC = 5 V
CL = 30 pF
RL = 100 Ω
2
25
20
tPLZ
tPZL
15
tPHZ
10
tPZH
5
0
0
0
25
75
50
0
25
50
75
TA – Free-Air Temperature – °C
TA – Free-Air Temperature – °C
Figure 13
Figure 14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
SN75159D
ACTIVE
SOIC
D
14
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
SN75159
SN75159N
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
0 to 70
SN75159N
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated