Download LM35 Precision Centigrade Temperature Sensors (Rev. D)

Product
Folder
Sample &
Buy
Technical
Documents
Support &
Community
Tools &
Software
LM35
www.ti.com
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
LM35 Precision Centigrade Temperature Sensors
FEATURES
DESCRIPTION
•
•
•
•
•
•
•
•
•
•
•
The LM35 series are precision integrated-circuit
temperature sensors, with an output voltage linearly
proportional to the Centigrade temperature. Thus the
LM35 has an advantage over linear temperature
sensors calibrated in ° Kelvin, as the user is not
required to subtract a large constant voltage from the
output to obtain convenient Centigrade scaling. The
LM35 does not require any external calibration or
trimming to provide typical accuracies of ±¼°C at
room temperature and ±¾°C over a full −55°C to
+150°C temperature range. Low cost is assured by
trimming and calibration at the wafer level. The low
output impedance, linear output, and precise inherent
calibration of the LM35 make interfacing to readout or
control circuitry especially easy. The device is used
with single power supplies, or with plus and minus
supplies. As the LM35 draws only 60 μA from the
supply, it has very low self-heating of less than 0.1°C
in still air. The LM35 is rated to operate over a −55°C
to +150°C temperature range, while the LM35C is
rated for a −40°C to +110°C range (−10° with
improved accuracy). The LM35 series is available
packaged in hermetic TO transistor packages, while
the LM35C, LM35CA, and LM35D are also available
in the plastic TO-92 transistor package. The LM35D
is also available in an 8-lead surface-mount smalloutline package and a plastic TO-220 package.
1
2
Calibrated Directly in ° Celsius (Centigrade)
Linear + 10 mV/°C Scale Factor
0.5°C Ensured Accuracy (at +25°C)
Rated for Full −55°C to +150°C Range
Suitable for Remote Applications
Low Cost Due to Wafer-Level Trimming
Operates from 4 to 30 V
Less than 60-μA Current Drain
Low Self-Heating, 0.08°C in Still Air
Nonlinearity Only ±¼°C Typical
Low Impedance Output, 0.1 Ω for 1 mA Load
+VS
(4 V to 20 V)
LM35
+VS
OUTPUT
0 mV + 10.0 mV/°C
Figure 1. Basic Centigrade Temperature Sensor
(+2°C to +150°C)
LM35
VOUT
R1
tVS
Choose R1 = –VS / 50 µA
VOUT = 1500 mV at 150°C
VOUT = 250 mV at 25°C
VOUT = –550 mV at –55°C
Figure 2. Full-Range Centigrade Temperature
Sensor
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1999–2013, Texas Instruments Incorporated
LM35
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
CONNECTION DIAGRAMS
METAL CAN PACKAGE
TO (NDV)
+VS
SMALL-OUTLINE MOLDED PACKAGE
SOIC-8 (D)
TOP VIEW
VOUT
GND
t
Case is connected to negative pin (GND)
VOUT
N.C.
1
2
8
7
+VS
N.C.
N.C.
3
6
N.C.
GND
4
5
N.C.
N.C. = No connection
PLASTIC PACKAGE
TO-92 (LP)
BOTTOM VIEW
PLASTIC PACKAGE
TO-220 (NEB)
+VS VOUT GND
LM
35DT
+VS
GND
VOUT
Tab is connected to the negative pin
(GND).
NOTE: The LM35DT pinout is different than
the discontinued LM35DP
2
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
LM35
www.ti.com
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
ABSOLUTE MAXIMUM RATINGS (1) (2)
MIN
MAX
Supply voltage
–0.2
35
Output voltage
–1
6
V
10
mA
Output current
Electrostatic discharge (ESD) susceptibility (3)
Storage temperature
Lead temperature
–60
180
TO-92 Package
–60
150
TO-220 Package
–65
150
SOIC-8 Package
–65
150
TO Package (soldering, 10 seconds)
TO-92 and TO-220 Package (soldering, 10 seconds)
260
SOIC Package
220
Infrared (15 seconds)
°C
°C
215
LM35D
(3)
(4)
V
300
Vapor phase (60 seconds)
(2)
V
2500
TO Package
Specified operating temperature LM35, LM35A
range: TMIN to TMAX (4)
LM35C, LM35CA
(1)
UNIT
–55
150
–40
110
0
100
°C
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not
apply when operating the device beyond its rated operating conditions. See Note 1.
Human body model, 100 pF discharged through a 1.5-kΩ resistor.
Thermal resistance of the TO-46 package is 400°C/W, junction to ambient, and 24°C/W junction to case. Thermal resistance of the TO92 package is 180°C/W junction to ambient. Thermal resistance of the small outline molded package is 220°C/W junction to ambient.
Thermal resistance of the TO-220 package is 90°C/W junction to ambient. For additional thermal resistance information see table in the
APPLICATIONS section.
ELECTRICAL CHARACTERISTICS (1) (2)
LM35A
PARAMETER
Accuracy (5)
TEST CONDITIONS
TYP
TESTED
LIMIT (3)
TA = 25°C
±0.2
±0.5
TA = –10°C
±0.3
TA = TMAX
±0.4
±1
±0.4
±1
TA = TMIN
TMIN ≤ TA ≤ TMAX
±0.18
Sensor gain
(average slope)
TMIN ≤ TA ≤ TMAX
+10
+9.9,
+10.1
Load regulation (7)
0 ≤ IL ≤ 1 mA
TA = 25°C
±0.4
±1
TMIN ≤ TA ≤ TMAX
±0.5
(1)
(2)
(3)
(4)
(5)
(6)
(7)
TA = 25°C
±0.01
4 V ≤ VS ≤ 30 V
±0.02
DESIGN
LIMIT (4)
TYP
TESTED
LIMIT (3)
±0.2
±0.5
±0.3
Nonlinearity (6)
Line regulation (7)
LM35CA
±0.4
±0.35
±0.05
±1
°C
±1
±0.4
±1.5
±0.3
°C
+10
+9.9,
+10.1
mV/°C
±1
±0.5
±0.01
±0.1
UNITS
(MAX.)
±0.15
±0.4
±3
DESIGN
LIMIT (4)
±0.02
±3
mV/mA
±0.05
±0.1
mV/V
Unless otherwise noted, these specifications apply: −55°C ≤ TJ ≤ 150°C for the LM35 and LM35A; −40°C ≤ TJ ≤ 110°C for the LM35C
and LM35CA; and 0°C ≤ TJ ≤ 100°C for the LM35D. VS = 5 Vdc and ILOAD = 50 μA, in the circuit of Figure 2. These specifications also
apply from +2°C to TMAX in the circuit of Figure 1. Specifications in boldface apply over the full rated temperature range.
Specifications in boldface apply over the full rated temperature range.
Tested Limits are ensured and 100% tested in production.
Design Limits are ensured (but not 100% production tested) over the indicated temperature and supply voltage ranges. These limits are
not used to calculate outgoing quality levels.
Accuracy is defined as the error between the output voltage and 10 mv/°C times the case temperature of the device, at specified
conditions of voltage, current, and temperature (expressed in °C).
Nonlinearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the rated
temperature range of the device.
Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating
effects can be computed by multiplying the internal dissipation by the thermal resistance.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
3
LM35
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
www.ti.com
ELECTRICAL CHARACTERISTICS(1)(2) (continued)
LM35A
PARAMETER
TEST CONDITIONS
VS = 5 V, 25°C
Quiescent current (8)
67
105
56.2
LM35CA
DESIGN
LIMIT (4)
131
68
105.5
TYP
TESTED
LIMIT (3)
56
67
91
56.2
133
DESIGN
LIMIT (4)
114
68
91.5
0.2
4 V ≤ VS ≤ 30 V
0.5
2
0.5
2
+0.39
+0.5
+0.39
+0.5
1
0.2
UNITS
(MAX.)
µA
116
4 V ≤ VS ≤ 30 V, 25°C
1
µA
µA/°C
Minimum temperature In circuit of Figure 1, IL = 0
for rate accuracy
(8)
56
VS = 30 V, 25°C
Temperature
coefficient of
quiescent current
Long term stability
TESTED
LIMIT (3)
VS = 5 V
VS = 30 V
Change of quiescent
current (7)
TYP
+1.5
TJ = TMAX, for 1000 hours
+2
±0.08
+1.5
+2
±0.08
°C
°C
Quiescent current is defined in the circuit of Figure 1.
ELECTRICAL CHARACTERISTICS (1) (2)
LM35
PARAMETER
Accuracy, LM35,
LM35C (5)
Accuracy, LM35D (5)
TEST CONDITIONS
TYP
TESTED
LIMIT (3)
TA = 25°C
±0.4
±1
TA = –10°C
±0.5
TA = TMAX
±0.8
TA = TMIN
±0.8
±1.5
±1.5
±0.8
±2
Load regulation (7)
0 ≤ IL ≤ 1 mA
TA = 25°C
±0.4
±2
TMIN ≤ TA ≤ TMAX
±0.5
TA = 25°C
±0.01
4 V ≤ VS ≤ 30 V
±0.02
±0.5
±0.1
±1.5
°C
±0.5
°C
+10
+9.8,
+10.2
mV/°C
±2
±0.5
±0.01
±0.2
°C
±0.2
±0.4
±5
UNITS
(MAX.)
±2
±2
+9.8,
+10.2
4
±1.5
±0.9
+10
(7)
±1.5
±0.8
±0.9
±0.3
(6)
±1
±0.5
TA = TMIN
TMIN ≤ TA ≤ TMAX
(5)
±0.4
DESIGN
LIMIT (4)
TA = TMAX
TMIN ≤ TA ≤ TMAX
(2)
(3)
(4)
TESTED
LIMIT (3)
±0.6
Sensor gain
(average slope)
(1)
TYP
TA = 25°C
Nonlinearity (6)
Line regulation (7)
LM35C, LM35D
DESIGN
LIMIT (4)
±0.02
±5
±0.1
±0.2
mV/mA
mV/V
Unless otherwise noted, these specifications apply: −55°C ≤ TJ ≤ 150°C for the LM35 and LM35A; −40°C ≤ TJ ≤ 110°C for the LM35C
and LM35CA; and 0°C ≤ TJ ≤ 100°C for the LM35D. VS = 5 Vdc and ILOAD = 50 μA, in the circuit of Figure 2. These specifications also
apply from +2°C to TMAX in the circuit of Figure 1. Specifications in boldface apply over the full rated temperature range.
Specifications in boldface apply over the full rated temperature range.
Tested Limits are ensured and 100% tested in production.
Design Limits are ensured (but not 100% production tested) over the indicated temperature and supply voltage ranges. These limits are
not used to calculate outgoing quality levels.
Accuracy is defined as the error between the output voltage and 10 mv/°C times the case temperature of the device, at specified
conditions of voltage, current, and temperature (expressed in °C).
Nonlinearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the rated
temperature range of the device.
Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating
effects can be computed by multiplying the internal dissipation by the thermal resistance.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
LM35
www.ti.com
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
ELECTRICAL CHARACTERISTICS(1)(2) (continued)
LM35
PARAMETER
TEST CONDITIONS
VS = 5 V, 25°C
Quiescent current (8)
80
105
56.2
LM35C, LM35D
DESIGN
LIMIT (4)
158
82
105.5
TYP
TESTED
LIMIT (3)
56
80
91
56.2
161
DESIGN
LIMIT (4)
138
91.5
0.2
0.5
3
0.5
3
+0.39
+0.7
+0.39
+0.7
0.2
µA
141
4 V ≤ VS ≤ 30 V
2
UNITS
(MAX.)
82
4 V ≤ VS ≤ 30 V, 25°C
2
µA
µA/°C
Minimum temperature In circuit of Figure 1, IL = 0
for rate accuracy
(8)
(9)
56
VS = 30 V, 25°C
Temperature
coefficient of
quiescent current
Long term stability
TESTED
LIMIT (3)
VS = 5 V
VS = 30 V
Change of quiescent
current (9)
TYP
TJ = TMAX, for 1000 hours
+1.5
±0.08
+2
+1.5
+2
±0.08
°C
°C
Quiescent current is defined in the circuit of Figure 1.
Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating
effects can be computed by multiplying the internal dissipation by the thermal resistance.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
5
LM35
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS
THERMAL RESISTANCE
JUNCTION TO AIR
THERMAL TIME CONSTANT
45
40
TIME CONSTANT (SEC)
THERMAL RESISTANCE (ƒC/W)
400
300
200
T0-46
100
35
30
25
20
T0-46
15
10
T0-92
5
T0-92
0
0
0
400
800
1200
1600
0
2000
AIR VELOCITY (FPM)
1600
2000
C002
Figure 4.
THERMAL RESPONSE IN STILL AIR
THERMAL RESPONSE IN STIRRED OIL BATH
120
PERCENT OF FINAL VALUE (%)
PERCENT OF FINAL VALUE (%)
1200
Figure 3.
100
80
60
40
20
0
±20
100
80
T0-46
60
T0-92
40
20
0
±20
0
2
4
6
TIME (MINUTES)
8
0
2
4
6
TIME (SEC)
C003
8
C004
Figure 5.
Figure 6.
MINIMUM SUPPLY VOLTAGE
vs
TEMPERATURE
QUIESCENT CURRENT
vs
TEMPERATURE
(IN CIRCUIT OF Figure 1)
4.4
160
4.2
TYPICAL
IOUT = 2.0 mA
4.0
140
QUIESCENT CURRENT (A)
SUPPLY VOLTAGE (V)
800
AIR VELOCITY (FPM)
120
3.8
3.6
3.4
TYPICAL
IOUT = 1.0 mA
3.2
3.0
TYPICAL
IOUT = 0 A or 50 A
2.8
120
100
80
60
40
20
2.6
2.4
0
±75
±25
25
75
TEMPERATURE (ƒC)
125
175
C005
Figure 7.
6
400
C001
±75
±25
25
75
TEMPERATURE (ƒC)
125
175
C006
Figure 8.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
LM35
www.ti.com
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
ACCURACY
vs
TEMPERATURE (ENSURED)
200
2.0
180
1.5
TEMPERATURE ERROR (ƒC)
QUIESCENT CURRENT (A)
QUIESCENT CURRENT
vs
TEMPERATURE
(IN CIRCUIT OF Figure 2)
160
140
120
100
80
1.0
0.5
±0.5
40
±2.0
25
75
125
175
TEMPERATURE (ƒC)
LM35A
±1.0
±1.5
±25
LM35A
TYPICAL
0.0
60
±75
LM35
LM35
±75
25
±25
Figure 9.
125
175
C008
Figure 10.
ACCURACY
vs
TEMPERATURE (ENSURED)
NOISE VOLTAGE
1600
2.5
LM35D
2.0
1400
LM35C
1.5
1200
1.0
Noise (nV/—Hz)
TEMPERATURE ERROR (ƒC)
75
TEMPERATURE (ƒC)
C007
LM35CA
0.5
TYPICAL
0.0
±0.5
LM35CA
1000
±1.0
800
600
400
±1.5
LM35C
200
±2.0
0
±2.5
±75
±25
25
75
125
10
175
TEMPERATURE (ƒC)
100
1k
10k
FREQUENCY (Hz)
C009
Figure 11.
100k
C010
Figure 12.
START-UP RESPONSE
VIN (V)
6
4
2
0
0.6
VOUT (V)
0.4
0.2
0
-0.2
-20
-10
0
10
20
30
40
TIME (SEC)
50
60
C011
Figure 13.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
7
LM35
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
www.ti.com
APPLICATIONS
The LM35 is applied easily in the same way as other integrated-circuit temperature sensors. Glue or cement the
device to a surface and the temperature should be within about 0.01°C of the surface temperature.
This presumes that the ambient air temperature is almost the same as the surface temperature. If the air
temperature were much higher or lower than the surface temperature, the actual temperature of the LM35 die
would be at an intermediate temperature between the surface temperature and the air temperature, which is
especially true for the TO-92 plastic package where the copper leads are the principal thermal path to carry heat
into the device, so its temperature might be closer to the air temperature than to the surface temperature.
To minimize this problem, ensure that the wiring to the LM35, as it leaves the device, is held at the same
temperature as the surface of interest. The easiest way to do this is to cover up these wires with a bead of epoxy
which will insure that the leads and wires are all at the same temperature as the surface, and that the
temperature of the LM35 die is not affected by the air temperature.
The TO-46 metal package can also be soldered to a metal surface or pipe without damage. Of course, in that
case the V− terminal of the circuit will be grounded to that metal. Alternatively, mount the LM35 inside a sealedend metal tube, and then dip into a bath or screw into a threaded hole in a tank. As with any IC, the LM35 and
accompanying wiring and circuits must be kept insulated and dry, to avoid leakage and corrosion. This is
especially true if the circuit may operate at cold temperatures where condensation can occur. Printed-circuit
coatings and varnishes such as Humiseal and epoxy paints or dips are often used to insure that moisture cannot
corrode the LM35 or its connections.
