Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Composition of the Atmosphere: The cubic foot of typical atmosphere composed of about 78% Nitrogen and 21% Oxygen and the remaining 1% is made up of several gases. Water is constantly being absorbed and released in the atmosphere; this action is responsible for major changes in the weather. The atmosphere is a mixture of gases that exists in fairly uniform proportion up to approximately 30 miles above the earth. (Figure 4-1) Atmosphere Levels: Troposphere is the one closest to the earth extending from the surface to an average altitude of about 6 or 7 miles. Troposphere in the mid latitudes is average about 37000 feet. The Tropopause is a thin layer of the atmosphere at the top of the troposphere; it acts as a lid to confine most of the water vapor. www.persianaviator.com 09192971130 Above the Tropopause are three more atmospheric layers. The first is the Stratosphere which extends to a height of approximately 19 to 22 miles. Above the Stratosphere are the Mesosphere and the Thermosphere. The average temperature lapse rate changes abruptly at the Tropopause, above this point in the stratosphere, temperature continues to decrease, but at a slower rate. The height of the Troposphere varies; it slopes upward from about 20000 ft at the poles to 60000 ft at the equator. It is also higher in the summer than it is in the winter. The Troposphere has the greatest impact on weather. www.persianaviator.com 09192971130 Convection: Uneven Heating of the earth`s surface causes variations in air temperature and density. Convection is defined as the circular motion that results when warm air rises and is replaced by cooler air. If the earth did not rotate, a huge convective circulation pattern would develop as air flowed from the poles to equator and back again. (Figure 4-3) Atmospheric Pressure: Variations in altimeter setting between weather reporting points are primarily caused by the unequal heating of the earth`s surface. www.persianaviator.com 09192971130 Isobars are measured in millibars and are usually drawn at four millibar intervals. High is center of high pressure surrounded on all side by lower pressure. Low is an area of low pressure surrounded by high pressure. A Ridge is an elongated area of high pressure. A Trough is an elongated area of low pressure. A Col can designate either a neutral area between two highs and two lows, or intersection of a ridge and a trough. High Pressure Good weather good visibility, calm or light winds, few clouds Ridge also normally present good weather Low Pressure Poor weather low clouds, poor visibility, PPTN, gusty wind, turbulence Weather may be very violent in the area of Trough The speed of the resulting wing depends on the strength of the Pressure Gradient. www.persianaviator.com 09192971130 Coriolis force: If the earth did not rotate, pressure gradient force would propel wind directly from high to lows. Coriolis is a deflective force that is created by the difference in rotational velocity between the equator and the poles. The velocity of the earth`s surface varies from about 900 knots at the equator to zero at the poles. Coriolis force deflects the air to the right in the northern hemisphere and to the left in the southern hemisphere. The amount of deflection produced by Coriolis force varies with latitude; it is zero at equator and increase toward the poles. It also is proportional to the speed of the air mass. Wind: Pressure gradient and Coriolis forces works in combination to create wind. Pressure gradient force cause air to move from high pressure to low pressure areas. As the air begins to move Coriolis forces deflect it to the right in the Northern hemisphere. www.persianaviator.com 09192971130 Winds in the northern hemisphere flow clock-wise around highs and counter clockwise around lows. Air flow outward and downward from a high and inward and upward toward a low. The stronger the pressure gradient, the stronger the wind. Friction causes a wind shift near the earth`s surface. Global Wind Patterns: In northern hemisphere, Coriolis force produces a three-cell circulation pattern around two semi permanent high pressure at 30˚ to 60 ˚ north latitude. Around 30 ˚ north, the flow is eastward causing air to pile up at this latitude; this creates a semi permanent high pressure area. At the surface air flows back toward the equator, this low-level southerly flow is deflected to the right again and creates the northest trade winds, Common to areas like the Caribbean. The low-level air flowing northward from high to pressure at 30 ˚also is deflected to the right by Coriolis; this creates the Prevailing Westerlies, common to the mid section of North America. The cold polar air that flows southward is deflected to the right to create the Polar Easterlies. Sea & Land Breezes: Land is warmer than water during the day; this creates the Sea Breeze, a wind that blows from the cool water to the warmer land. At night, land cools faster than water and a land breeze blows from the cooler land to the warmer water. Valley & Mountain Winds: A valley wind is created as the cooler air over the valley sinks and air close to the mountain flow upward. At night, the surface of slopes cools rapidly lowering the temperature of the air close to the surface. The cooler air flows down the slope and displaces the air in the valley, this is called mountain wind. www.persianaviator.com 09192971130 Katabatic Winds: A katabatic wind is the name given to any wind blowing down an incline. A mountain wind is one type of katabatic wind. A warm descending wind is called Foehn wind but may also be referred to locally by other names such as the Santa Ana in California and the Chinnook in the Rockies. Moisture: If the air is dry, the weather usually will be good, if the air is very moist, poor or even severe weather can occur. The amount of moisture the air can hold depends on air temperature. Change of State: Every physical process of weather is accompanied by a heat exchange. Changes in state occur through the processes of Evaporation, Condensation, Sublimation, Melting and Freezing. Evaporation is the changing of liquid water to invisible water vapor. As water vapor forms, heat is absorbed from the nearest available source. Condensation occurs when water vapor changes to a liquid. When condensation takes place, the heat absorbed by water vapor during evaporation is released. The heat released is referred to as the latent heat of condensation; it is an important factor in cloud development. Sublimation is the changing of ice directly to water vapor or of water vapor to ice. Melting is the change of ice to water. Freezing is the reverse; the heat exchange in each of these process is small and has relatively little affect on water. Water vapor is added to the atmosphere by evaporation and sublimation. www.persianaviator.com 09192971130 Humidity: Dew point is the temperature at which air reaches a state where it can hold no more water. The amount of moisture in the air depends on air temperature. Dew point is the temperature at which air becomes saturated. Visible Moisture: Clouds, fog or dew always form when water vapor condenses. As air cools to its saturation point, the processes of condensation and sublimation change invisible water vapor into state that is readily seen. Clouds and fog: A small and decreasing temperature/dewpoint spread indicates conditions are favorable for the formation of fog. When clouds form near the surface they are referred to as fog. www.persianaviator.com 09192971130 Clouds and fog usually form as soon as air becomes saturated. When the temperature/dewpoint spread reaches 4˚F (2˚C) and continue to decrease, the air is nearing the saturation point and the probability of fog and low clouds forming increases. Precipitation: Drizzle, rain, snow, hail, ice crystals are all forms of precipitation. Water droplets that remain liquid fall as drizzle or rain. Rain that remains liquid even though its temperature is below freezing is considered to be supercooled, and is referred to as freezing rain. Rain may also freeze as it falls, striking the ground as ice pallets. Ice pallets usually are evidence of freezing rain and a warmer layer of air at higher altitude. If wet snow is encountered at your flight altitude, the temperature is above freezing. With low relative humidity, rain may evaporate before it reaches the surface, when this occurs, it is called Virga. Dew & Frost: Frost forms on aircraft surfaces when the surface is at or below the dewpoint of the surrounding air and the dewpoint is below freezing. On cool, still night, surface features and objects may cool to a temperature below the dewpoint of the surrounding air, moisture then condenses out of the air in the form of dew. Atmospheric Stability: Stability is the atmosphere`s resistance to vertical motion. Stable air resists vertical motion and tends to inhibit cloud formation, precipitation and severe weather. Unstable air has a tendency to move vertically this can lead to significant cloud development, turbulence and hazardous weather. www.persianaviator.com 09192971130 Temperature & Moisture: The variations of density produce convective currents in which warm air rises and is replaced by cooler, denser air. Moisture is another factor affecting stability. Water vapor is lighter than air therefore, as moisture added to air; its density decrease and it tend to rise. You can see that the greatest instability occurs when the air is both warm and moist. Air that is both cool and dry resists vertical movement and is very stable. Rising & Decreasing Air: The temperature change is caused by a process known as adiabatic heating or cooling which is a change in the temperature during expansion or compression when no energy added to or removed from the air. You can use the actual lapse ratio to determine the stability of the atmosphere. The dry adiabatic lapse rate 3˚C/1000' The moist adiabatic lapse rate 1.1˚C to 2.8˚C /1000' The lapse rate and temperature/dewpoint spread can be used to calculate cloud bases. www.persianaviator.com 09192971130 Calculate Cumulus cloud base = Temperature – Dewpoint / 4.5 Inversions: A stable layer of air and temperature increase with altitude are features of temperature inversion. Visibility and fog, haze, smoke, low clouds Temperature inversion occurs in stable air with little or no wind and turbulence. On clear, cool night as the ground cools, its lowers the temperature on the adjacent air, if this process continues the air within a few hundred feet of the surface may become cooler than the air above it. That called frontal inversion. Observing stable & unstable air: Moist, unstable air causes the formation of cumuliform clouds and showers. Stable air generally smooth with layered or stratiform clouds. Visibility is usually restricted with widespread areas of clouds and steady rain or drizzle. Unstable air is usually bumpy with good surface visibility outside of scattered rain showers. (Figure 6-4 IRM) Clouds: Clouds are visible moisture that has condensed or sublimated onto condensation nuclei such as dust, salt, or combustion particles. Type of Clouds: Low from surface to 6500 ft AGL Cumulus – Stratocumulus – Stratus Middle from 6500 ft AGL to 23000 ft AGL Altocumulus – Altostratus – Nimbostratus High from 16500 ft AGL to 45000 ft AGL Cirrus – cirrocumulus – cirrostratus www.persianaviator.com 09192971130 Cloud with extensive vertical development from 1000 ft or less to 10000 ft or more, tops sometime exceed 60000 ft MSL Towering cumulus – Cumulonimbus Stratus Clouds are layered clouds that form in stable air near the surface due to cooling from below, low turbulence, restricted visual flying, icing condition are possible if temperature are at or near freezing, gray appearance and cover a wide area. Stratocumulus Clouds are white, puffy clouds that form as stable air is lifted; they often form as stratus layer breaks up or as cumulus clouds spread out. Cumulus clouds resulting from the heating of the earth`s surface – flat bottoms and dumb shaped tops – indicate a shallow layer of instability – expect turbulence – little icing and precipitation. Turbulence can be expected at and below the bases of fair weather cumulus. Altostratus clouds are flat – dense clouds that cover a wide area – uniform gray or gray/white – minimal turbulence – moderate icing Altocumulus clouds gray or white – patchy clouds of uniform appearance – often form when altostratus clouds start to break up – light turbulence and icing – extend over wide area – may contain highly supercooled water droplets. Nimbostratus clouds gray or black – more than several thousand feet thick – contain large quantities of moisture – create heavy icing if temperatures are near or www.persianaviator.com 09192971130 below freezing – produce widespread area of rain or snow – may merge into low stratus or stratocumulus. Cirrus clouds thin – wispy clouds – form above 30000 ft – white or light gray – exist in patches or narrow bands – sometimes blown from the tops of thunderstorms or towering cumulus clouds – form in stable air – in some cases they are an advance warning of approaching bad weather. Cirrostratus clouds thin – white – form in long bands or sheets against deep blue background – several thousand feet thick – low moisture – no icing. Cirrocumulus clouds white patchy clouds – look like cotton – form as a result of shallow convective currents at high altitude – light turbulence. Towering Cumulus clouds similar to cumulus clouds except they have more vertical development – look like large mounds of cotton with billowing cauliflower tops – brilliant white at the top to gray near bottom – indicate a fairly deep layer of unstable air – moderate to heavy turbulence with icing – often develop into thunderstorm. They contain moderate to heavy convective turbulence with icing and often develop into thunderstorms. Embedded thunderstorms are frequently obscured by massive cloud layers and usually con not be seen. Cumulonimbus clouds commonly called thunderstorms – vertical developed clouds – form in very unstable air – gray/white to black – contain large amount of moisture – many flying hazards – form when moist, unstable air is lifted. Airmasses: An airmass is large body of air with fairly uniform temperature and moisture content. It may be several hundred miles across and usually form where air remains stationary or nearly stationary for at least several days. Moist, unstable air typically has cumulus clouds. Source Source Region: The area where an airmass acquires the properties of temperature and moisture that determine its stability is called its source region. www.persianaviator.com 09192971130 A source region is usually located where air tends to stagnate. Some excellent areas are snow and ice covered Polar Regions, tropical oceans, and large deserts. The middle latitudes are poor source region because of the strong westerly winds and the continual mixing of tropical and polar airmasses. Classification: The airmasses are generally divided into polar or tropical to identify their temperature characteristics and continental or maritime to identify their moisture content. Maritime Polar Cool, moist Continental Polar cool, dry Maritime Tropical Warm, moist Continental Tropical Hot, dry Modification: Modification: As an airmass moves out of its source region, it is modified by the temperature and moisture of the area over which it moves. The degree to which an airmass is changed depends on several factors: 1. Its speed 2. Nature of the region it moves over 3. Temperature difference between the airmass and the new surface 4. Depth of the airmass Warming from below: Warming from below decrease airmass stability As an airmass moves over a warmer surface, its lower layer are heated and vertical movement of the air develops depending on temperature and moisture levels, this can result in extreme instability. Cooling from below: Cooling from below may cause smooth air and poor visibility. Cooling from below increase stability. www.persianaviator.com 09192971130 When an airmass flows over a cooler surface, its lower layers are cooled and vertical movement is inhibited. As a result, the stability of the air is increased and low clouds or fog may form. This cooling from below creates a temperature inversion and may result in low ceiling and visibility for long periods of time. Fronts: Fronts are boundaries between airmasses. Since the weather along a front often presents a serious hazards to flying. Type of Fronts: Fronts are named according to the temperature of the advancing air relative to the temperature of the air it is replacing. A cold front is one where cold air is moving to displace warmer air. In a warmer front, warm air is replacing cold air. A stationary front has no movement. Cold fronts are usually fast moving and often catch up to and merge with a slower moving warm front, when cold and warm fronts merge, they create an occluded front. Frontal discontinuities: The change between two airmasses may be very abrupt, indicating a narrow frontal zone. On other hand, the changes may occur gradually, indicating a wide and perhaps, diffused frontal zone. 1. Temperature: A change in the temperature is one of the easiest ways to recognize the passage of a front. The changes may be less abrupt at middle and high altitudes than it is at the surface. 2. Wind: www.persianaviator.com 09192971130 When you are flying across a front, you will notice a change in wind direction. Wind speed also may change. The wind always shifts to the right in the northern hemisphere. 3. Pressure: As a front approaches, atmospheric pressure usually decreases, with the area of lowest pressure lying directly over the front. Pressure changes on the warm side of the front generally occur more slowly than on the cold side. Frontal Weather: The type and intensity of frontal weather depend on several factors: 1. Availability of moisture 2. The stability of the air begin lifted 3. The speed of the frontal movement 4. Slope of the front 5. The moisture and temperature variations between two fronts Cold Front: The speed of a cold front usually dictates the type of weather associated with the front. Some general weather characteristics that are found in most cold front: 1. Cumulus clouds 2. Turbulence 3. Showery precipitation 4. Strong, gusty winds 5. Clearing sky and good visibility after the front-passage FastFast-moving cold fronts: www.persianaviator.com 09192971130 Fast-moving cold fronts are pushed along by intense high pressure systems located well behind the front. These fronts are particularly hazardous because of the steep slope and wide differences in moisture and temperature between two airmasses. When a cold front pushes into extremely moist, unstable air, a squall line often forms a head of front itself. The squall line is an area of severe weather characterized by extensive vertical clouds development and turbulence. It often develops 50 to 300 miles ahead of front. A squall line often forms 50 to 200 miles ahead of fast-moving cold front. The weather usually clears quickly behind a cold front. You will notice reduced cloud cover, improved visibility, lower temperature, and gusty surface winds following the passage of fast-moving cold front. Fast-moving cold fronts force warmer air to rise, this causes wide spread vertical cloud development along a narrow frontal zone. SlowSlow-moving cold fronts: As a slow- moving cold front meets unstable air, cumulonimbus and nimbostratus clouds may develop near the surface front, creating hazards icing and turbulence. A slow-moving cold front meeting stable air usually causes a broad area of Stratus clouds to form behind the front. Warm fronts: Steady precipitation with little turbulence usually precedes warm fronts. Warm fronts occur when warm air overtakes and replaces cooler air. They usually move at much slower speed than cold fronts. Some of the common weather patterns found in a typical warm front include: 1. Stratus clouds, if the air is moist and stable 2. Little turbulence, except in an unstable airmass. 3. Precipitation ahead of the front. 4. Poor visibility with haze or fog. www.persianaviator.com 09192971130 5. Wide area of precipitation. If the air is warm, moist and stable, stratus clouds will develop. If the air is warm, moist and unstable, cumulus clouds will develop. Stationary Fronts: Stationary fronts have qualities of both warm and cold fronts. When the opposing forces of two airmasses are relatively balanced, the front that separates then may remain stationary. The weather in a stationary front is usually a mixture of that found in both warm and cold fronts. Frontal Occlusions: A frontal occlusion when a fast-moving cold front catches up to a slow-moving warm front. The difference in temperature within each frontal system is a major factor that influence which type of front and weather are created. Thunderstorms: Thunderstorm formation requires unstable conditions, a lifting force, and high moisture levels. The lifting action may be provided by several factors, such as rising terrain (orographic lifting) fronts, or heating of earth`s surface (convection). Life cycle: The three stages of thunderstorm are: Cumulus – Mature – Dissipating The cumulus stage is characterized by continues updrafts. In the cumulus stage, a lifting action initiates vertical movement of air. Thunderstorm reaches the greatest intensity during the mature stage, which is signaled by the beginning of precipitation. www.persianaviator.com 09192971130 The resulting downdraft may reach a velocity of 2500 fpm; the down-rushing air spreads outward at the surface, producing to sharp drop in temperature, a rise in pressure, and strong, gusty surface winds. The leading edge of this wind is referred to as a gust front or the first gust. As the thunderstorm advances, a rolling, turbulent circular-shaped cloud may form at the lower leading edge of the cloud; this is called the roll cloud. A dissipating thunderstorm is characterized by downdrafts, during this stage; the upper level winds often blow the top of the cloud downwind, creating the familiar anvil shape. Type of Thunderstorms: Thunderstorms are generally classified as airmass or frontal storms. Airmass Storms: Airmass storms are usually caused by convection or orographic lifting. 1. They are usually caused by solar heating of the land, which result in convection currents that lift unstable air, and are most common during summer afternoons or in coastal areas at night. 2. Orographic lifting mountain peak 3. Nocturnal thunderstorms in late spring and summer during late night or early morning hours. Frontal Storms: Frontal thunderstorms can be associated with any type of front. 1. Warm front stratiform clouds showery precipitation 2. Cold front cumulonimbus clouds 3. Occlusions can also spawn storms A squall line is a non-frontal band of thunderstorm that contains the most severe types of weather related hazards. Thunderstorm Hazardous: www.persianaviator.com 09192971130 Thunderstorms may include lightening, hail, turbulence, gusty surface wind, or even tornadoes. The cumulonimbus is the type of cloud that produces the severe turbulence. Lightening is always associated with thunderstorms. Hail can occur at all altitude within or outside a storm. Severe turbulence often exists in a thunderstorm. Thunderstorms turbulence develop when air currents changes direction or velocity rapidly over a short distance. The strongest turbulence occurs in the shear between the updrafts and downdrafts. Funnel clouds are violent, spinning columns of air which descend from the base of a cloud. If a funnel cloud reaches the earth`s surface it is referred to as a tornado. If it touches down over water, it is called a water spout. Turbulence: There are many causes of turbulence, including wind shear, convective currents, obstruction to wind flow, clear air turbulence, and wake turbulence. If you encounter turbulence, establish maneuvering speed and try to maintain a level flight attitude. If you encounter turbulence, reduce power to slow the airplane to maneuvering speed or less. Wind Shear: Wind shear can often exist near the surface when there is frontal system, thunderstorm or temperature inversion with strong upper winds in the area. A microburst is an intense downburst which covers only a small area and has a very short lift cycle, however a downburst covers a larger area and may last up to 30 minutes. Convective Currents: www.persianaviator.com 09192971130 When sufficient moisture is present, cumulus clouds indicate the presence of turbulence. The strongest convective currents are found on hot summer afternoon. Convective turbulence is caused by currents which develop in air heated by contact with the warm surface below. Obstruction to wind flow: Mechanical turbulence when obstacles like building or rough terrain interfere with the normal wind flow turbulence develops. Mountain wave turbulence can be anticipated when the wind across a ridge are 40 knots or more, and the air is stable. The crests of the waves may be marked by lens-shaped or lenticular clouds. Rotor clouds may also form in the rotors, and cap clouds may obscure the mountain peaks. Clear Clear Air Turbulence: Clear air turbulence can take place at any altitude and is often present with no visual warning. CAT may be caused by wind shear, convective currents, or obstruction to normal wind flow. It often develops in or near the jet stream, which is a narrow band of high altitudes wind near Tropopause. Wake Turbulence: Wingtip vortices are created when an airplane generates lift, the intensity of the turbulence depends on aircraft weight, speed and configuration. The greatest vortex strength occurs when the generating aircraft is heavy, slow and in a clean configuration. Wingtip vortices tends to sink below the flight path of the aircraft which generated them and are most hazardous during light, quartering tailwind conditions. To avoid turbulence when landing behind a large aircraft, stay above the large airplane`s glide path and touch down beyond its touchdown point. www.persianaviator.com 09192971130 If a large airplane has just taken off as you approach to land, touch down well before the large aircraft`s lift off point. When taking off behind a large aircraft, lift off before the large airplane`s rotation point and climb out above or upwind of its flight path. When departing after a large aircraft has landed, lift off beyond its touchdown point. Wake turbulence can be extremely hazardous, particularly to pilot of small aircraft taking off or landing behind large aircraft. Jet engine blast is a related hazard. It can damage or even overturn a small airplane if it is encountered at close range. Reporting Turbulence: Light Slight erratic changes in altitude or attitude. Light chop is slight Moderate change in IAS, moderate chop is rapid bumps or jolts without appreciate changes in altitude or attitude. Severe Abrupt changes in altitude or attitude, large variation in IAS Extreme Aircraft practically impossible to control, may cause structural damage. Icing: Visible moisture is necessary for structural icing to form, and freezing rain usually produces the highest accumulation rate. When the temperature of the aircraft surface is 0˚C or colder, ice can build up on any exposed surface of an aircraft. www.persianaviator.com 09192971130 There are two general types of ice: Rime , Clear Mixed icing is a combination of the two rime and clear ice. RimeIce Stratus clouds + tiny water droplet + instantaneous/fast freezing + opaque appearance Clear Ice Cumulus clouds + large water droplet + slow freezing + large accumulation + difficult removal www.persianaviator.com 09192971130 If the frost is not removed from the wings before flight, it may decrease lift and increase drag, preventing the aircraft from becoming airborne. Restriction to visibility: 1. Radiation fog / Ground fog over fairly level surfaces on clear, calm, humid nights + stable air + high pressure systems 2. Advection fog low layer of warm, moist air moves over a cooler surface + cloudy skies along coastline + wind up to 15 knots will intensify the fog. www.persianaviator.com 09192971130 3. Upslope fog moist, stable air is forced up a sloping land mass + form in moderate to strong winds + under cloudy skies. *. Advection and upslope fog requires a wind for formation. 4. Precipitation-induced fog warm rain or drizzle falls through a layer of cooler air near the surface + very dense 5. Steam fog low level turbulence and icing are associated with steam fog + called sea smoke Haze, smoke, smog, blowing dust or snow restrict visibility Haze concentration very fine salt or dust + stable + sometimes extend to 15000 ft www.persianaviator.com 09192971130