Download Spec Sheet - Boston Light Source

Bruno LED
Type: ________________________
Project: ______________________
Softshine
I/D or Direct
Suspended
S P E C I F I C AT I O N S
BRM9L
__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________
LAMPING OPTIONS
BRM9L
Lumen Packages:
Specify by Low (LO) or High (HI)
1 ⁄4”
3
Nominal Delivered Lumens*
8 1⁄4”
Watts*
LO
HI
3400
4800
30
SPECIFICATIONS
Construction
Nominal 8 1⁄4” x 1 3⁄4” rectangular housing is formed
from cold-rolled steel. Die-cast end caps are
mechanically attached with no exposed fasteners.
Source
Two LED lumen packages and three available color
temperature options (3000K, 3500K and 4000K).
Optics
Softshine®-engineered optical system consists
of high performance lens, diffusers and metal
reflectors.
Finish
Finish for housing and end caps is white,
black or painted aluminum. Consult factory
for custom colors.
Controls
Optional nLight-embedded controls allow for
constant lumen management (N80) and facilitate
simple “plug-and-play” networking and control via
CAT-5e cable.
Electrical
Environment
100% post-consumer recycled cardboard box and
inserts. Biodegradable, protective luminaire bag.
Recycled kraft paper tape.
__________
_________
__________
__________
__________
Voltage Driver Type
# of
Emergency
Modules
Emergency
Type2
Switching
SSHSoftshine®
lens
X FT
(4’ increments)
______________ ______________
Mounting Type
LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP840 4000K 80+ CRI
F1/
/
T-bar ceiling (universal
mounting bracket)
F1A/ T-bar ceiling (UMB with
integrated J-box)
F2/ Hard ceiling (horizontal
J-box)
R4
R8
4’ section(s)
8’ section(s)
120
277
EZBeldoLED
dims to
black
(Blank)None
1SE
1 section
2SE 2 sections
XSE X sections
______________
_________________________________
Overall Suspension
Finish
Options
1515”
1818”
2424”
3636”
4848”
7272”
XXXX”
C110
ACG
BLK
CFG
CP
DU3
DL
ELH4
GLR
GMF
LM
MCS
N80
N100
OJB
SCEP
SLP
XXXX
Painted aluminum
(low gloss)
C210 White white (fine
textured)
C202Black
C099 Custom finish
Overall suspension is
measured from ceiling to
bottom of luminaire.
Notes:
1 Nominal distribution. Refer to photometric tests
for exact distribution.
2 Emergency type is installed in last 4’ of
luminaire sections. Separate feed required
Packaging
__________
Blank Std. 70% up; 30% down
60/40 60% up; 40% down
50/50 50% up; 50% down
40/60 40% up; 60% down
30/70 30% up; 70% down
20/80 20% up; 80% down
10/90 10% up; 90% down
0/100 0% up; 100% down
______________
Five-year warranty coverage includes luminaire
construction, LED light engine, driver and optional
nLight control device. Terms and conditions apply.
Maximum
Section Length
BRM9L
LED Color Temperature
Warranty
_________
Shielding
HI
CSA/CUS listed. Individual sections are FCC part
15 certified. LM-79 tested. Lighting Facts partner.
Luminaire
Row Length
Distribution1
3400 nominal
delivered-lumens
4800 nominal
delivered-lumens
4’ and 8’ lengths in a single section for exact
suspension spacing of 4’ and 8’. For total luminaire
length, add 5⁄8” for each flat end cap and 4” for each
sculptured end cap. Using internal joiners, 4’ and 8’
sections can be joined to form longer rows.
Validation
Luminaire Light Output
LO
Luminaire Length
LED light engine consists of modular LED boards
and 0-10V dimming driver rated for 50,000
hours (L80) at 25° C ambient temperature. Driver
input wattage is 30W for 3400 delivered-lumen
package and 45W for 4800 delivered-lumens per
4’ section. Specify 120V or 277V. Pre-wired with
16AWG fixture wire. For special circuiting or wire
gauge, consult factory. Plug-in electrical connectors
included.
Damp location label option. Ambient operating
temperature between 0° C and 25° C.
CATALOG NUMBER
__________
45
* nominal per 4’
3 Dust cover not availab+e with 0/100 distribution
4 No dimming control on emergency feed
(Blank)None
ECEmergency
circuit
SCTSingle
circuit
Adjustable cable gripper
Black cord, cord manager and canopy
Configuration, consult factory for drawings
Chicago plenum (available with F1A only)
Dust cover
Damp location label
Emergency through wiring w/separate feed
Fusing (fast blow)
Fusing (slow blow)
80% lumen management without networking
Matching feed canopy at support
nLight-enabled control module per row/zone with 80% constant lumen management
nLight-enabled control module per row/zone with NO lumen management
Offset junction box
Sculptured end caps
Sloped ceiling (for 10-45°, must be specified with F2 and OJB options)
Integrated sensor; choose options and obtain code on page 2
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: [email protected] • PeerlessLighting.com
© 2013 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Peerless Bruno” are registered trademarks of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
ƕ-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx
BRM9L Bruno LED Softshine
I/D or Direct
1
Bruno LED Softshine
Type: ________________________
Project: ______________________
I/D or Direct
Suspended
BRM9L
INTEGRATED NLIGHT MICRO SENSOR
Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number.
EXAMPLE: PDT1
Network Type & Sensor Power Source (choose one)
Sensor Type (choose one)
ADC
nLight model
nES ADCX
Daylight Dimming
Specify 0-10V dimming ballast
No occupancy sensing
PDT
nLight model
nES PDT7 ADCX
Daylight Dimming and/or Occupancy Detection
Specify 0-10v dimming ballast for daylight dimming
Specify fixed-output ballast for occupancy detection only
(daylight dimming disabled)
1*
nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack
10’ Cat-5e cable and splitter provided
2
Standalone Operation (No Networking) with Luminaire Integrated Power Pack
No Cat-5e cable provided
3*
nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel
10’ Cat-5e cable and splitter provided
Order required remote nLight Power Pack or nPanel
separately through nLight (Acuity Brands Controls)
For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide
*nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on
wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact [email protected].
WEIGHTS & SUPPORT SPACING
Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations.
STANDARD SECTIONS
Key:
4’-0 3⁄8”
22 LBS
⁄8” standard flat end plates
4” optional sculptured end plates
5
4’-1 5⁄8” O.A.
•Support or feed location
xPlease consult factory for sensor placement
8’-0”
38 LBS
8’-1 1⁄4” O.A.
PLAN VIEW
CONFIGURATIONS
Tenon “L”, “T”, “X” and straight connectors available for suspended configurations.
Reference Pattern Connector Guide for additional details.
PHOTOMETRICS
Actual performance may differ as a result of end-user environment and application.
LO
116 lm/W
3400 delivered lumens
0
183
70% up / 30% down
HI
113 lm/W
4800 delivered lumens
0
125
367
250
550
375
733
500
70% up / 30% down
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: [email protected] • PeerlessLighting.com
© 2013 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Peerless Bruno” are registered trademarks of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.ǽ
ƕ-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx
BRM9L Bruno LED Softshine
I/D or Direct
2
Bruno LED Softshine
I/D or Direct
Suspended
Type: ________________________
Project: ______________________
BRM9L
LIGHTING FACTS LABELS
LP835 HI
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: [email protected] • PeerlessLighting.com
© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
5-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx
BRM9L Bruno LED Softshine
I/D or Direct
3