These devices are sometimes soldered to a small light-weight heat fin to decrease the thermal time constant and
speed up the response in slowly-moving air. On the other hand, a small thermal mass may be added to the
sensor, to give the steadiest reading despite small deviations in the air temperature.
Table 1. Temperature Rise of LM35 Due To Self-heating (Thermal Resistance, θJA)
TO, no heat
sink
TO (1), small
heat fin
TO-92, no heat
sink
TO-92 (2), small
heat fin
SOIC-8, no
heat sink
SOIC-8 (2),
small heat
fin
TO-220, no
heat sink
Still air
400°C/W
100°C/W
180°C/W
140°C/W
220°C/W
110°C/W
90°C/W
Moving air
100°C/W
40°C/W
90°C/W
70°C/W
105°C/W
90°C/W
26°C/W
Still oil
100°C/W
40°C/W
90°C/W
70°C/W
Stirred oil
50°C/W
30°C/W
45°C/W
40°C/W
(Clamped to
metal, Infinite
heat sink)
(1)
(2)
8
(24°C/W)
(55°C/W)
Wakefield type 201, or 1-in disc of 0.02-in sheet brass, soldered to case, or similar.
TO-92 and SOIC-8 packages glued and leads soldered to 1-in square of 1/16-in printed circuit board with 2-oz foil or similar.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
LM35
www.ti.com
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
TYPICAL APPLICATIONS
HEAVY CAPACITIVE LOAD, WIRING, ETC.
+
2k
LM35
TO A HIGH-IMPEDANCE LOAD
OUT
v
Figure 14. LM35 with Decoupling from Capacitive Load
HEAVY CAPACITIVE LOAD, WIRING, ETC.
+
OUT
LM35
0.01 PF BYPASS
OPTONAL
TO A HIGH-IMPEDANCE LOAD
75
v
1 PF
Figure 15. LM35 with R-C Damper
CAPACITIVE LOADS
Like most micropower circuits, the LM35 has a limited ability to drive heavy capacitive loads. The LM35 alone is
able to drive 50 pf without special precautions. If heavier loads are anticipated, isolating or decoupling the load
with a resistor is easy (see Figure 14). Or you can improve the tolerance of capacitance with a series R-C
damper from output to ground (see Figure 15).
When the LM35 is applied with a 200-Ω load resistor as shown in Figure 16, Figure 17, or Figure 19, the device
is relatively immune to wiring capacitance because the capacitance forms a bypass from ground to input and not
on the output. However, as with any linear circuit connected to wires in a hostile environment, performance is
affected adversely by intense electromagnetic sources such as relays, radio transmitters, motors with arcing
brushes, and SCR transients, as the wiring acts as a receiving antenna and the internal junctions act as
rectifiers. For best results in such cases, a bypass capacitor from VIN to ground and a series R-C damper, such
as 75 Ω, in series with 0.2 or 1 μF from output to ground are often useful. These are shown in Figure 24,
Figure 24, and Figure 27.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
9
LM35
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
www.ti.com
5V
+
6.8 k
5%
VOUT = 10 mV/°C (TAMBIENT = 1 °C)
FROM + 2 °C TO + 40 °C
200
1%
v
+
HEAT
FINS
LM35
OUT
TWISTED PAIR
200
1%
v
Figure 16. Two-Wire Remote Temperature Sensor
(Grounded Sensor)
5V
+
HEAT
FINS
LM35
v
OUT
TWISTED PAIR
200
1%
VOUT = 10 mV/°C (TAMBIENT = 1 °C)
FROM + 2 °C TO + 40 °C
6.8 k
5%
OR 10K RHEOSTAT
FOR GAIN ADJUST
200
1%
Figure 17. Two-Wire Remote Temperature Sensor
(Output Referred to Ground)
10
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
LM35
www.ti.com
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
+VS
LM35
+
VOUT
v
1N914
18 k
10%
Figure 18. Temperature Sensor, Single Supply
(−55° to +150°C)
5V
+
0.01 PF
