Download wall framing - LACOE Moodle Sites

BLUEPRINT READING
The ability to do basic drawing and read blueprints are valuable skills needed in all areas of construction.
Students do a simple sketch of their lab and then transfer their sketch to a drafting board where they add the
correct symbols for doors, windows, electrical and plumbing fixtures. They gain an understanding of plot
plans and how to use a floor plan to determine where walls are placed. Students use the elevation drawings
to measure window and door locations and the placement of cabinets. Blueprint Reading reinforces math and
reading skills.
CABINETMAKING
Students will identify basic tools and equipment used in the cabinetmaking trade.
They will identify and describe materials used in cabinetmaking, understand basic
techniques, and design and build a sample cabinet using 32mm technology.
Students also explore the applied mathematics of cabinetmaking.
COMMUNICATIONS
Students will identify basic tools and equipment used for communication systems
in structures. They will identify and describe applications of communication
systems, understand installation techniques for cable and internet connections,
telephone, security and lighting systems. Science and applied mathematics will be
explored
CONCRETE
Students will identify and describe basic tools, equipment, and materials used in
the concrete trade. They will gain an understanding of basic concrete and
reinforcing applications. Students will prepare, form, reinforce and pour a concrete
slab and curb, while exploring applied science and mathematics in the trade.
DRYWALL
Students assemble a steel stud wall as the basis for the rest of the activities.
Using an abrasive saw and steel studs, students measure and cut stud sections
and then fasten them in place with a drill and screws. After squaring the wall,
students cut and hang drywall pieces to form a butt joint, taper joint, and inside
and outside corners. Students apply tape, fit corner beading, and apply joint filler.
Then they sand and apply different types of decorative finish.
ELECTRICAL
Students will explore the types of wire and connections used in typical residential
electrical installations. While carefully following the onscreen video instruction,
students use a low voltage (12 volt) portable electrical panel to wire a typical
duplex residential outlet, switch loop, and a three-way switch. Additionally students
will learn how to add a circuit. They also gain an understanding of the science and
math of the electrical trade.
ESTIMATION SKILLS
Students perform material estimations for the construction of a simple house and
considerations for sustainability. They will calculate: yards of concrete, the number
of rafters, studs and plating, plumbing and electrical fixtures, doors and windows
and the quantity of roofing materials. The estimate is totaled and presented to the
instructor for review. The Estimation CTA allows students to use construction
math to calculate the cost of their labor and the materials they are using.
FINISH CARPENTRY
Students use a full size window and door trainer to install a pre-hung door and
window. They learn to use techniques for applying flashing and using shims, levels
and squares to correctly set the door and window. Once the door is installed
students use the compound mitre saw to cut and fit the door casing. They also
learn how to use a "coping" saw for crown moldings and trim work.
GREEN CONSTRUCTION
Green Construction is an exciting exploration into the process of environmentally
responsible and sustainable construction techniques that will attract a lot of
student interest. Activities include: installation and testing of a solar panel array,
installation of energy-saving plumbing components, and analysis of lighting
for electrical efficiency. Students also conduct a LEED audit.
HVAC
Students will explore the relationship between electricity consumption and heating
and cooling output using meters and testing devices. Using the HVAC trainer
students will gain an understanding of the basics of thermodynamics and explore
the properties of convection, conduction and radiation.
PLUMBING
Students learn how to cut and connect four types of pipe. They will prepare and
solder copper pipe for water, and cut and thread steel pipe for gas applications.
Additionally they explore the different applications for ABS and PVC plastic pipe.
Students assemble a drain-waste-vent system; install a sink with taps, tubes and
drain; install a toilet with base assembly; and build and test a simulated gas pipe
circuit.
POWER TOOLS
Students first learn to safely use a table saw and then use it to rip a board into
strips in preparation for gluing and clamping. The board is then dressed using the
jointer and bench top planer. Students will then use a router to create the final
pieces for assembling the lid for their custom box. They apply the same principles
to build a picture frame.
ROOF FRAMING
Whether flat, gabled, or steeply pitched, the roof not only adds style but adds
significantly to the strength of the structure. Students develop their geometry skills
while they lay out rafters. They cut and trace the rafters and cut them to size. After
cutting the ridge board, they stack the roof frame, cut and fit the lookouts
and install the fascia boards.
TILE SETTING
Students will learn how to measure, cut, set and finish both vertical and floor tile.
Using the tile setting trainer students will apply mathematics skills to layout the tile
grid. Students will cut and fit tile using several types of cutting tools, and apply
mortar and grout.
WALL FRAMING
In Wall Framing Skills students build and connect four complete walls that
include window and door sections, using industry-standard procedures. They gain
an understanding of the types of fasteners and nailing techniques used in framing.
In the framing process students gain an understanding of the terminology and
techniques used in construction.
WEATHERIZATION
Weatherization is one of the fastest growing Green construction trades. Millions of
homes in the U.S. will require some form of weatherization. This high-activity CTA
gives students the opportunity to understand the "whole-house" approach to
weatherization. Students learn about the latest weatherization techniques and
material applications. Students will demonstrate effective communication skills with
the homeowner as an integral part of a successful weatherization project.