Download Lecture 10 - UConn Physics

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Josephson voltage standard wikipedia , lookup

Nanogenerator wikipedia , lookup

Valve RF amplifier wikipedia , lookup

CMOS wikipedia , lookup

Nanofluidic circuitry wikipedia , lookup

Negative resistance wikipedia , lookup

Power electronics wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Schmitt trigger wikipedia , lookup

RLC circuit wikipedia , lookup

Operational amplifier wikipedia , lookup

TRIAC wikipedia , lookup

Two-port network wikipedia , lookup

Power MOSFET wikipedia , lookup

Multimeter wikipedia , lookup

Surge protector wikipedia , lookup

Electrical ballast wikipedia , lookup

Rectiverter wikipedia , lookup

Current source wikipedia , lookup

Opto-isolator wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Current mirror wikipedia , lookup

Network analysis (electrical circuits) wikipedia , lookup

Ohm's law wikipedia , lookup

Transcript
Physics 1502: Lecture 10
Today’s Agenda
• Announcements:
– Lectures posted on:
www.phys.uconn.edu/~rcote/
– HW assignments, solutions etc.
• Homework #3:
– On Masterphysics : due Friday at 8:00 AM
– Go to masteringphysics.com
Electromotive force
• Provides a constant potential difference between
2 points
e
 e: “electromotive force” (emf)
+ -
• May have an internal resistance
– Not “ideal” (or perfect: small loss of V)
– Parameterized with “internal resistance” r in series with e
• Potential change in a circuit
I
I
R
e - Ir - IR = 0
V
r
e
Power
Batteries & Resistors
Energy expended
chemical
to electrical
to heat
Rate is:
What’s happening?
Assert:
Energy “drop” per charge
For Resistors:
Charges per time
Batteries (non-ideal)
• Parameterized with
“internal resistance” r in
series with e
•
I
e: “electromotive force”
I
R
(emf) = V(I=0)
e - Ir = V
e - Ir - IR = 0
V
r
e
Power delivered to the resistor R:

Pmax when R/r =1 !
Devices
• Conductors:
Purpose is to provide zero potential difference
between 2 points.
» Electric field is never exactly zero.. All conductors
have some resistivity.
» In ordinary circuits the conductors are chosen so that
their resistance is negligible.
• Batteries (Voltage sources, seats of emf):
Purpose is to provide a constant
potential difference between 2 points.
» Cannot calculate the potential difference
from first principles.. electrical  chemical
energy conversion. Non-ideal batteries will
be dealt with in terms of an "internal
resistance".
+ OR
+ V -
Devices
• Resistors:
Purpose is to limit current drawn in a circuit.
» Resistance can be calculated from knowledge of the
geometry of the resistor AND the “resistivity” of the
material out of which it is made.
» The effective resistance of series and parallel
combinations of resistors will be calculated using
the concepts of potential difference and current
conservation (Kirchoff’s Laws).
• Resistance
Resistance is defined to
be the ratio of the applied
voltage to the current
passing through.
UNIT: OHM = W
R
I
I
V
How resistance is calculated
• Resistivity
– property of all materials
– measures how much current density j results from a
given electric field E in that material
– units are Ohm x m (W m)
• Conductivity
– sometimes used instead of resistivity
– measures the same thing as r
• Resistance
– property of an object
– depends on resistivity of its material and its geometry
• Conductance
– sometimes used instead of resistance
– measures the same thing as R
The Voltage “drops”:
Resistors
in Series
I
a
R1
b
R2
Whenever devices are in SERIES, the
current is the same through both !
a
c
This reduces the circuit to:
Reffective
Hence:
c
Another (intuitive) way...
Consider two cylindrical resistors with
lengths L1 and L2
R1
L1
V
L2
R2
Put them together, end to end to make a longer one...
Resistors in Parallel
• What to do?
• Very generally, devices in parallel have
the same voltage drop
• But current through R1 is not I !
Call it I1. Similarly, R2 I2.
I
a
I1
V
R1
d
• How is I related to I 1 & I 2 ??
Current is conserved!

R2
I
I
a
V

I2
R
d
I
Another (intuitive) way...
Consider two cylindrical resistors with
cross-sectional areas A1 and A2
A1
V
A2
R1
R2
Put them together, side by side … to make a “fatter” one with A=A1+A2 ,

Summary
R1
• Resistors in series
– the current is the same in
both R1 and R2
– the voltage drops add
V
R2
• Resistors in parallel
– the voltage drop is the same
in both R1 and R2
– the currents add
V
R1
R2
Lecture 10, ACT 1
R
R
V
R
R
• I have two identical light bulbs. First I hook them up in series. Then
I hook them up in parallel. In which case are the bulbs brighter?
(The resistors represent light bulbs whose brightness is
proportional to P = I2R through the resistor.)
A) Series
B) Parallel
C) The same
e1
R
I1
I2
e2
R
•
I3
e3
R
Kirchoff's First Rule
"Loop Rule" or “Kirchoff’s Voltage Law (KVL)”
"When any closed circuit loop is traversed, the algebraic sum of
the changes in potential must equal zero."
KVL:
• This is just a restatement of what you already know: that the
potential difference is independent of path!
• RULES OF THE ROAD:
We will follow the convention that voltage gains enter with a + sign and
voltage drops enter with a - sign in this equation.
Move
clockwise
around
circuit:
e1
e1
I
R1
- IR1
R2
- IR2
e2
- e2 = 0
Loop Example
R1
b
R4
e1
f
a
I
I
d
c
R2
e2
e
R3

KVL:

1
Lecture 10, ACT 2
• Consider the circuit shown.
– The switch is initially open and the current
flowing through the bottom resistor is I0.
– After the switch is closed, the current
12 V
flowing through the bottom resistor is I1.
– What is the relation between I0 and I1?
(a) I1 < I0
(b) I1 = I0
12 V
R
I
R
(c) I1 > I0
12 V
Kirchoff's Second Rule
"Junction Rule" or “Kirchoff’s Current Law (KCL)”
• In deriving the formula for the equivalent resistance of 2
resistors in parallel, we applied Kirchoff's Second Rule
(the junction rule).
"At any junction point in a circuit where the current can
divide (also called a node), the sum of the currents into
the node must equal the sum of the currents out of the
node."
• This is just a statement of the conservation of charge at any
given node.