Download LD6IC-AT

LD6IC
Catalog Number
LD6IC-AT-DIMTR
Type
Project Name
6” New Construction IC Housing for 600 lumen Triac Dimmable RL600 series Module LED lighting components
o
NE
W
IC
RATED
A Height = 7-1/4”
B Width = 7”
C Cut-out = 6-1/2”
D Length = 10”
TO BE USED WITH MODULE LED LIGHTING COMPONENT ONLY RL600 600/900 LUMEN
DESCRIPTION - 6” IC housing for use with RL600 LED series Module LED trims. Designed for new construction installations and suitable for use in insulation covered or noninsulation covered ceilings. The LD6IC-AT-DIMTR housing is engineered with a unique ‘EZ-connect’ wiring system, that when used with the RL600 trim, with Energy Star and California
Title-24 (compliances pending). The unique EZ-connect system also meets other state and national regulatory mandates. Module LED connects effortlessly to housing, virtually
eliminating mis-wiring and potential shock hazards.
NOTE - Complete system includes LD6IC-AT-DIMTR housing and Module LEDs RL600 series trim. RL600 Module LEDs trim must be ordered separately.
SPECIFICATION
HOUSING - Die-formed aluminum and galvanized steel for maximum heat dissipation
and rust protection. Housing adjusts vertically in plaster frame to accommodate 1/2“ to
1-3/8” thick ceiling. Housing is IC rated for direct contact with insulation and can be
used in IC and NON-IC applications. May be installed in 2” x 8” joist construction.
6 INCH
CONNECTION - Polarity-specific EZ-connect system engineered to match with Elite
Module LED trims. *Meets strict code requirements where Edison Base Sockets
have been banned.
NE W CO NSTRUCTION IC HO USIN G
BAR HANGERS
• Double-headed nail is securely positioned 20° down in a hammer swing position
for quick installation. Allows for easy removal and relocation and can be easily
installed into any wood material.
• One end of bar hangers hinges 90°, allowing wiring of luminaire while splices are
at eye level and below the ceiling line.
• Installing pivoting end first allows for easy access to splice box, increasing
efficiency of personal.
• Bar hanger ends have quick location tab allowing luminaire to be located easily
and accurately against the exact bottom of studs each time.
• Bar hangers can be modified to fit in 12” joist spans without removal from
housing. Simply push in completely and snap off excess ends.
• Bar hanger ends are equipped with additional holes and slots for use when local
codes require luminaires to be additionally secured.
• Notch and tab in bar hanger ends allow installation on standard commercial
T-bars and grid ceiling supports without additional modification, clips or brackets.
• Bar hangers can be positioned on either the long or short axis of the housing and
locked in position on all sides at any place along a 24” span.
JUNCTION BOX - UL Listed for through-branch circuit wiring, provided with four
½” knockouts, one ¾” knockout and four Romex knockouts with true pry-out slots
and strain clamps. Designed for straight through conduit runs.
214 • TEL: 1-877-375-5555 • FAX: 1-877-375-3333 • WEB: WWW.IUSEELITELED.COM
THERMAL PROTECTION - Standard thermal protection device guards against
improper installation and misuse of insulation material.
ELITE MODULE LED SOLD SEPARATELY - Module LEDs unique ‘EZ-connect’
wiring system is Title 24-2008 compliant when used with the LD6IC-AT-DIMTR
housing. The unique EZ-connect system also meets other state and national
regulatory mandates. System is a UL Listed disconnect system that preserves the
integrity of the energy-efficient system by insuring only Elite brand trims are used.
The EZ-connect system prevents installation of less efficient incandescent luminaires
and LEDs.
LISTING
c-UL-us listed for Damp location
c-UL-us listed for feed Through Wiring
c-UL-us listed for Direct Contact with Insulation
Covered by U.S. Patent Number: 7717390B1
Example: LD6IC-AT-DIMTR-120
LD6IC
HOUSING TYPE
LD6IC-AT-DIMTR-120
LD6IC-AT-DIMTR-277
APPLICATION
Used For Triac & Electronic Low Voltage Dimming
Provided with 277V. Step Down Transformer & is not dimmable
-
TRIM TYPE
RL663
(Adjustable
Baffle)
6 LUMENS
14W-DIMTR-120
14W-DIM10-277
-
COLOR FINISH
o 27K o W-WH
o 30K o P-BK
o 35K
o 40K
o 50K
✔ Reset
✔ Reset
ALL PRODUCTS ARE U.S. AND FOREIGN PATENT PENDING
✔ Reset
RL663
UNIVERSAL 6”- ADJUSTABLE LED RETROFIT LIGHTING MODULE
w ENGINEERED FOR VERSATILITY AND PERFORMANCE
The Elite RL663 has been engineered for New Construction, Remodel and Retrofit applications for 6 inch
downlights. Dedicated housings install the same way as our standard incandescent downlights. The module can
be adjusted up to 35 degrees vertically and rotates up to 359 degrees.
Over 620 usable lumens are directed from the luminaire to the work surface. Lighting is smooth and
comfortable, all while using 75% less energy than the equivalent 65W BR30 and 25% less than the common
18W CFL . Plus the Elite RL663 features 50,000 hours life, and California Title-24 compliance.
NE
W
w FEATURES
Greater light output than an 26W CFL or a 65W BR30 while consuming less than 14W of power.
Fits in most 6 inch downlight housings. Adjusts up to 35 degrees vertically.
w OPTICS
620
Anyone can mount a chip to a heat sink and make a down light.
Gather the light scattered by the LED chip, shape it into a functional beam with a state of the art
reflector,integrate the light through a smooth reflector to minimize brightness, then top it all off with a glare
reducing cone that has an exceptional cut-off. Now you have the Elite-engineered, superior quality, RL663
consuming less than 14 Watts and producing over 620 lumens.
INSTALLATION
NE
w DURABILITY
W
Die-cast aluminum housing and heat management system are engineered for extremely long life and service
period. Without proper heat management, any LED luminaire will fail. Our die-cast system pulls the heat from
the LED chip, allowing the continued cool operation for years. Life tests have shown the Elite RL663 light output
will be maintained at 70% of initial at 50,000 hours of operation. Our superior design allows for installation in
construction that requires the Elite Air-Shut™ system. Our LED driver is rated for 50 to 60 Htz at120V input,
produces less than 20% THD, has a power factor between 0.90 and 1.00 and is thermal protected for additional
safety.
w REPEATABLE
6 INCH
Repeatability means quality. From our chip selection process, to our driver, to the thermal management, the Elite
RL663 Module is engineered for quality. All Elite LED luminaries are rated at 80+ CRI, as rated and tested to
LM-79 and LM-80 standards by an outside laboratory, and meets the California Title-24 compliance standards.
Our stringent chip specifications to accept only those chips that produce no ultra violet light and with very
minimal infrared.
A DJ USTA BL E LED RETROFIT M ODULE
w DIMMABLE
• Utilizes industry standard V or torsion springs,
installs in most 6” incandescent down lights.
• Insert torsion springs into can and press trim
to ceiling.
The Elite RL663 lighting system is dimmable down to 10% by using an approved Incandescent dimmer
or Select Electronic Low voltage dimmers when ordered with the following option (DIMTR-120). For 277V
applications, a 0-10V dimming driver will be provided when ordered with the following option (DIM10-277).
Refer to dimming matrix for more information.
w INTERCHANGEABLE
The Elite RL663 LED system works in our dedicated (LD6IC-AT ,LD6RIC-AT) housings and our existing 6”
incandescent housings (or standard B6IC-AT ,EZ6IC-AT, B26IC-AT, B26RIC-AT, B6RIC-AT) but is also suitable for
use in most 6-inch recessed downlight housings.
w ADAPTABLE
CERTIFICATIONS
• cULus
• RoHH
• IECC
• California Title 24
• New York state
• Washington state
• Made in USA
All Elite RL663 luminaries are shipped standard with our custom engineered Edison adapter. This adapter
assembly allows the luminaries to install directly into existing Elite 6” downlight housings and most other 6-inch
downlight housings. GU24 style socket base adapters also available upon request.
w OUR WORD
The Elite RL663 is warranted for 5 years of flawless operation. As a system, we stand behind the entire Elite
product from housing to bar hangers. When the Module LED is installed in retrofit applications, only the
Module itself is warranted.
188 • TEL: 1-877-375-5555 • FAX: 1-877-375-3333 • WEB: WWW.IUSEELITELED.COM
ALL PRODUCTS ARE U.S. AND FOREIGN PATENT PENDING
RL663
UNIVERSAL 6”- ADJUSTABLE LED RETROFIT LIGHTING MODULE
iFit RL663
5 years WARRANTY
NE
W
o
35
Patent Pending
3-3/4”
6 INCH
Example: RL663-14W-DIM10-120-30K-W-WH
TYPE
RL663
620 LUMENS
o 14W-DIMTR-120
(ADJUSTABLE BAFFLE)
COLOR
o 27K
o 30K
o 35K
o 40K
o 50K
FINISH
o W-WH
OPTIONS
o GU24SA- GU24 SOCKET ADAPTER
*RECOMMENDED TRIAC AND ELECTRONIC LOW VOLTAGE DIMMERS FOR ELITE iFit663 LED SYSTEM - RL663
LUTRON DIMMERS
LUTRON SYSTEM
LEVITON DIMMERS
OTHER DIMMERS
INCANDESCENT*
HOMEWORKS HW-RPM-4A-120
INCANDESCENT*
LOW WATTAGE WIRELESS
IPI06-1LX
6673-10W
6631-LW
MAESTRO ELECTRONIC LOW VOLTAGE
LED/ CFL COMBO
IPE04-1LX
6615
DIVA ARIADNI
DIVA SKYLARK AY/TG SERIES
DV SERIES
S SERIES
ELECTRONIC LOW VOLTAGE
DIVA NOVA T NOVA T
DVELV-300P
NTLV-1000
NTELV-600
* USE OF 600 WATT INCANDESCENT
DIMMERS WILL LIMIT MAXIMUM
NUMBER OF FIXTURES TO 4, AND 7 FOR
1,000 WATT INCANDESCENT
ALL PRODUCTS ARE U.S. AND FOREIGN PATENT PENDING
MRF2-6ND
DVCL-153P
• TEL: 1-877-375-5555 • FAX: 1-877-375-3333 • WEB: WWW.IUSEELITELED.COM 189
ADJ USTABL E LED RETRO FIT M ODULE
4-3/4”
8-1/4”