Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Switched-mode power supply wikipedia , lookup
Lumped element model wikipedia , lookup
Electrical connector wikipedia , lookup
Valve RF amplifier wikipedia , lookup
Josephson voltage standard wikipedia , lookup
Opto-isolator wikipedia , lookup
Surge protector wikipedia , lookup
Rectiverter wikipedia , lookup
Power MOSFET wikipedia , lookup
Negative resistance wikipedia , lookup
Current mirror wikipedia , lookup
Measurement of low resistance TEP Related Topics Ohm’s law, resistivity, contact resistance, conductivity, fourwire method of measurement. Principle The resistances of various DC conductors are determined by recording the current/voltage characteristic. The resistivity of metal rods and the contact resistance of connecting cords are calculated. Equipment 1 Heat conductivity rod, Cu 1 Heat conductivity rod, Al 1 Universal measuring amplifier 2 Digital multimeter 1 Power supply 0-12 V DC/6 V, 12 V AC 1 Connection box 2 Connecting cord, l = 100 mm, yellow 1 Connecting cord, l = 250 mm, red 1 Connecting cord, l = 250 mm, blue 2 Connecting cord, l = 500 mm, red 1 Connecting cord, l = 500 mm, blue 2 Connecting cord, l = 750 mm, yellow 1 Connecting cord, l = 750 mm, blue 2 Connecting cord, l = 2000 mm, yellow 04518-11 04518-12 13626-93 07134-00 13505-93 06030-23 07359-02 07360-01 07360-04 07361-01 07361-04 07362-02 07362-04 07365-02 Fig. 1: Recording the current/voltage characteristic of a metal rod. www.phywe.com P2410101 PHYWE series of publications • Laboratory Experiments • Physics • c PHYWE SYSTEME GMBH & Co. KG • D-37070 Göttingen 1 TEP Measurement of low resistance Tasks 1. To plot the current/voltage characteristics of metal rods (copper and aluminium) and to calculate their resistivity. 2. To determine the resistance of various connecting cords by plotting their current/voltage characteristics and calculating the contact resistances. Set-up and procedure 1. Connect the metal rod to the mains with an ammeter. Measure the voltage drop across the rod at two sockets on the side, using the amplifier (four-wire method of measurement, see Fig. 1). Settings of the amplifier: Low drift, R = 10 4 Ω, Amplification: 10 3 , Timer constant: 0 sec. 2. Connect a connecting cord into the circuit in place of the metal rod, using two double sockets with cross hole (Fig. 2a). Connect the voltmeter to the sockets of the connecting cord connector (similar to the four-wire method; measuring U 1 as shown in Fig. 2). The voltage dops not only across the pure line resistor R 1 but also across the two line/plug contact resistors R 1 p as well. Fig. 2: Measuring the contact resistance and resistivity of connecting cords a) sketch of the set-up Determine the total resistance of the connecting cord with connectors by connecting the Voltmeter to the holes in the double sockets (measuring U 2 in Fig. 2). The plug/double socket contact resistances R pd are obtained by comparing U 1 and U 2 . 2 P2410101 PHYWE series of publications • Laboratory Experiments • Physics • c PHYWE SYSTEME GMBH & Co. KG • D-37070 Göttingen Measurement of low resistance TEP b) equivalent circuit diagram: R t , R pd and R 1 p are contact resistors, R 1 a line resistor. Fig. 3: Current/voltage characteristics of a copper rod and an aluminium rod. Theory and evaluation The resistivity of the metal is determined from the resistance R of the rod and its dimensions. The rod has a diameter of 2.5 cm (cross section A = 4.91x10 4 m 2 ) and is 31.5 cm long (length l ) between the two voltmeter connections. A R I (1) www.phywe.com P2410101 PHYWE series of publications • Laboratory Experiments • Physics • c PHYWE SYSTEME GMBH & Co. KG • D-37070 Göttingen 3 Measurement of low resistance TEP Ohm’s law U R I (2) The regression lines of the measured values in Fig. 3 give RCu 11.5 0.3 for the copper rod, and RA1 19.1 0.2 for the aluminium rod. The values of resistivity obtained using equation (1) are: The aluminium rod is not pure, it contains other additions. The copper wire in the cords has a cross section A of 2.5 mm 2 . Fig. 4: Current/voltage characteristics of some connecting cords of different lengths. 4 P2410101 PHYWE series of publications • Laboratory Experiments • Physics • c PHYWE SYSTEME GMBH & Co. KG • D-37070 Göttingen Measurement of low resistance TEP The line resistance R1 of the connecting cords can be calculated using (1): R1 = I A The line/plug contact resistance can be established from the difference between the line resistance R1 calculated and the resistance R1 measured. R1 is determined from the slope of the straight lines in Fig. 4. The average of the line/plug contact resistance values is: R1 R1 R2 2.1m 2 The plug/double socket contact resistance can be determined by comparing the voltages U 1 and U 2 (see Figs. 2): R pd U1 U 2 I In accordance with Figs. 2b, U1 R1 I with R1 R1 R1 p1 R1 p 2 and U 2 R2 I with R2 R1 R pd1 R pd 2 www.phywe.com P2410101 PHYWE series of publications • Laboratory Experiments • Physics • c PHYWE SYSTEME GMBH & Co. KG • D-37070 Göttingen 5 Measurement of low resistance TEP For a connecting cord 100 mm long the measured values give: R2 64.4m R1 5.6m The plug/double socket contact resistance is therefore of the order of R pd 30m 6 P2410101 PHYWE series of publications • Laboratory Experiments • Physics • c PHYWE SYSTEME GMBH & Co. KG • D-37070 Göttingen