BYPASS
OPTIONAL
OUT
LM35
TWISTED PAIR
2k
1%
200
1%
2k
1%
VOUT = 10 mV/°C (TAMBIENT = 10 °C)
FROM t 5 °C TO + 40 °C
200
1%
Figure 19. Two-Wire Remote Temperature Sensor
(Output Referred to Ground)
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
11
LM35
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
www.ti.com
+ 5 V TO + 30 V
4.7 k
2N2907
IN
+
OUT
OUT
LM35
402
1%
v
62.5
0.5%
OFFSET
ADJUST
LM317
ADJ
50
Figure 20. 4-To-20 mA Current Source
(0°C to 100°C)
12
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
LM35
www.ti.com
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
+VS
(6 V to 20 V)
LM35
45.5 kO
1%
10 kO
1%
VOUT = +1 mV/°F
26.4 kO
1%
18 kO
LM385-1.2
1 MO
1%
Figure 21. Fahrenheit Thermometer
5V
LM35
Figure 22. Centigrade Thermometer
(Analog Meter)
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
13
LM35
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
www.ti.com
9V
1k
LM35
100 A,
60 mV
FULLSCALE
LM3852.5
25.5 k
Figure 23. Fahrenheit Thermometer, Expanded Scale Thermometer
(50°F to 80°F, for Example Shown)
5V
+
LM35
3.9 k
OUT
IN
REF ADC08031
1.28 V
GND
75
100k
FB
+
CLOCK
LM385
+
1 PF
SERIAL
DATA OUTPUT
ENABLE
10 k
GND
Figure 24. Temperature To Digital Converter
(Serial Output)
(128°C Full Scale)
14
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
LM35
www.ti.com
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
5V
+
LM35
16 k
OUT
8
IN
ADC0804
GND
75
INTR
1k
+
VREF
0.64 V
CS
RD
WR
GND
+
1 PF
PARALLEL
DATA
OUTPUT
2k
Figure 25. Temperature To Digital Converter
(Parallel TRI-STATE Outputs for Standard Data Bus to μP Interface.)
(128°C Full Scale)
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
15
LM35
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
www.ti.com
°F
20 k
67
68
69
70
71
72
73
74 75
76
77
78
79
80
81
82
83
84 85
86
7V
+
20 PF
20 LEDs
18
10
10
18
LM3914
1
2
3
4
5
7V
+
HEAT
FINS
LM3914
6
7
8
9
1.2 k*
1
2
3
4
5
6
7
8
9
NC
7V
VA
LM35
OUT
VC
200*
+
1 PF
1.5 k*
VB
499*
499*
1.5 k*
1 k*
RC
1k
RB
1k
RA
1k
*=1% or 2% film resistor
Trim RB for VB = 3.075 V
Trim RC for VC = 1.955 V
Trim RA for VA = 0.075 V + 100 mV/°C ×Tambient
Example, VA = 2.275 V at 22°C
Figure 26. Bar-Graph Temperature Display (Dot Mode)
16
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
LM35
www.ti.com
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
6V
6.8 k
1k
fOUT
4N28
+
8
100 k
7
LM35
5
LM131
6
GND
3
1
0.01 PF
100 k
1 PF
2
4
12 k
5k
47
0.01 PF
FULL
SCALE
ADJ
LOW TEMPCO
Figure 27. LM35 With Voltage-To-Frequency Converter And Isolated Output
(2°C to 150°C; 20 to 1500 Hz)
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
17
LM35
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
www.ti.com
BLOCK DIAGRAM
A1
1.38 VPTAT
+VS
nR1
Q1
Q2
10E
+
A2
E
VOUT = 10 mV/°C
V0
.125 R2
nR1
8.8 mV/°C
i
18
Submit Documentation Feedback
R2
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
LM35
www.ti.com
SNIS159D – AUGUST 1999 – REVISED OCTOBER 2013
REVISION HISTORY
Changes from Revision C (July 2013) to Revision D
Page
•
Changed W to Ω ................................................................................................................................................................... 1
•
Changed W to Ω ................................................................................................................................................................... 3
•
Changed W to Ω ................................................................................................................................................................... 9
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM35
19
PACKAGE OPTION ADDENDUM
www.ti.com
17-May-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM35AH
ACTIVE
TO
NDV
3
1000
TBD
Call TI
Call TI
-55 to 150
LM35AH
LM35AH/NOPB
ACTIVE
TO
NDV
3
1000
Green (RoHS
& no Sb/Br)
Call TI | POST-PLATE
Level-1-NA-UNLIM
-55 to 150
LM35AH
LM35CAH
ACTIVE
TO
NDV
3
1000
TBD
Call TI
Call TI
-40 to 110
LM35CAH
LM35CAH/NOPB
ACTIVE
TO
NDV
3
1000
Green (RoHS
& no Sb/Br)
Call TI | POST-PLATE
Level-1-NA-UNLIM
-40 to 110
LM35CAH
LM35CAZ/LFT4
ACTIVE
TO-92
LP
3
2000
Green (RoHS
& no Sb/Br)
CU SN
N / A for Pkg Type
LM35CAZ/NOPB
ACTIVE
TO-92
LP
3
1800
Green (RoHS
& no Sb/Br)
SN | CU SN
N / A for Pkg Type
-40 to 110
LM35
CAZ
LM35CH
ACTIVE
TO
NDV
3
1000
TBD
Call TI
Call TI
-40 to 110
LM35CH
LM35CH/NOPB
ACTIVE
TO
NDV
3
1000
Green (RoHS
& no Sb/Br)
Call TI | POST-PLATE
Level-1-NA-UNLIM
-40 to 110
LM35CH
LM35CZ/LFT1
ACTIVE
TO-92
LP
3
2000
Green (RoHS
& no Sb/Br)
SN | CU SN
N / A for Pkg Type
LM35CZ/LFT4
ACTIVE
TO-92
LP
3
2000
TBD
Call TI
Call TI
LM35CZ/NOPB
ACTIVE
TO-92
LP
3
1800
Green (RoHS
& no Sb/Br)
SN | CU SN
N / A for Pkg Type
-40 to 110
LM35DH
ACTIVE
TO
NDV
3
1000
TBD
Call TI
Call TI
0 to 70
LM35DH
LM35DH/NOPB
ACTIVE
TO
NDV
3
1000
Green (RoHS
& no Sb/Br)
POST-PLATE
Level-1-NA-UNLIM
0 to 70
LM35DH
LM35DM
NRND
SOIC
D
8
95
TBD
Call TI
Call TI
0 to 100
LM35D
M
LM35DM/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
SN | CU SN
Level-1-260C-UNLIM
0 to 100
LM35D
M
LM35DMX
NRND
SOIC
D
8
2500
TBD
Call TI
Call TI
0 to 100
LM35D
M
LM35DMX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
SN | CU SN
Level-1-260C-UNLIM
0 to 100
LM35D
M
LM35DT
NRND
TO-220
NEB
3
45
TBD
Call TI
Call TI
0 to 100
LM35DT
Addendum-Page 1
LM35
CAZ
LM35
CZ
LM35
CZ
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
17-May-2014
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
LM35DT/NOPB
ACTIVE
TO-220
NEB
3
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
Op Temp (°C)
Device Marking
(4/5)
0 to 100
LM35DT
LM35DZ
OBSOLETE
TO-92
LP
3
TBD
Call TI
Call TI
LM35DZ/LFT1
ACTIVE
TO-92
LP
3
2000
Green (RoHS
& no Sb/Br)
SN | CU SN
N / A for Pkg Type
LM35
DZ
LM35DZ/LFT2
ACTIVE
TO-92
LP
3
2000
Green (RoHS
& no Sb/Br)
CU SN
N / A for Pkg Type
LM35
DZ
LM35DZ/LFT4
ACTIVE
TO-92
LP
3
2000
Green (RoHS
& no Sb/Br)
SN | CU SN
N / A for Pkg Type
LM35
DZ
LM35DZ/LFT7
ACTIVE
TO-92
LP
3
2000
Green (RoHS
& no Sb/Br)
SN | CU SN
N / A for Pkg Type
LM35
DZ
LM35DZ/NOPB
ACTIVE
TO-92
LP
3
1800
Green (RoHS
& no Sb/Br)
SN | CU SN
N / A for Pkg Type
0 to 100
LM35H
ACTIVE
TO
NDV
3
1000
TBD
Call TI
Call TI
-55 to 150
LM35H
LM35H/NOPB
ACTIVE
TO
NDV
3
1000
Green (RoHS
& no Sb/Br)
Call TI | POST-PLATE
Level-1-NA-UNLIM
-55 to 150
LM35H
LM35
DZ
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
17-May-2014
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Oct-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM35DMX
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM35DMX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Oct-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM35DMX
SOIC
D
8
2500
367.0
367.0
35.0
LM35DMX/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
NDV0003H
H03H (Rev F)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated