Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
LEDI® NETWORK in MODE D’EMPLOI - page 3 USER GUIDE - page 49 MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine Consignes de sécurité importantes ATTENTION ! Avant de commencer l’installation de votre matériel, lisez attentivement la section suivante qui décrit les consignes de sécurité à respecter au cours de l’installation. L’installation électrique sur laquelle le matériel est raccordé doit être réalisée conformément à la norme NF C 15-100 . Cet appareil ne comporte pas d’interrupteur d’alimentation primaire : un dispositif de coupure (disjoncteur ou interrupteur sectionneur), rapidement accessible, doit être incorporé dans l’installation de câblage. Ce dispositif doit supporter les valeurs de tension et courant nominales indiquées sur l’appareil. En Europe : dans le cadre de la protection des individus et de l'environnement, il vous incombe de vous débarrasser de cet équipement dans un site de collecte prévu à cet effet (séparément des ordures ménagères). Pour de plus amples informations, contactez votre revendeur, votre site de collecte ou les autorités locales compétentes. Toute modification ou ouverture du produit sans l’accord du SAV entraîne la perte de la garantie. Toute opération de maintenance doit être effectuée hors-tension, y compris pour les systèmes reliés aux éventuelles sorties sur relais. D’une façon générale, les câbles de puissance (alimentation 220V) et de signaux (information horaire) ne doivent pas être trop proches les uns des autres, pour éviter toute perturbation. (garder quelques centimètres de distance) Gorgy Timing décline toute responsabilité en cas d’accidents ou de dommages provoqués par une mauvaise utilisation du produit. Les produits GORGY TIMING sont conformes aux normes : CE, EN 60950, EN 55022, EN 50024. 2 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 SOMMAIRE 1.1.Installation rapide................................................................................................................... 5 1.1.1. Vérifiez le contenu du carton..................................................................................... 5 1.1.2. Connectez le produit.................................................................................................. 6 1.2. Configurez votre produit........................................................................................................ 6 2.1.1. Configuration réseau manuelle.................................................................................. 6 2.1.2. Configuration des cartes de sortie............................................................................. 7 1.3. Généralités............................................................................................................................ 7 1.3.1. Principes de la synchronisation................................................................................. 7 A/ Principes de la correction d’horloge.......................................................................... 7 B/ Dialogue réseau........................................................................................................ 9 C/ Travailler avec plusieurs serveurs............................................................................. 9 1.3.2. Le logiciel client NTP............................................................................................... 10 2. Configuration complète....................................................................................11 2.1. Configuration réseau............................................................................................................11 2.1.1. Configuration par défaut...........................................................................................11 2.1.2. Changement des paramètres réseau.......................................................................11 2.1.3. Intégration dans votre réseau.................................................................................. 13 2.2. Configuration des cartes de sortie....................................................................................... 14 2.2.1. Introduction.............................................................................................................. 14 2.2.2. Configuration par défaut.......................................................................................... 14 2.2.3. Changer les réglages.............................................................................................. 14 2.2.4. Paramètres génériques........................................................................................... 15 A/ Fuseau horaire........................................................................................................ 15 B/ Politique de changement d’heure (DST : Day Saving Time)................................... 15 C/ Désactivation des sorties........................................................................................ 15 3. Interface face avant........................................................................................... 16 3.1. Conditions au démarrage.................................................................................................... 16 3.2. Affichage de l’heure............................................................................................................. 17 3.4. Conditions d’alarmes mineures........................................................................................... 18 3.5. Conditions d’alarmes majeures........................................................................................... 18 4. Interface WEB......................................................................................................... 19 4.1. Présentation........................................................................................................................ 19 4.2. Description de l’interface WEB............................................................................................ 20 4.2.1. Ecran Principal........................................................................................................ 20 4.2.2. Réglages standards................................................................................................. 21 4.2.3. Configuration SNMP ............................................................................................... 24 4.2.4. Configuration NTP .................................................................................................. 26 4.2.5. Configuration des sorties......................................................................................... 28 5. Interface SNMP . .................................................................................................... 30 5.1. Présentation........................................................................................................................ 30 5.1.1. Structure de la MIB privée pour le LEDI Network IN............................................... 31 MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 3 FRANCAIS 1. inTRODUCtion............................................................................................................. 5 6 Annexe A – Connexions............................................................................................ 35 1. Connexion pour tous les produits........................................................................................... 35 1.1. Produits 230V et 115V AC (type ‘0’)........................................................................... 35 1.2. 18/72V DC product (type ‘9’)...................................................................................... 35 2. Sortie pour carte type ‘B’ (sortie double AFNOR/IRIG-B NFS87500)..................................... 36 3. Sortie pour carte type ‘A’ (ASCII+TOP).................................................................................. 37 Annexe B – Format du code de sortie............................................................... 39 1. Carte Type ‘A’ (sortie ASCII+TOP).......................................................................................... 39 2. Carte type ‘B’ (AFNOR/IRIG-B NFS87500)............................................................................ 40 2.1. Format de la trame..................................................................................................... 40 2.2. Encodage des bits...................................................................................................... 41 Annexe C – Caractéristiques............................................................................... 42 1. Dimensions............................................................................................................................. 42 2. Spécifications électriques....................................................................................................... 42 3. Autres spécifications............................................................................................................... 42 Annexe D – Guide des codes produits............................................................... 43 1. Localisation de l’étiquette....................................................................................................... 43 2. Informations de l’étiquette...................................................................................................... 43 Annexe E – Documents complémentaires........................................................ 44 4 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 Ce document est le manuel d’utilisation pour le LEDI Network IN. Ce produit est un client NTP. L’objectif de cet appareil est de synchroniser divers équipements en utilisant le temps de référence fournit par un ou plusieurs serveurs NTP. Ce produit peut être vu comme une sorte de convertisseur qui traduit un « signal NTP » en signaux de synchronisation traditionnels (ASCII+TOP, AFNOR, IRIG-B par exemple). L’utilisation du LEDI Network IN pour la synchronisation a plusieurs avantages : ►► Vous pouvez utiliser l’architecture réseau installée grâce au protocoles Ethernet+TCP/IP biens connus . ►► L’installation est simple. ►► Une configuration et un diagnostique à distance aisée . ►► Le produit est un rack 19” 1U qui s’intègre facilement à votre installation. En utilisant le LEDI Network IN avec un serveur Gorgy Timing, vous facilitez fortement l’installation et l’utilisation. ☛☛Allez directement à la section 1.1. pour l’installation rapide 1.1. Installation rapide Cette partie contient les informations élémentaires pour l’installation du LEDI Network IN. Vous trouverez des informations complémentaires dans la partie 3. 1.1.1. Vérifiez le contenu du carton Le carton doit contenir les éléments suivants: ►► Le produit lui-même : un rack 19” 1U. • Le nom de ce produit est LEDI NETWORK IN qui est écrit sur la façade avant du rack. • Une étiquette placée sur la face arrière ou le dessus du produit donne l’identification du produit. Il doit être écrit 9257/opt (où opt dépend des cartes de sortie – voir Annexe D – Guide des codes produits). ►► Un câble d’alimentation (versions 220V~ et 115V~ uniquement). ►► Un câble réseau. ►► Un CDROM contenant les outils d’installation et de gestion. ☛☛Contactez votre revendeur s’il manque un des éléments MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 5 FRANCAIS 1. inTRODUCtion 1.1.2. Connectez le produit ►► Il est fortement conseillé de noter le numéro de série (inscrit sur l’étiquette d’identification), la localisation et un bref descriptif du produit. Vous pouvez utiliser pour cela la fiche dans Annexe E – Documents complémentaires. ►► Connectez les sorties de synchronisation à vos équipements (voir Annexe A – Connexions pour plus d’informations). ►► Connectez le LEDI Network IN à votre réseau en utilisant le câble réseau fournit. ►► Branchez le LEDI Network IN à une source de courant en utilisant le câble d’alimentation s’il est fournit. Votre système doit fonctionner immédiatement si vous utilisez un ou des serveurs NTP Gorgy Timing et qu’il y a un serveur DHCP sur votre réseau. Après une étape d’apprentissage de 3 minutes, le LEDI Network IN active ses sorties et commence à générer du temps UTC. Cependant, Gorgy Timing vous recommande d’inscrire pour chaque produit son emplacement physique. Ceci est possible grâce au logiciel GTNetMng fournit sur le CDROM. Pour plus d’informations, voir la partie 31.2. 1.2. Configurez votre produit 2.1.1. Configuration réseau manuelle Les produits NTP Gorgy Timing sont configurés en usine pour récupérer automatiquement une adresse IP. Deux mécanismes sont utilisés : 1. Si un serveur DHCP est présent sur votre réseau, le produit récupère une adresse automatiquement. Ceci assure la compatibilité de l’adresse IP avec votre réseau. 2. Si aucun serveur DHCP n’est présent, le produit prend automatiquement une adresse IP grâce au mécanisme AutoIP. Dans ce cas, l’adresse sera 169.254.x.y (où x et y sont compris entre 0 et 255). Si le serveur et le client ont démarré tous deux dans ce mode, il devraient fonctionner ensemble correctement, mais leurs adresses IP seront peut-être incompatibles avec d’autres appareils présents sur le réseau.1 1/ Il se peut par exemple que vous n’ayez pas la possiblité de configurer le LEDI Network IN par un navigateur WEB. 6 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 L’identificateur DHCP par défaut est CRnnnnnn (nnnnnn est le numéro de série du produit).2 Vou pouvez changer cet identificateur grâce au logiciel GtNetMng, ou à travers l’interface WEB, comme décrit dans les parties 31.2 et 52.2. Si vous n’avez pas de serveur DHCP ou que vous souhaitez configurer vous-même les paramètres réseau, utilisez l’outil GTNetMng sur le CDROM pour changer les paramètres réseau. Veuillez vous référer à la partie 31.2 pour plus d’informations. ☛☛N’hésitez pas à contacter votre administrateur réseau pour la configuration du LEDI Network IN. Il peut vous aider à optimiser votre installation réseau 2.1.2. Configuration des cartes de sortie Par défaut, toutes les cartes de sortie fournissent l’heure UTC. L’heure reçue du serveur NTP est directement envoyée en sortie. Chaque carte peut-être configurée pour fournir plusieurs heures locales. Cette configuration est effectuée au travers d’un navigateur WEB (voir la partie 32). 1.3. Généralités Cette partie décrit les concepts généraux du produit LEDI Network IN. Elle permet de comprendre le fonctionnement du produit dans différentes circonstances. Le logiciel NTP client est le cœur du LEDI Network IN. Il effectue toute la synchronisation, la gestion du matériel et fournit les informations pour l’interface WEB et pour le protocole SNMP. 1.3.1. Principes de la synchronisation A/ Principes de la correction d’horloge Le but de la synchronisation est que deux horloges indiquent la même heure. Dans le cas d’une synchronisation basée sur le NTP, l’horloge du LEDI Network IN doit avoir la même heure que celle du serveur NTP. 2/ Certains serveur DHCP peuvent enregistrer le nom DHCP dans le DNS. Dans ce cas, vous pouvez accéder au LEDI Network IN directement par son nom DHCP au lieu de son adresse IP. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 7 FRANCAIS 1. inTRODUCtion Pour réaliser cette synchronisation, le logiciel client NTP compare en permanence les deux horloges et calcule les informations suivantes : ►► Le décalage : C’est la différence entre l’heure de l’horloge serveur, et celle de l’horloge cliente. Par exemple, si l’horloge serveur indique2:10:13 et que l’horloge cliente indique 2:11:14, alors le décalage est –1 :01 . ►► La dérive : C’est la différence de fréquence entre les deux horloges. Quand la dérive est nonnulle et sans correction d’horloge, le décalage entre les horloges augmente ou diminue, en fonction du signe de la dérive.3 Le schéma suivant montre l’évolution des deux horloges avec et sans décalage : Heure serveur Dérive nulle Heure client Heure serveur Heure client Evolution dans le temps Heure serveur Heure serveur Dérive constante Heure client Heure client L’objectif de la synchronisation d’un client NTP sur un serveur NTP est de réduire autant que possible le décalage et la dérive. La précision et la stabilité de l’horloge du client sont étroitement liés à l’efficacité de ce time processus de réduction. server Drift is null : client time server time client time Evolution during time 3/ La présence d’une dérive a plusieurs causes possibles. Généralement, elle est due à la différence de température entre les deux horloges. server time server time 8 Drift is constant : Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 client time client time B/ Dialogue réseau Le décalage et la dérive réel de l’horloge du LEDI Network IN par rapport à celle du serveur NTP sont estimés d’après un décalage mesuré. Ce décalage est calculé en soustrayant la date de l’horloge client à celle de l’horloge serveur. Périodiquement, le client estime le décalage actuel d’après le serveur. Cette mesure est effectuée grâce à un mécanisme de transmission de messages, tel qu’on peut le voir ci-dessous : Coté client Demande l’heure du serveur Réseau Coté server Envoie l’heure serveur actuelle Reçoit la réponse Sur un LAN, il suffit de quelques millisecondes entre la requête de la date par le client, et le moment où il reçoit la réponse. Ce retard est dû au délai de transmission sur le réseau. Il peut varier en fonction de la charge du réseau ou de la charge du serveur NTP. Plus grave, le temps de transmission du client au serveur n’est généralement pas le même que du serveur au client. En réalité, sur une grande période de temps, la somme des différences entre les délais de transmission client-serveur et serveur-client vaut zéro. L’algorithme du client NTP inclue dans le LEDI Network IN est conçu pour compenser les délais de transmission et pour moyenner les mesures. C/ Travailler avec plusieurs serveurs Le logiciel client NTP a le possibilité de travailler avec plusieurs serveurs NTP (jusqu’à 3). Quand un serveur ne répond pas, répond trop lentement ou n’envoie pas suffisamment de réponses, le logiciel client NTP utilise un autre serveur. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 9 FRANCAIS 1. inTRODUCtion 1. inTRODUCtion 1.3.2. Le logiciel client NTP Etats du logiciel NTP Voici les différents états du logiciel client NTP : Démarrage Recherche les serveurs . Apprentissage du milieu Auto-détection Apprentissage du milieu Erreur Apprentissage Activer les sorties Pas de réponse Travail Commutation Commutation OK Voici la signification de ces états: ►► Démarrage : Le logiciel démarre, il initialise et vérifie le matériel si besoin . ►► Auto-détection : L’autodétection des serveurs est activée. Le client essaie de trouver des serveurs Gorgy Timing. Il faut détecter au moins un serveur pour quitter cet état . ►► Apprentissage : Le logiciel client NTP a détecté un ou plusieurs serveurs Gorgy Timing (auto-détection activée) ou travaille avec des serveurs configurés. Dans cet état, le logiciel étudie les propriétés du réseau. Jusqu’à 3 minutes sont nécessaires pour terminer cette étape. ►► Travail : Fonctionnement normal, le client NTP évalue en permanence son décalage et sa dérive par rapport au serveur: ►► Commutation : Comme trop peu de réponses sont reçues du serveur actuel, le client essaie un autre serveur. Attention ! Le LEDI Network IN peut fonctionner seulement un certain temps sans synchronisation. Passé un certain délai, il désactive toutes les cartes de sortie et retourne à l’état de démarrage.4 4/ L’autonomie du LEDI Network IN dépend du temps écoulé depuis son démarrage, les caractéristiques du réseau, et de la précision désirée. 10 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 2. Configuration complète Cette partie contient les informations pour la configuration complète du produit. Elle doit être utilisée pour la configuration fine du réseau, et pour l’activation des cartes de sortie. 2.1. Configuration réseau 2.1.1. Configuration par défaut Le LEDI Network IN est configuré pour récupérer automatiquement une adresse IP d’un serveur DHCP. Au démarrage, le produit émet une requête DHCP pour obtenir une adresse IP. Cette requête contient un identificateur DHCP. Deux cas se présentent : ►► Si un serveur DHCP est installé sur le réseau, il enregistre l’identificateur DHCP et renvoie une adresse IP. Le LEDI Network IN commence alors à travailler avec cette adresse. ►► Si aucun serveur DHCP n’est installé, le LEDI Network IN utilise automatiquement une adresse IP par défaut, de type 169.254.x.y (avec x et y compris entre 0 et 255). L’identificateur DHCP par défaut du produit est CRnnnnnn, avec nnnnnn le numéro de série sur 6 chiffres. Le numéro de série est indiqué sur d’étiquette d’identification sur le dessus ou sur le dessous du produit. L’identificateur SNMP par défaut du produit (visible à partir d’un navigateur SNMP (voir partie 6) ou d’un navigateur WEB) est LediNtpRacknnnnnn, avec nnnnnn le numéro de série sur 6 chiffres. 2.1.2. Changement des paramètres réseau Utiliser le logiciel GTNetMng fourni sur le CD-ROM pour configurer votre appareil: ►► Insérer le CDROM dans le lecteur. Lancer le logiciel GTNetMng localisé dans le répertoire Common\Configuration5 5/ Par exemple, si votre lecteur CD a la lettre E:, le logiciel GTNetMng se trouve en E:\Common\Configuration\GTNetMng.exe MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 11 FRANCAIS 2 ►► L’outil GTNetMng affiche automatiquement les produits Gorgy Timing installés sur votre réseau. Chaque ligne contient des informations sur un produit connecté, comme montré ci-dessous: Nom de l’appareil (GT LEDI NTP in’rack client) Numéro de série (776657) Localisation (board40/rack02) Adresse Ethernet (MAC) de l’appareil Localisation du produit ►► Double-cliquez sur la ligne du produit que vous souhaitez configurer. La fenêtre suivante s’affiche : Nom, numéro de série et localisation Adressse IP actuelle Masque de sousréseau Adresse MAC Identificateur DHCP ►► Entrez les paramètres réseau et la localisation physique et cliquez sur le bouton Set!. 12 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 2. Configuration complète Vous n’avez à changer aucun réglage réseau pour les cas suivants : ►► Vous avez un serveur DHCP et suffisamment d’adresses IP réservées pour le produit. ►► Vous n’avez pas de serveur DHCP mais vous n’avez pas besoin d’accéder à l’appareil par son interface WEB ou SNMP. Dans ce cas, le mécanisme AutoIP affectera automatiquement une adresse IP, mais cette adresse sera probablement incompatible avec votre réseau. Certains serveurs DHCP ont la capacité d’enregistrer l’appareil dans le DNS. Dans ce cas, le nom enregistré est l’identificateur DHCP. Vous pouvez ensuite accéder à l’appareil au travers d’un navigateur WEB ou SNMP. Par exemple, si vous donnez comme nom DHCP inrack3 à votre LEDI Network IN, il vous suffit de taper inrack3 dans le champs d’adresse de votre navigateur WEB. Si vous avez plusieurs produits connectés à votre installation, il est fortement recommandé de suivre les étapes suivantes : ►► Utilisez le document fourni dans Annexe E – Documents complémentaires (Vue résumée de l’installation) et inscrivez le numéro de série et la localisation physique pour chaque produit pendant l’installation et la connection. ►► Lancez GtNetMng sur un PC connecté sur le même réseau que celui du produit. Tous les produits GT devraient apparaître avec leurs numéros de série. Entrez le numéro de série et la localisation en utilisant le document rempli à l’étape précédente. ►► Vous pouvez garder ce document pour une prochaine utilisation. ☛☛Vous trouverez le document Vue résumée de l’installation au format WORD sur le CD-ROM, dans le répertoire English\LEDI Network IN\docs\ installation.doc. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 13 FRANCAIS 2.1.3. Intégration dans votre réseau 2.2. Configuration des cartes de sortie 2.2.1. Introduction Votre LEDI Network IN est fourni avec jusqu’à 4 cartes de sortie. Chaque carte de sortie est étroitement synchronisée sur le code horaire NTP reçu du serveur NTP. Chaque carte agit comme une sorte de traducteur qui reçoit l’heure du logiciel NTP et fournit un code horaire spécifique. Il existe 2 types de cartes: ►► ASCII+TOP (carte type ‘A’). ►► AFNOR (carte type ‘B’). Vous pouvez librement utiliser et copier le tableau Configuration des appareils dans l’Annexe E – Documents complémentaires. 2.2.2. Configuration par défaut Quand vous recevez ce produit Gorgy Timing, toutes les cartes de sortie sont configurées pour fournir l’heure UTC et le temps est constant toute l’année (pas de changement d’heure été/hiver, ou DST Day Saving Time). L’afficheur en face avant est géré comme une carte de sortie et peut-être configurée de la même manière. 2.2.3. Changer les réglages Ouvrez le site WEB du LEDI Network IN (voir partie 5). Cliquez sur le bouton . La configuration actuelle de votre produit apparaît sur l’écran (montré ci-dessous pour le modèle 9257/ A): Dans cet écran, vous pouvez régler chaque carte indépendamment (voir la partie 52.5). Quand vous avez changé les réglages, cliquez sur le bouton . La modification devrait apparaître immédiatement à la sortie ou à l’écran. 14 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 2.2.4. Paramètres génériques Toutes les cartes de sorite et l’afficheur peuvent être configurés indépendamment. Le fuseau horaire et la politique de changement d’heure (DST) peuvent être réglées. A l’exception de l’afficheur, toutes les cartes de sortie peuvent être désactivées. A/ Fuseau horaire Le fuseau horaire est un décalage de temps qui peut être ajouté ou retiré du temps reçu grâce au protocole NTP (qui est en heure UTC) pour générer l’heure locale. Par exemple, en France, l’heure locale est GMT + 1:00. Si vous souhaitez qu’une carte génère l’heure locale, utilisez l’interface WEB et réglez le décalage à GMT +1:00. B/ Politique de changement d’heure (DST : Day Saving Time) En plus du fuseau horaire, beaucoup de pays appliquent leur politique de changement d’heure. L’année est ainsi coupée en 2 parties : en été, 1 heure est ajoutée au temps (après la correction du fuseau horaire), en hiver seule est appliquée la correction du fuseau horaire. ☛☛N’oubliez pas de sélectionner le pays approprié dans l’interface WEB. C/ Désactivation des sorties Vous pouvez également désactiver la sortie d’une care si besoin. La désactivation a les effets suivants : ►► Pour la carte ASCII + TOP, la trame de temps n’est plus générée, et la sortie TOP est à l’état ouvert (relais et collecteur ouvert). ►► Pour la sortie AFNOR, la porteuse n’est plus modulée. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 15 FRANCAIS 2. Configuration complète 3. Interface face avant L’interface de l’écran en face avant peut afficher jusqu’à 16 caractères. Deux boutons vous permettent soit d’afficher la configuration, soit d’effectuer un redémarrage global. L’afficheur est utilisé par le LEDI Network IN pour montrer l’heure actuelle et les différentes conditions d’alarmes. Redémarrer le LEDI NTP in’rack Commuteraffichage heure UTC/heure locale 3.1. Conditions au démarrage Au démarrage, l’heure et la date du LEDI Network IN ne sont pas valides et ne sont dons pas affichés. Ainsi, vous voyez les messages suivant : ►► Quand l’appareil démarre, tous les points de l’afficheur sont allumés. ►► Durant l’initialisation du matériel, le texte suivant est affiché: ►► Si aucun serveur n’est configuré par l’utilisateur, le LEDI Network IN essaie de détecter les serveurs GT, et affiche ce message: 16 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 ►► Si l’étape d’auto-détection échoue, le message suivant apparait, jusqu’à ce qu’un serveur GT soit disponible sur réseau: ►► S’il y a au moins un serveur GT ou que l’utilisateur a configuré manuellement les serveurs, le LEDI Network IN entre dans son étape d’apprentissage et affiche le texte suivant : 3.2. Affichage de l’heure Quand aucune alarme n’est activée et que le LEDI Network IN est correctement synchronisé sur un serveur, l’heure actuelle du serveur est affichée en permanence. L’écran affiche alternativement l’heure et la date comme montré ci-dessous : • Quand l’afficheur est configuré pour montrer l’heure UTC, les informations suivantes sont affichées alternativement : • Quand l’afficheur est configuré pour montrer l’heure locale, les informations suivantes sont affichées alternativement : MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 17 FRANCAIS 3. Interface face avant 3. Interface face avant 3.4. Conditions d’alarmes mineures L’unique alarme mineure indique que le serveur actuellement utilisé pour la synchronisation ne répond pas (ou pas correctement). Dans ce cas, le LEDI Network IN essaie d’autres serveurs, et l’afficheur indique alternativement l’heure (comme décrit dans la partie précédente) et les informations suivantes : 3.5. Conditions d’alarmes majeures Il existe deux alarmes différentes: ►► Si la LEDI Network IN ne peut pas contacter un serveur NTP, il affiche en alternance le message suivant et l’heure et la date: ►► Si aucun serveur NTP n’a été trouvé au bout d’un certain temps, le LEDI Network IN désactive ses sorties et affiche le message clignotant suivant: 18 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 4. Interface WEB Le LEDI Network IN peut être configuré et supervisé à travers une inerface WEB. Cette interface vout permet de : ►► gérer les paramètres réseau. ►► gérer les paramètres SNMP. ►► gérer et diagnostiquer le logiciel client NTP lui-même. ►► gérer et diagnostiquer les cartes de sortie. Chaque LEDI Network IN intègre son propre serveur WEB qui délivre une page WEB. Ce site WEB est un applet JAVA . si besoin une JVM (Java Virtual Machine) vous est fournie sur le CD-ROM, dans le répertoire Common\JAVA. Pour accéder au site WEB, entrez l’adresse du LEDI Network IN dans le champs d’adresses de votre navigateur WEB (comme ci-dessous), et appuyez sur Entrée. 6 Le chargement de l’applet JAVA prend environ 20 secondes. Si le chargement échoue, il peut y avoir plusieurs raison à cela : 1. l’adresse IP n’est pas valide. 2. un problème sur le réseau 7 empèche votre PC de se connecter au LEDI Network IN. 3. vous n’avez pas de JVM (Java Virtual Machine) installée sur votre PC. Dans les deux premiers cas, vérifiez l’adresse IP de votre LEDI Network IN et votre configuration réseau. Dans le dernier cas, vous devez installer la JVM (voir Common\JAVA sur le CDROM). 6: Si vous avez configuré votre LEDI Network IN en mode DHCP et que votre serveur enregistre automatiquement l’identificateur DHCP dans le DNS, vous pouvez entrer le nom DHCP au lieu de l’adresse IP 7/ Vérifiez en particulier la configuration de votre navigateur WEB. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 19 FRANCAIS 4.1. Présentation 4.2. Description de l’interface WEB 4.2.1. Ecran Principal Voici l’écran qui doit apparaître lorsque vous accédez au sit WEB du LEDI Network IN. Les quatre premiers boutons à gauche de l’écran permettent d’accéder aux panneaux suivants: 1. 2. 3. 4. Standard: informations concernant le produit et configuration des paramètres réseau. Voir la partie 2.2. SNMP: configuration des paramètres SNMP. NTP: diagnostic et configuration du comportement du logiciel NTP. Output: diagnostic et configuration des cartes de sortie et de l’afficheur. Le bouton Set Up! rafraichit instantanément la configuration du LEDI Network IN avec les nouveaux paramètres entrés. Ces paramètres sont alors stockés en permanence dans une EEPROM. ATTENTION. La modification de certains paramètres nécessitent le redémarrage du LEDI Network IN. Si vous changez ces paramètres et cliquez sur le bouton Set Up!, le LEDI Network IN redémarre avec les nouveaux paramètres et il faut attendre 3 minutes avant que les sorties ne soient réactivées. 20 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 4. Interface WEB Lorsque vous cliquez sur le bouton Standard, les paramètres réseau et les informations sur le produit sont affichés ainsi : En haut, vous pouvez contrôler les paramètres réseau et le mot de passe WEB. En bas se trouvent des informations sur le produit. Paramètres réseau ATTENTION. Si vous cliquez sur Set Up! Après avoir changé un ou plusieurs paramètres réseau, le LEDI Network IN doit redémarrer pour utiliser ces nouveaux paramètres. Pendant le redémarrage, et 3 minutes après, les sorteis sont désactivées. Voici les différents paramètres: ►► IP mode Indique si le LEDI Network IN fonctionne en adresse IP fixe (entrée dans le champs IP address) ou avec le protocole DHCP (l’identificateur DHCP est entré dans le champs DHCP identifier). MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 21 FRANCAIS 4.2.2. Réglages standards ►► IP address Indique l’adresse IP affectée au réseau. Une adresse IP est composée de 4 numéros séparés par un point. Chaque numéro s’étend de 0 à 255. ►► DHCP identifier Identificateur utilisé quand le LEDI Network IN est configuré en mode DHCP. Il est composé d’au maximum 8 lettres. Sa valeur par défaut est CRnnnnnn (où nnnnnn est le numéro de série sur 6 chiffres). ►► Network submask Indique la taille du réseau que vous utilisez. Par exemple, un masque se sousréseau de 255.255.255.0 indique que seul le dernier numéro de l’IP change (dans l’exemple ci-dessus, l’adresse dans le réseau peut varier entre 192.168.10.1 à 192.168.10.254)8. ►► Gateway address Si vous voulez que le LEDI Network IN communique avec d’autres appareils en dehors du réseau local, vous devez indiquer une passerelle (gateway) qui sera utilisée pour sortir du réseau local. ►► Without gateway Cochez cette case si vous n’avez pas de passerelle sur votre réseau ou que vous ne souhaitez pas l’utiliser. Informations sur le produit Voici une description de la zone d’informations sur le produit:: ►► Hardware GT serial number Affiche le numéro de série Gorgy Timing du produit. C’est un numéro à 6 chiffres qui doit être identique à celui collé sous ou dernière le rack . ►► Hardware Product code Affiche le code de base Gorgy Timing du produit sans option (9257 pour un LEDI Network IN). ►► Ethernet Interface (MAC) Address Indique l’adresse MAC de l’interface Ethernet du LEDI Network IN. ►► Ethernet Interface Adapter Serial number Indique le numéro de série de l’interface Ethernet du LEDI Network IN. Cette information peut être utile pour la maintenance. 8/ Si vous configurez plusieurs appareils pour communiquer sur le même réseau, vous devez avoir le même masque de sous-réseau. 22 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 4. Interface WEB ►► Firmware Version/Release Date Version du logiciel fonctionnant sur le LEDI Network IN et la date du dernier logiciel produit (au format anglais yymmdd, par exemple 021010 pour le 10 Octobre 2002). ►► Last reboot reason Indication sur la raison du dernier redémarrage du LEDI Network IN. Protection de l’accès au site WEB Si vous souhaitez protéger l’accès aux paramètres du LEDI Network IN, vous pouvez spécifier un mot de passe. Vous devez pour cela entrer le même mot de passe dans les zones Enter password et Confirm password. Si vous ne voulez pas protéger les paramètres, cochez la case Without password. Quand un mot de passe est activé, il sera demandé à la prochaine connexion. Dans ce cas, l’écran principal a cette apparence MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 23 FRANCAIS ►► Firmware DescriptionCourte description du logiciel fonctionnant sur le produit. 4.2.3. Configuration SNMP Quand vous cliquez sur le bouton SNMP, les paramètres SNMP sont affichés ainsi : Le protocole SNMP standardisé fournit un moyen de récupérer des informations et des alarmes du LEDI Network IN.9 L’accès à ces informations (la MIB) peut être “protégé” par un mot clé, le Community Name. Les alarmes sont envoyées à un navigateur SNMP localisé sur un ordinateur identifié par son adresse IP. Jusqu’à 5 adresses IP de “traps” (Trap address) peuvent-être spécifiées, ce qui permet de gérer les alarmes sur 5 ordinateurs différents. Le nom du système SNMP, sa localisation, et un contact peuvent être configurés sur cet écran. Ces informations sont enregistrées dans la branche système de la MIB et peuvent être affichées grâce à un navigateur SNMP, ou avec l’outil GTNetMng (voir la partie 31.2). Par convenance, les alarmes peuvent être envoyées par le protocole SYSLOG qui est implémenté le plus souvent sous UNIX®. 9/ Voir la partie 6 pour plus d’informations sur le SNMP 24 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 4. Interface WEB Voici une description des champs de cet écran: ►► Trap address #1..#5 Adresses des ordinateurs auxquels vont être envoyées les alarmes SNMP. Si vous n’utilisez pas une adresse, cochez la case No. ►► SYSLOG address #1..#2 Adresses des ordinateurs auxquels vont être envoyées les alarmes SYSLOG. Si vous n’utilisez pas une adresse, cochez la case No. ►► SYSLOG File Id dentifie le fichier à utiliser sur l’ordinateur distant pour le protocole SYSLOG. ►► Community name Un simple mot clé nécessaire dans un navigateur SNMP pour accéder aux informations SNMP. Un mot clé doit avoir 8 lettres au maximum. ►► System name Un nom que vous pouvez donner au LEDI Network IN. Ce nom apparaît dans la variable sysName de la branche système de la MIB. La valeur initiale est LediNtpRacknnnnnn (où nnnnnn est le numéro de série du produit). ►► System location Une éventuelle description de la localisation physique du LEDI Network IN. Ce nom apparaît dans la variable sysLocation de la branche système de la MIB. Il n’y a pas de valeur par défaut. ►► System contact Personne à contacter en cas de problème avec le LEDI Network IN. Cette information apparaît dans la variable sysContact de la branche système de la MIB. Il n’y a pas de valeur par défaut. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 25 FRANCAIS Description 4.2.4. Configuration NTP Quand vous cliquez sur le bouton NTP, la configuration de la synchronisation du LEDI Network IN est affichée comme ci-dessous: Le LEDI Network IN peut être synchronisé sur trois serveurs NTP au plus. En réalité, le logiciel client NTP n’utilise qu’un seul serveur à la fois, mais peut commuter sur un autre serveur s’il n’y a pas ou trop peu de réponses. Le panneau de configuration NTP montre le mode de synchronisation utilisé par le serveur ou sélectionné par le logiciel client NTP. Il montre ainsi les serveurs définis par l’utilisateur ou détectés par le logiciel. Description La partie droite de cet écran montre la configuration actuelle utilisée par le logiciel client NTP: Il affiche les différents serveurs utlisés pour la synchronisation et le mode actuel de synchronisation (sur l’écran ci-dessus, il n’y a qu’un seul serveur à l’adresse IP 192.168.10.124). De plus, cet partie de l’écran montre le serveur actuellement utilisé pour la synchronisation (avec un bandeau affichant Active). Si une commutation est en cours, le bandeau affiche Trying. 26 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 La partie gauche de l’écran NTP vous permet de configurer le mode de synchronisation et les serveurs NTP utilisés: Si vous sélectionnez la case Auto-detection, le LEDI Network IN essai d’utiliser les serveurs GT NTP présents sur votre réseau et d’avoir le mode de synchronisation le plus approprié. Si vous ne sélectionnez pas la case Auto-detection, vous devez indiquer vous-même le mode de syncronisation et les serveurs NTP à utiliser. La table suivante peut vous aider à choisir les paramètres les plus appropriés: One server Nb de serveurs NTP utilisés 1 Two servers 2 Three servers 3 Mode MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine Description Utilise un seul serveur pour la synchronisation Utilise le premier serveur au démarrage. Si ce serveur est défaillant, commute sur le second serveur. Si le second est défaillant, commute sur le premier, et ainsi de suite… Utilise le premier serveur au démarrage. Si ce serveur est défaillant, commute sur le second serveur. Si le second est défaillant, commute sur le troisième, et ainsi de suite… 27 FRANCAIS 4. Interface WEB 4.2.5. Configuration des sorties Quand vous cliquez sur le bouton Output, la configuration des sorties du LEDI Network IN est affichée ainsi : Ce panneau montre une vue synthétique des sorties du produit. Chaque sortie est pilotée par une carte de sortie. L’affichage est considéré comme une sortie et est pilotée par une carte d’affichage. Un LEDI Network IN peut contenir jusqu’à 4 cartes de sortie en plus de la carte d’affichage. Les cartes de sortie et d’affichage peuvent être contrôlées indépendamment. Dans l’écran montré ci-dessus, chaque rectangle bleu clair sert à contrôler une carte de sortie sur l’afficheur. Quand une carte de sortie est présente, elle peut-être configurée. Si aucune carte n’est présente ou si elle est défaillante, un message est affiché. 28 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 4. Interface WEB Chaque carte de sortie peut-être configurée grâce aux paramètres suivant: ►► Vous pouvez désactiver la carte de sortie. Quand une carte est désactivée, le code horaire n’est plus généré en sortie. Pour désactiver la sortie, cochez la case Deactivate output. ►► Vous pouvez spécifier un fuseau horaire (un décalage) à appliquer sur la sortie de la carte par rapport à l’heure UTC. ►► Vous pouvez spécifier une politque de changement d’heure (DST) à appliquer sur la sortie de la carte par rapport à l’heure UTC. Description & nom de la carte Désactiver la sortie Politique changement d’heure Décalage par rapport à l’heure UTC (fuseau horaire) L’image ci-dessus montre le panneau de configuration pour une carte AFNOR/IRIG-B. De plus, la description contient l’identification et la version du programme incorporé dans la carte de sortie (ici, c’est le programme NTPSAFN1, version 0252). MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 29 FRANCAIS Configuration de la sortie standard 5. Interface SNMP 5.1. Présentation Le LEDI Network IN fournit une interface SNMP v1 pour la surveillance et le diagnostique. Le protocole SNMP permet la supervision d’un appareil par le réseau. Deux types d’informations sont disponibles par l’interface SNMP : ►► Des variables peuvent être lue depuis un superviseur SNMP. Ces variables sont stockées ensemble dans une base de données (MIB) organisée de manière hiérarchique. Les variables sont renseignées par le logiciel NTP pour refléter son état interne. ►► Certains “traps” peuvent être générés par le logiciel NTP pour indiquer une importante modification d’état. Il y a deux parties importantes dans la MIB: ►► Une branche générale appelée System. Cette branche est compatible MIB II. ►► Une branche privée qui contient des informations spécifiques au produit LEDI Network IN. Les MIBs privées sont décrites avec des fichiers .MIB. Deux fichiers .MIB sont fournit sur le CD-ROM dans le répertoire English\LEDINETWORKIN\MIB: ►► Le fichier GtNtpOutBus.mib contient la description des informations concernant la localisation des cartes de sortie dans la MIB: iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).gorgy(8955).hardware(2).ntpOutBus(1) ►► Le fichier GtNtpClient.mib contient la description des informations concernant la localisation du logiciel client NTP dans la MIB: iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).gorgy(8955).software(1).ntpClient(4) 30 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 5. Interface SNMP Software Cette branche contient toutes les informations concernant le logiciel client lui-même. Voici la structure de la branche: Les différents champs de cette branche sont décrit ci-dessous: ►► ntpCliHeader Une courte description du produit. Il est du type GT LEDI Network IN client nnnnnn Vxx.yy (aammjj) où xx.yy est la version courante du logiciel, aammjj est la date d’émission du logiciel (jj/mm/aa) et nnnnnn est le numéro de série du produit. ►► ntpCliProduct Une description du produit avec ses options qui doit être similaire au code produit (décrit dans Annexe D – Guide des codes produits). Par exemple 9257/ AB........ D indique un LEDI Network IN avec des sorties IRIG-B et ASCII et un afficheur (code D). ►► ntpCliVersionNumber Version de ce produit. Il est du type Vxx.yy (aammjj) où xx.yy est la version actuelle du logiciel, aammjj est la date d’émission du logiciel (jj/mm/aa) MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 31 FRANCAIS 5.1.1. Structure de la MIB privée pour le LEDI Network IN ►► ntpCliSerialNumber Numéro de série sur 6 chiffres. ►► ntpCliMAC Adresse matérielle de l’interface Ethernet du LEDI Network IN. Cette adresse est de la forme aa:bb:cc:dd:ee (6 octets binaires). ►► ntpCliMessageString Description du dernier “trap” généré. Ce texte est lié au trap. ►► ntpCliResetInfo Indication sur la raison du dernier redémarrage (reconfiguration ou RAZ manuelle). ►► ntpCliSoftwareState Ce champ donne l’état actuel du logiciel client NTP. Il peut prendre l’une de ces valeurs: ►► Idle: Le produit vient de démarrer. ►► Autodetection: aucun serveur NTP n’a été spécifié et le produit essaye de détecter des serveurs NTP. ►► Autodetectfail: aucun serveur NTP trouvé pour la synchronisation – le produit utilisera un serveur dès que vous en connecterez un sur le réseau. ►► Learning: le logiciel étudie actuellement les propriétés réseau. ►► ntpCliSyncMode Le mode de synchronisation actif actuellement. Il peut prendre les valeurs suivantes : ►► Autodetect: aucun serveur NTP n’a été spécifié et le produit essaye de détecter des serveurs NTP. ►► Sync1server: travaille avec un seul serveur NTP. ►► Sync2server: travaille avec deux serveurs NTP. Quand un serveur est défaillant, il utilise l’autre. ►► Sync3server: travaille avec trois serveurs NTP. Quand un serveur est défaillant, il utilise un des autres serveur. ►► ntpCliSyncSrvTable Ce tableau contient tous les serveurs utilisés pour la synchronisation et d’autres informations. Lma première entrée de la table est le serveur actuellement utilisé pour la synchronisation. La seconde entrée est le second serveur préféré, etc. Chaque entrée est de ce type : ►► ntpCliSyncSrvRank: Rang du serveur. Un serveur de rang est est utilisé pour la synchronisation. ►► ntpCliSyncSrvAddress: Adresse IP du serveur. ►► ntpCliSyncSrvAccuracy: Précision du serveur comme fournit dans la trame NTP (du type 2^-x secondes). 32 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 ►► ntpCliSyncSrvUpAccuracy (Serveur Gorgy Timing seulement) Précision du serveur fournit durant l’étape d’auto-détection. ►► ntpCliSyncSrvUpSrvLoad (Serveur Gorgy Timing seulement) Charge du serveur (nombre moyen de requêtes par secondes) fournit durant l’étape d’auto-détection. ►► ntpCliSyncSrvPrefered (Serveur Gorgy Timing seulement) Un numéro définit par l’utilisateur qui indique le rang de ce serveur. Quand l’auto-détection est activée, le LEDI Network IN utilise le serveur de plus haut rang.10 Hardware La MIB décrit les cartes détectées et leurs configurations. Toutes les cartes de sortie et l’afficheur sont connectés au même bus de sortie. Voici la description des différents champs de cette branche: ►► ntpOutBusCardNumber Nombre de cartes détectées sur le bus de sortie. ►► ntpOutBusCardTable Une table qui montre toutes les cartes détéctées sur le bus de sortie. Chaque carte est indéxéepar son adresse (1…9 pour les cartes de sortie et 9 pour l’afficheur). Chaque entrée est de ce type. 10/ Voir la documentation du serveur NTP que vous utilisez pour configurer la préférence MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 33 FRANCAIS 5. Interface SNMP ►► ntpOutBusCardIndex: Index de cette entrée (adresse de la carte). Cette valeur peut prendre la valeur 1 à 8 pour une carte de sortie et 9 pour l’afficheur. ►► ntpOutBusCardState: L’état de la carte. Il peut être detected pour indiquer que la carte fonctionne correctement, failure si la carte ne répond pas ou scrambled si la réponse de la carte est incorrecte. ►► ntpOutBusCardType: Type de carte (voir Annexe D – Guide des codes produits pour la liste des types de cartes de sortie possible). ►► ntpOutBusCardDescription: Description de la carte. ►► ntpOutBusCardActivation: Indique si la sortie de la carte est activée (activated) ou désactivée (deactivated) : l’activation de la carte peut être controllée par l’interface WEB. Si la carte ne peut être désactivée, ce champs prend la valeur notapplicable.11 ►► ntpOutBusCardTimeZone: Fuseau horaire pour cette sortie. Il est donné comme un offset par rapport au temps universel. Il peut-être changé par l’interface WEB. ►► ntpOutBusCardDayLightSavingPolicy: Indique quelle politique de changement d’heure (DST) est utilisée. S’il n’y a pas de DST, ce champs a la valeur <none>. Cette politique peut être changée via l’interface WEB. ►► ntpOutBusCardDayLighSavingCurrent: Indique si la politique de changement d”heure (DST) est en fonctionnement (valeur summertime) ou pas (valeur wintertime). Si le DST n’est pas activé, ce champs, ce chanmps a la valeur notapplicable. ►► ntpOutBusCardTotalOffset: Indique le décalage total actuel par rapport à l’heure universelle UTC. Voici un exemple de la description de la carte de sortie affichée dans un navigateur SNMP: 11/ L’afficheur ne peut être désactivé par exemple 34 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 Annexe A – Connexions Cette annexe contient une description des différents connecteurs du LEDI Network IN. Toutes les prises sont localisées à l’arrière du produit. Actuellement, seuls deux types de sorties sont disponibles. 1. Connexion pour tous les produits 1.1. Produits 230V et 115V AC (type ‘0’) L’arrière du produit possède une prise d’alimentation standard, une prise Ethernet RJ45 et un bouton RESET comme ci-dessous: 1.2. 18/72V DC product (type ‘9’) Le connecteur Ethernet et le bouton RESET sont identiques. Seul le connecteur d’alimentation diffère. +V DC 0V MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 35 FRANCAIS 6 2. Sortie pour carte type ‘B’ (sortie double AFNOR/IRIG-B NFS87500) Cette carte a sa sortie sur une simple prise 4 points. Le code AFNOR est disponible en double sur cette sortie. Voici une vue schématique de la carte de sortie AFNOR/IRIG-B: TOP Code horaire AFNOR/IRIG-B sortie 1 Modulateur d’amplitude AFNOR/IRIG-B sortie 2 Le connecteur de sortie est localisé sur la face arrière du rack comme ci-dessous: Voici les pattes du connecteur (le même signal est généré sur les sorties ½ et ¾): Sortie 1 1 36 Downloaded from www.Manualslib.com manuals search engine 2 Sortie 2 3 4 MDE-LEDI-NETWORK-IN-4065V1.0 6 Annexe A – Connexions Cette carte possède une prise 4 points et un connecteur DB9 La prise 4 points sort le TOP de deux manières différentes et la prise DB9 fournit la trame horaire en sortie en niveau RS-232 ou RS-485. Voici une vue schématique de la sortie ASCII+TOP: Sortie collecteur ouvert TOP Code d’horaire VCC Driver Sortie relais statique Driver de ligne RS-232 Driver de ligne RS-485 TXD TX+ TX- Sortie RS-232 Sortie RS-485 Les connecteurs de sortie sont sur la face arrière du rack comme ci-dessous: La prise 4 points a le format suivant : Sortie relais statique 1 MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 2 Sortie collecteur ouvert 3 4 37 FRANCAIS 3. Sortie pour carte type ‘A’ (ASCII+TOP) Le connecteur DB9 a le format suivant: GND 5 4 9 TXD TX+ 2 1 3 8 7 6 TX- 38 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 Cette annexe contient une description du code horaire utilisé pour les différentes sorties. 1. Carte Type ‘A’ (sortie ASCII+TOP) Voici la configuration par défaut : ►► La pulsation PPS est générée toutes les 30 secondes et dure 1 seconde. ►► La trame ASCII est générée au même moment que le PPS. Cette trame contient 23 caractères avec le format suivant : STX D A Y D D / M M / Y Y H H : M M : S S CR Voici une description des différents champs de la trame : Field Size Value/Meaning STX 1 Un simple octet de valeur 2, qui signale le début de la trame. DAY 3 Le jour de la semaine en anglais (MON pour Lundi, TUE pour Mardi, WED pour Mercredi, THU pour Jeudi, FRI pour Vendredi, SAT pour samedi, SUN pour Dimanche) DD 2 Jour du mois en 2 caractères ASCII (01-31) MM 2 Mois dans l’année en 2 caractères ASCII (01-12) YY 2 Année en 2 caractères ASCII (00 for 2000 – 99 for 2099) HH 2 Heure en 2 caractères ASCII (00 to 23) MM 2 Minutes en 2 caractères ASCII (00 to 59) SS 2 Secondes en 2 caractères ASCII (00 to 59) CR 1 Un simple octet de valeur décimale 13, qui signale la fin de la trame MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 39 FRANCAIS Annexe B – Format du code de sortie 2. Carte type ‘B’ (AFNOR/IRIG-B NFS87500) 2.1. Format de la trame 40 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 Annexe B – Format du code de sortie FRANCAIS 2.2. Encodage des bits MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 41 Annexe C – Caractéristiques 1. Dimensions Le rack est au format standard 19” 1U rack. Voici ses dimensions: 424 mm 1U = 44 mm 263 mm 482 mm 2. Spécifications électriques 230 V AC Maximum: 0,1 A max. Typique : 20 mA plus 2mA par sortie 115V AC Maximum : 0,2 A max. Typique : 40 mA plus 4mA par sortie 18-72V DC Maximum : 0,6-0,15 A max. Typique : 250mA plus 25 mA par sortie (18V) 62mA plus 7 mA par sortie (72V) Consommation électrique Environnement Température de fonctionnement : 5 à 50°C (41 à 122°F) Température de stockage : -40 à 70°C (-40 à 151°F) Autonomie électrique 4 heures sur les batteries internes 3. Autres spécifications Protocoles supportés ARP,UDP,TCP,Telnet,ICMP,SNMP,DHCP,TFTP, HTTP,ENDMI, AutoIP, JAVA, SNTP client Interface réseau 10Base-T avec interface RJ-45 Management SNMP, serveur WEB, Telnet, ENDMI Mise à jour Possible par le serveur TFTP Mémoire ROM:512K, RAM:128K, EEPROM:2K 42 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 Annexe D – Guide des codes produits FRANCAIS 1. Localisation de l’étiquette L’étiquette qui identifie le produit se situe sur le dessus ou la face arrière du produit. 2. Informations de l’étiquette L’étiquette contient les informations suivantes: GORGY TIMING CODE 9257/Xopt N° SERIE nnnnnn La troisième ligne contient le numéro de série sur 6 chiffres (nnnnnn). La seconde ligne est la description du produit: 9257/ X opt Une ou plusieurs lettres (une lettre par sortie): A ASCII+TOP B IRIG-B/AFNOR NFS87500 Une lettre qui indique le type d’alimentation: 9 Pour courant continu 18 à 72V 0 Pour courant alternatif 230V 50Hz Identification du produit LEDI Network IN Par exemple, le code 9257/9AB identifie un LEDI Network IN avec une alimentation courant continu 18/72V et deux sorties. La première sortie utilise le protocole ASCII, la secondeest une sortie IRIG-B/AFNOR. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 43 Annexe E – Documents complémentaires Cette annexe contient quelques documents utiles pour gérer un ensemble de produits GT dans vote installation. Chaque document est une table que vous pouvez librement copier et distribuer: ►► Description de l’installation: vous pouvez utiliser cette table pour créer une vue synthétique de toute votre installation. ►► Configuration de l’appareil : vous pouvez utiliser cette table pour enregistrer la configuration des sorties et afficheur de chaque produit. 44 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 Annexe E – Documents complémentaires Vue résumée de l’installation FRANCAIS Description de l’installation Date d’installation Nom de l’installateur Description du produit MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine Numéro de série Localisation 45 Annexe E – Documents complémentaires Configuration des appareils Description de l’installation Date d’installation Nom de l’installateur Appareil 46 Downloaded from www.Manualslib.com manuals search engine Sortie Fuseau horaire et politique de changement d’heure MDE-LEDI-NETWORK-IN-4065V1.0 FRANCAIS NOTES MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 47 5. Option chronomètre GORGY TIMING SAS Quartier Beauregard 38350 La Mure d'Isère (Grenoble France) Phone: +33 4 76 30 48 20 Fax: +33 4 76 30 85 33 email: [email protected] - www.gorgy-timing.com SUPPORT TECHNIQUE depuis la France sur un poste fixe : [email protected] RADIO TIMING®, LEDI ®, LEDI CA®, HANDI ® sont des marques déposées GORGY TIMING. Numéro de déclaration d’activité de prestataire de formation : 82 38 04877 38 GORGY TIMING RC 74 B 38 - Toutes modifications d'ordre technique ou esthétique peuvent être apportées sans préavis. 48 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 LEDI® Network in MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 49 ENGLISH USER GUIDE Important safety instructions WARNING! Read the section that follows very carefully before installing your equipment. It gives the safety instructions to follow during installation. The electrical installation to which the equipment is connected must comply with the NF C 15-100 standard. This device does not have a primary power switch. A power protection system (circuit-breaker or disconnecting switch), that is easy to access must be built into the wiring installation. This device must support the nominal voltage and current values specified on the clock. In Europe: to comply with European regulations on the protection of persons and the environment, you must dispose of this equipment in a collection site provided for this purpose (separately from household waste). Contact your reseller, collection site or the competent lcoal authorities for more information. Toute modification ou ouverture du produit sans l’accord du SAV entraîne la perte de la garantie. All maintenance operation shall be conducted with power shut off, including systems connected on relay outputs if any. Generally, the power cable (220V) and transmission cable (of time signal) shall not be very close to each other, so as to avoid interference (keep the distance of a few centimeters). Gorgy Timing disclaims all responsibility in case of accident or damage caused by an improper use of the product. GORGY TIMING products are compliant with the following standards: CE, EN 60950, EN 55022, EN 50024 50 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 contents 1.1. Quick installation................................................................................................................. 53 1.1.1. Check the package content..................................................................................... 53 1.1.2. Connect the product................................................................................................ 54 1.2. Set-up your product............................................................................................................. 54 2.1.1. Manual network configuration.................................................................................. 54 2.1.2. Output cards configuration...................................................................................... 55 1.3. Basics.................................................................................................................................. 55 1.3.1. Synchronization concepts........................................................................................ 55 A/ Clock Correction principles...................................................................................... 55 B/ Network dialog......................................................................................................... 57 C/ Working with several servers.................................................................................. 57 1.3.2. The NTP client software.......................................................................................... 58 2. FULL SETUP................................................................................................................ 59 2.1. Network configuration.......................................................................................................... 59 2.1.1. Default configuration................................................................................................ 59 2.1.2. Changing network parameters................................................................................ 59 2.1.3. Integration in your network...................................................................................... 61 2.2. Output cards configuration ................................................................................................. 62 2.2.1. Introduction.............................................................................................................. 62 2.2.2. Default configuration................................................................................................ 62 2.2.3. Change the settings................................................................................................. 62 3. FRONT DISPLAY INTERFACE..................................................................................... 64 3.1. Start-up conditions............................................................................................................... 64 3.2. Time display......................................................................................................................... 65 3.3. Alarm condition.................................................................................................................... 66 4. WEB INTERFACE......................................................................................................... 67 4.1. Presentation........................................................................................................................ 67 4.2. Description of the WEB interface......................................................................................... 68 4.2.1. Ecran Principal........................................................................................................ 68 4.2.2. Standard setup........................................................................................................ 69 4.2.3. SNMP setup ........................................................................................................... 72 4.2.4. NTP Setup............................................................................................................... 74 4.2.5. Output and display setup......................................................................................... 76 4.3. WEB interface of NTP server output card........................................................................... 79 4.3.1. Network and SNMP setup Status bar...................................................................... 79 4.3.2 NTP setup Description.............................................................................................. 80 5. SNMP INTERFACE....................................................................................................... 82 5.1. Presentation........................................................................................................................ 82 5.1.1. Structure of the private MIB for LEDI Network IN.................................................... 83 5.1.2. Description of the SNMP traps................................................................................ 87 5.2. SNMP interface for NTP server card................................................................................... 88 5.2.1. Software information MIB for the NTP server outcard............................................. 88 5.2.2. Description of the SNMP traps................................................................................ 92 MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 51 ENGLISH 1. inTRODUCtion........................................................................................................... 53 APPENDIX A – CONNECTIONS...................................................................................... 93 1. Connection for all products..................................................................................................... 93 1.1. 230V and 115V AC product (type ‘0’)......................................................................... 93 1.2. 18/72V DC product (type ‘9’)...................................................................................... 93 2. Dual AFNOR/IRIG-B NFS87500 output (‘B’ type).................................................................. 94 3. Dual AFNOR/IRIG-B NFS87500 DCLS RS422 and TTL output (‘T’ type).............................. 95 4. RS232 and 485/422 ASCII+TOP (‘A’ and ‘R’ type)................................................................. 96 5. TOP / ALARM output (‘A’, ‘R’ type and ‘G’ type) .................................................................... 97 5.1. Pin-out........................................................................................................................ 97 5.2. Examples of how to use the open collector output (pins 3-4)..................................... 98 5.3. Example of how to use the static relay output (pins 1-2)............................................ 99 APPENDIX B – OUTPUT CODE FORMAT.................................................................... 100 1. ‘A’ and ‘R’ type cards (ASCII+TOP output)........................................................................... 100 2. ‘B’ and ‘T’ type cards (AFNOR/IRIG-B NFS87500).............................................................. 101 2.1. Frame format............................................................................................................ 101 2.2. Bit encoding.............................................................................................................. 102 3. DCF and TDF time code description.................................................................................... 103 APPENDIX C – TROUBLESHOOTING.......................................................................... 104 I made a « Scan now ! » with GTNetManager.......................................................................... 104 but I cannot see the device ?.................................................................................................... 104 I cannot open the configuration WEB page ?........................................................................... 104 An output is not visible in the configuration WEB page ?......................................................... 105 The device stay in “Commuting” mode ?.................................................................................. 105 APPENDIX D – MAINTENANCE.................................................................................... 106 1. Procedure to follow to change the battery............................................................................ 106 2. Output card switchs verification............................................................................................ 107 3. Updating Firmware............................................................................................................... 107 3.1. Obtaining Firmware.................................................................................................. 107 3.2. Reloading Firmware................................................................................................. 108 APPENDIX E – DATA......................................................................................................110 1. Measurements...................................................................................................................... 110 2. Specifications....................................................................................................................... 110 3. Autres spécifications............................................................................................................. 110 3. Stamp contents......................................................................................................................111 APPENDIX F – ADDITIONAL DOCUMENTS..................................................................112 52 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 1. inTRODUCtion This document is a user’s guide for the LEDI Network IN. This product is a NTP client. The purpose of this device is to synchronize various equipments using a reference time from one or several NTP servers. You can see this product as a kind of converter that translates a “NTP signal” to a traditional synchronization signals (ASCII+TOP, AFNOR, IRIG-B for example). ►► You can use the installed network architecture with the well-known protocols Ethernet+TCP/IP ►► L’installation est simple. ►► You can change Simplified set-up. ►► The product is a 19” 1U rack that can be easily installed on your installation. EBy using a Gorgy Timing server in combination with the LEDI Network IN you greatly improve the ease of installation and use. ☛☛Jump directly to section 1.1 for quick installation 1.1. Quick installation This part contains the minimum information for the set-up of the LEDI Network IN. You can find additional information in part 3. 1.1.1. Check the package content The package must contains the following items: ►► The product itself: a 19” 1U rack. • The name of this product is LEDI NETWORK IN which is written on the front side of the rack. • The code and configuration of the product can be checked on the identification stamp put on top or backside of the product. It must be 9257/opt (where opt depends on the output cards – see Erreur ! Source du renvoi introuvable.).. ►► A power supply cable (only for 220V AC and 115V AC versions). ►► A network cable ►► A CDROM that contains set-up and management tools. ☛☛Contact your dealer if one of the items above isn’t in the package. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 53 ENGLISH Using the LEDI Network IN for synchronization provides you with several advantages: 1.1.2. Connect the product ►► It is highly recommended that you notice the serial number (written on identification stamp), the localization and a short description for the product. The table in You can use the table in Appendix F – Additional documents ►► Connect the synchronization outputs to your equipment (see Appendix A – Connections for more information). ►► Connect the LEDI Network IN to your network using the network cable. ►► Connect the LEDI Network IN to a power supply using the power supply cable when it is present. Your system should work immediately if you use Gorgy Timing NTP server(s) and there is a DHCP server on your network. After a 2 minutes learning stage, the LEDI Network IN activates its outputs and begin to delivers UTC time. However, Gorgy Timing recommends you to fill-in for each product its physical localization. This is possible using the GTNetMng tool localized on the CD-ROM. For more information, see part 31.2. 1.2. Set-up your product 2.1.1. Manual network configuration Gorgy Timing NTP products are configured in factory to automatically get an IP address. Two mechanisms are used: 1. If a DHCP server is present on your network, our products get an address automatically. This ensures that the IP address is compatible with your network. 2. If no DHCP server is present, the product automatically takes an IP address using the AutoIP mechanism. In this case, the address is in the range 169.254.x.y (where x and y are in the 0…255 range).If both server and client have started in this mode, they should work correctly together but their IP addresses may be incompatible with other devices on the network.1 1/ For example, you may not have the possibility to configure the LEDI Network IN from a WEB navigator 54 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 1. inTRODUCtion The default DHCP identifier is CRnnnnnn (nnnnnn is the serial number of the product).22 You can change this identifier with the GTNetMng tool or through the WEB interface as described in part 31.2 and 52.2 If you don’t have a DHCP server or you want to configure yourself the network parameters, use the GTNetMng tool on the CDROM to change the network parameter. Please refer to part 31.2 for more information. ☛☛Don’t hesitate to contact your network administrator for the ENGLISH configuration of the LEDI Network IN. He can help you to optimize your network installation. 2.1.2. Output cards configuration The default configuration for all the output cards is to deliver UTC time. The time received from the NTP server is directly sent to the output. Each card can be configured to output several local times. This configuration is done through a WEB browser (see part 32). 1.3. Basics This part contains a description of the basic concepts of the product LEDI Network IN. It helps you to understand the behavior of the product under various circumstances. The NTP client software is the very heart of the LEDI Network IN. It performs all the synchronization, the management of the hardware and provides information for the WEB interface and the SNMP protocol. 1.3.1. Synchronization concepts A/ Clock Correction principles The objective of the synchronization is to make two clocks indicating the same time. In the case of NTP based synchronization, the LEDI Network IN clock must indicate the same time that the NTP server clock. 2/ Some DHCP servers have the ability to copy the DHCP name into the DNS. In this case, you can access the LEDI Network IN directly by its DHCP name instead of its IP address. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 55 Heure serveur Dérive nulle Heure client Heure serveur Heure client To perform this synchronization, the NTP client software permanently compares the two clocks and computes Evolution dans le tempsthe following information: ►► Offset: It’s the difference between the time of the server clock and the time of the client clock. For example, if the server clock indicates 2:10:13 and the client clock indicates 2:11:14, the offset is –1:01.Heure serveur ►►Dérive Drift: constante Heure serveur It’s the frequency difference between the two clocks. When drift is not null and Heure client without clock correction, the offset between the two clock increase or decrease Heure client depending on the drift sign.3 The following figure shows how the evolution of the two clocks with or without drift: server time Drift is null : client time server time client time Evolution during time server time server time Drift is constant : client time client time The objective of the synchronization of a NTP client to a NTP server is to reduce as much as possible the drift and the offset. The accuracy and stability of the client clock is tightly coupled to the efficiency of the reduction process. 3/ There are several reasons for the presence of a drift between two clocks: generally the drift is due to the temperature difference between the two clocks. 56 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 1. inTRODUCtion B/ Network dialog The real drift and offset of the LEDI Network IN clock related to the NTP server are estimated from a measured offset. This offset is computed by subtracting the client clock date from the server clock date. client side Network server side Query server date Return current server date Receive reply date On a LAN, it takes some milliseconds between the time when the client asks for the date and the time when it receives the reply. This time is due to transmission delay on the network. It can vary because of network load or NTP server load. Worse, the transmission time from client to server is generally not the same that the one from the server to client. Actually, on a large period of time, the difference of sum of client-server and server-client transmission delays is zero. The NTP client algorithm implemented in the LEDI Network IN is designed to compensate transmission delay and to average the measures. C/ Working with several servers The NTP client software has the ability to work with several NTP servers (up to 3 servers). When not enough reply is received from a server or this server doesn’t reply or reply too slowly, the NTP client software uses an other one. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 57 ENGLISH Periodically, the client estimate current offset from the server. This measure is done using a message-passing mechanism as shown on following figure: 1. inTRODUCtion 1.3.2. The NTP client software NTP software states Here are the different states of the NTP client software: Searching servers Starng Auto-detecon Learning environment Learning environment Learning Enable outputs No reply Tracking Commung Commuta�on OK Here is a description of these states: ►► Starting: The software is starting, it initializes and check the hardware if needed. ►► Auto-detection: Server auto-detection is activated. The NTP client tries to find Gorgy Timing servers. At least one detected server is required to leave this state; ►► Learning: The NTP client software has found one or several Gorgy Timing (auto-detection activated) or works with configured servers. In this state, the software learns network properties. About 2 minutes are required to complete this stage; ►► Tracking: Normal behavior, the NTP client permanently evaluate its offset and drift with the server; ►► Commuting: Not enough reply received from current server, trying another server. 58 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 2. FULL SETUP This part contains information for a full configuration of the product. It should be used for fine network configuration and output cards set-up 2.1. Network configuration The LEDI Network IN is configured to automatically take an IP address from a DHCP server. At startup, the product broadcast a DHCP query to get an IP address. This query contains a DHCP name. There are two cases: ►► If a DHCP server is installed on the network, it record the DHCP name and return an IP address. The LEDI Network IN starts working with this address. ►► If no DHCP server is installed, the LEDI Network IN automatically uses a default IP address in the range 169.254.x.y (where x and y are between 0 and 255). The default DHCP identifier of the product is CRnnnnnn with nnnnnn, the serial number on 6 digits. The serial number is written on the identification stamp on the top or on the bottom of the product. The default SNMP name of the product (that can be seen from a SNMP browser (see part 6) or from a WEB browser) is LediNetwkINnnnnnn with nnnnnn, the serial number on 6 digits. 2.1.2. Changing network parameters Use the GTNetMng tool provided on the CDROM to configure your device: ►► Insert the CDROM in the drive. Start the GTNetMng tool that is localized in the directory Common\Configuration44 4/ For example, if your CD reader has letter E:, the GTNetMng tool is localized in E:\Common\Configuration\ GTNetMng.exe MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 59 ENGLISH 2.1.1. Default configuration ►► The GTNetMng tool displays automatically the Gorgy Timing products installed on your network. Each line contains information about one connected product as shown below: Name, serial number and localization Current Ip address network mask MaC address DHCp identifier ►► Double-click on the line related to the product you want to configure. The following panel is displayed: Name of the device (GT LEDI Network IN) Serial number (040204) Localization (Test Line) Ethernet (MAC) address of the device Localization of the product ►► Set the network parameters and physical localization and click the Set! button. 60 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 2. FULL SETUP 2.1.3. Integration in your network You don’t have to change any network setting for the following cases: ►► You have a DHCP server and enough reserved IP address for the product. Some DHCP servers have the capacity to register the device in the DNS. In this case, the registered name is the DHCP identifier. Then, you can access to the device from your WEB or SNMP browser. For example if you give the DHCP name ntpin3 to your LEDI Network IN, you can simply type ntpin3 in the address field of your WEB browser. If you have several products to install on your installation, it is highly recommended to follow the following steps: ►► Use the document provided in Appendix F – Additional documents (Summarized installation view) and note the serial number and physical localization of each product during the installation and connection; ►► On a PC connected on the same network that the products and start GTNetMng. All the GT products should appears with their serial number. Set the network parameter and localization using the document filled at previous step. ►► You can keep this document for further reference. ☛☛You can found the summarized installation view document in a WORD format on the CD ROM. Its full path is English\LEDI Network IN\docs\ installation.doc. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 61 ENGLISH ►► You don’t have a DHCP server but you don’t need to access to the device through its WEB or SNMP interface. In this case, the AutoIP mechanism will automatically affect an IP address but this address will probably be incompatible with your network. 2.2. Output cards configuration 2.2.1. Introduction Your LEDI Network IN is provided with up to 4 output cards. Each output card is tightly synchronized on the NTP time code received from the NTP server. Each card acts as a kind of translator that receives time from the NTP software and output specific time code. Currently, there are 6 kinds of cards: ►► ASCII+TOP RS232 (‘A’ type card) ►► ASCII+TOP RS485 (‘R’ type card). ►► AFNOR NFS 87500 / IRIGB (‘B’ type card). ►► AFNOR /IRIGB TTL / RS422 (‘T’ type card). ►► ALARM (‘G’ type card). ►► NTP server (‘N’ type card). You can freely use and copy the table Devices configuration in Appendix F – Additional documents. 2.2.2. Default configuration When you receive this product from Gorgy Timing, all the output cards are configured to output UTC time and time is constant all along the year (no Day Saving Time correction). The display is managed as an output cards and can be configured in the same way.. 2.2.3. Change the settings Open the WEB site of the LEDI Network IN (see part 5). Click on the button. The current configuration of your product appears at the screen (shown below for a 9257/ A model): 62 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 ENGLISH 2. FULL SETUP In this screen you can tune each card independently (see part 5.2.5). When you have change.the settings, click on the . button. The modification should appear immediately at the outputs or on the display. 2.2.4. NTP server output card configuration You can add a NTP server output card to your LEDI network IN. By this way, you can synchronize your local network on this card, which is itself synchronized by the NTP client on a remote Internet NTP server. The NTP server card has to be configured by the same way than the NTP client of the LEDI Network IN. Its default network configuration is DHCP mode with identifier SCnnnnnn with nnnnnn, the serial number on 6 digits. The default SNMP name of the NTP server (that can be seen from a SNMP browser or from a WEB browser) is NTPServnnnnnn with nnnnnn, the serial number on 6 digits. To change the network parameters of the NTP server card, use the GTNetMng tool : see page 10). Like the NTP client, the NTP server card provides a WEB page for fine configuration (see page 31) and a SNMP MIB for supervision through the network (see page 40). MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 63 3. FRONT DISPLAY INTERFACE The front display interface can display up to 16 characters. Two buttons provides you with display configuration and global reset. The LEDI Network IN uses the front display to show current time and different alarm condition. Reset the LeDI Network Enhanced Switch between UTC and LOCaL time display 3.1. Start-up conditions During start-up, the time and date of the LEDI Network IN are not valid and are not displayed. Then, you can see the following texts: ►► When the device start, all the dots of the displays are lightened. ►► During hardware initialization, the following text is displayed. ►► If no server is configured by the user, the LEDI Network IN try to detect GT servers and display the following message: ►► If the auto detection stage fails, the following text is displayed until a GT server is available on the network: 64 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 3. FRONT DISPLAY INTERFACE ENGLISH ►► If there is at least one GT server or the user has configured manually the servers, the LEDI Network IN enters learning stage and displays the following text: 3.2. Time display When no alarm is present and the LEDI Network IN is correctly synchronized on a server, the current time of the server is permanently displayed. The display alternatively shows time and date as shown below: ►► When displayed is configured to display UTC time, the following information are alternatively displayed: ►► When displayed is configured to display local time, the following information are alternatively displayed: MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 65 3. FRONT DISPLAY INTERFACE 3.3. Alarm condition The commuting alarm indicates that the server currently used for synchronization does not reply (or does not reply correctly). In this case, the LEDI Network IN tries another server. The display alternatively shows time (as described in previous part) and the following text: 66 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 4. WEB INTERFACE 4.1. Presentation The LEDI Network IN can be configured and supervised through a WEB interface. This interface provides you with the following features: ►► Management of network parameters ►► Management and diagnostic of NTP client software itself ►► Management and diagnostic of output cards. Each LEDI Network IN has its own WEB server that delivers WEB pages. The WEB site is a JAVA applet; if needed, you can find a JVM on the CDROM in the directory Common\ JAVA. To access the WEB site, type-in the address of the LEDI Network IN in the address field of your WEB browser (as shown below) and validate the input5. It takes about 20 seconds to load of the JAVA applet. If the load fails, it can be for one of the following reasons: 1.The IP address is invalid; 2.A network problem6 prevent your computer to contact the LEDI Network IN; 3.You don’t have a JVM engine installed on your computer. For the first two reasons, you have to check for the IP address of the LEDI Network IN and your network configuration. For the last reason, you have to install the JVM (see directory Common\JAVA on the CDROM). 5/ If you have configured your LEDI Network IN in DHCP mode and that your server automatically register DHCP name in the DNS, you can also use the DHCP name instead of the IP address 6/ Check especially the configuration of your Internet Explorer. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 67 ENGLISH ►► Management of SNMP parameters 4.2. Description of the WEB interface 4.2.1. Ecran Principal This is the screen that appears when accessing the WEB site of the LEDI Network IN. The first four buttons at the left of the screen provide an access to the following panels: 1. Standard: information about the product and configuration of network parameters See part 2.2. 2. SNMP: configuration of SNMP parameters; 3. NTP: diagnostic and configuration of the NTP software behavior; 4. Output: diagnostic and configuration of output cards and display. The Set Up! button updates immediately the LEDI Network IN configuration. The configuration is stored permanently in an EEPROM. WARNING. Some parameters cannot be modified without restarting the LEDI Network IN. If you change these kind of parameters and click on the Set Up! button, the LEDI Network IN restarts with the new parameters and needs 2 minutes before re-enable its outputs. 68 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 4. WEB Interface 4.2.2. Standard setup ENGLISH When you click the Standard button, the network parameters and product information are displayed as shown below: In the top of the panel, you can control the network parameters and the WEB access password. In the bottom of the panel, you have information about the product. Network parameters WARNING. If you click on the Set Up! button after changing one or several network parameter(s), the LEDI Network IN must restart to use the network parameters. During the reset and 2 minutes after, the output(s) of the product is(are) disabled. Here are the different parameters: ►► IP mode Indicate if the LEDI Network IN works with a fixed IP (set in the field IP address) or use DHCP protocol (the DHCP identifier is set in the field DHCP identifier); MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 69 ►► IP address Indicate the network address affected to the device. An IP address is made of four numbers separated by a dot. Each number range from 0 to 255; ►► DHCP identifier Identifier to be used when the LEDI Network IN is configured in DHCP mode. This identifier has 8 letters maximum. The default value is CRnnnnnn (where nnnnnn is the serial number on 6 digits); ►► Network submask Indicate the width of the network you use. For example, a network submask 255.255.255.0 indicates that only the last number change (in the example above, address in the network can change between 192.168.10.1 to 192.168.10.254)7. ►► Gateway address If you want the LEDI Network IN to communicate with devices outside the local network, you must indicate a gateway that will be used to go outside local network; ►► Without gateway Check this box when you don’t have a gateway on your network (or don’t want to use it); Product information Here is a description of the product information area: ►► Hardware GT serial number Display the Gorgy Timing serial number of the product. This is a 6 digits number which is the same than the one stamped on the bottom or background of the rack ►► Hardware Product code Display the Gorgy Timing base code of the product without option (9257 for a LEDI Network IN) ►► Ethernet Interface (MAC) Address Indicate the Medium Access address of the Ethernet interface of the LEDI Network IN ►► Ethernet Interface Adapter Serial number Indicate the serial number of the Ethernet interface of the LEDI Network IN. This information can be useful for maintenance; ►► Firmware Description Short text that describes which software is running on your product 7/ If you configure several devices to communicate on the same network, you must have the same network submask. 70 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 4. WEB Interface ►► Firmware Version/Release Date Version of the software running in the LEDI Network IN and date of the last produced software (in English format yymmdd for example 021010 for 2002, October the 10th); ►► Last reboot reason A text that Indicates why the LEDI Network IN has restarted the last time. If you want to protect access to the parameters of the LEDI Network IN, you can specify a password. This is done by enter the password twice in the area Enter password and Confirm password (the same password in the two areas). If you don’t want to protect the parameters, check the box Without password. When a password is set, it will be asked to the user at the next connection. In this case, the main screen looks like follows: Status bar The status bar is positioned on bottom of the WEB page. It gives information about the NTP client software. It contains the following information: Current UTC time received from NTP MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine Current state of NTP software Current state of remote NTP server synchronization 71 ENGLISH WEB site access protection 4.2.3. SNMP setup When you click the SNMP button, the SNMP parameters are displayed as shown below: The very standardized SNMP protocol provides a means to get information and alarms from the LEDI Network IN.8 Access to these information (the MIB) can be “protected” by a keyword that is the Community Name. Alarms are sent to a SNMP browser localized on a computer identified by its IP address. Up to 5 IP Trap address can be specified that allows the alarm monitoring from 5 different computers. Last, the SNMP related name, location and contact could be configured in this screen. These information are stored in the system branch of the MIB and can be displayed in a SNMP browser or in the GTNetMng tool (see part 31.2). For convenience, alarms can be notified through the SYSLOG protocol that is more often implemented under UNIX®. 8/ See part 6 for more information about SNMP 72 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 4. WEB Interface Description Here is a description of the fields in this panel: ►► SYSLOG address #1...#2 Address(es) of the computer to which will be sent the SYSLOG alarm notification. When you don’t use an address, you must check the related No box; ►► SYSLOG File Id Identify the file to use on remote computer for SYSLOG protocol; ►► Community name A simple keyword that is needed in a SNMP browser to access SNMP information. This keyword must have 8 letter at the most; ►► System name A text that you can use to give a name to the LEDI Network IN. This name appears in the sysName variable of the system branch of the MIB. The initial value is LediNetwkINnnnnnn (where nnnnnn is the serial number of the product); ►► System location A text that you can use to indicate the physical localization of the LEDI Network IN. This name appears in the sysLocation variable of the system branch in the MIB. There is no initial value. ►► System contact A text that you can use to indicate the person to contact for any problem related to this LEDI Network IN. This name appears in the sysContact variable of the system branch in the MIB. There is no initial value. dentifie le fichier à utiliser sur l’ordinateur distant pour le protocole SYSLOG. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 73 ENGLISH ►► Trap address #1...#5 Address(es) of the computer(s) to which will be sent the SNMP alarm notification. When you don’t use an address, you must check the related No box; 4.2.4. NTP Setup When you click the NTP button, the configuration of the synchronization of the LEDI Network IN is displayed as shown below: The LEDI Network IN can be synchronized on up to three NTP servers. In fact, the NTP software uses only one server at the same time but can commute to another server when there is no or not enough reply. The NTP configuration panel shows what is the synchronization mode used by the server or selected by the NTP software. It also shows the servers defined by the user or detected by the software Description The right part of this screen shows the current configuration used by the NTP client software: IIt shows the different servers used for synchronization and the current synchronization mode (on the screenshot above, there is only one server at IP address 192.168.10.124). In addition, this screen part shows what is the server currently used for synchronization (with a frame labeled Active). If a commutation is in progress, the label Trying is displayed nears the related NTP server. : 74 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 4. WEB Interface If you select the checkbox Auto-detection, the LEDI Network IN try to use the GT NTP servers present on your network and use the more appropriate synchronization mode. If you don’t select the checkbox Auto-detection, you have to indicate the synchronization mode and the NTP servers to use. The following table can help you to select the more appropriate parameters: Mode # of NTP servers used One server 1 Use only one server for synchronization Two servers 2 Use the first server at startup. If this server fails, commute to the second server. If this server fails, commute to the first one and so on… Three servers 3 Use the first server at startup. If this server fails, commute to the second server. If this server fails, commute to the third one and so on… MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine Description 75 ENGLISH The left part of the NTP screen allows you to configure the synchronization mode and the NTP servers used: 4.2.5. Output and display setup When you click on the Output button, the configuration of the output of the LEDI Network IN is displayed as shown below: This panel shows a synthetic view of the outputs of the product. The display is considered as an output and is driven by a display card. A LEDI Network IN can contain up to 4 output cards plus the display card. The display and each output cards can be configured independently using the right cyan box. When an output card is not present or in failure, its box doesn’t appear. At this time, there are 6 kinds of output cards: • ASCII+TOP RS232 (‘A’ type card). • ASCII+TOP RS485 (‘R’ type card). • AFNOR NFS 87500 / IRIGB (‘B’ type card). • AFNOR /IRIGB TTL / RS422 (‘T’ type card). • ALARM (‘G’ type card); • NTP server (‘N’ type card). You can freely use and copy the table Devices configuration in Appendix F – Additional documents. 76 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 4. WEB Interface Standard output configuration Description & name of the card Disable the output ENGLISH DST policy Offset to apply to UTC time The previous picture shows the configuration panel for an AFNOR/IRIG-B. In addition, the description contains identification and version of the program embedded in the output card (there, it’s the program NTPSAFN1, version 0252). Each output card can be configured independently through the following parameters : ►► Output deactivation Except the display, all the output cards can be deactivated. The deactivation has the following effects : ►► For ASCII+TOP card, the time frame is not generated and the TOP outputs are in the open state; ►► For AFNOR output, the carrier is not modulated. ►► The ALARM output doesn’t generate warning signal. ►► Time Zone The “Time Zone” is a time offset that can be added or subtracted from the time received through the NTP protocol (which is UTC time) to generate local time. For example in France, local time is GMT + 1:00. ►► Day Saving Time In addition to the Time Zone, many countries apply a Day Saving Time correction. The year is made of two areas: in summer time, 1 hour more is added to the time (after Time Zone correction), in winter time only the Time zone correction is applied. Don’t forget to select the appropriate country in the WEB interface. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 77 Here are the different DST policies : European Union Start: Last Sunday in March at 1 am UTC End: Last Sunday in October at 1 am UTC USA / Canada / Mexico / St. Johns / Bahamas / Turks / Caicos tart: First Sunday in April End: Last Sunday in October Australia – Standard Start: Last Sunday in October End: Last Sunday in March Russia Start: Last Sunday in March at 2 am local time End: Last Sunday in October at 2 am local time Fine output configuration Some output cards provide specific configuration : ►► ASCII + PPS fine configuration : You can configure here the period and the width of the TOP. ►► AFNOR / IRIG-B fine configuration : Choose your frame format : Afnor, Irig-B or Irig-B + binary second. ►► ALARM fine configuration : To configure the different alarm signals, choose an alarm type (no alarm, synchronization failure, power failure, synchronization + power failure) then set the period and width of the signal. Do the same for each alarm type. 78 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 4. WEB Interface NTP server output configuration Offset from UTC cannot be configured, as the card deliver NTP time code in UTC. To configure finely the NTP server card, you need to open its own WEB page, described in the following chapter. 4.3. WEB interface of NTP server output card 4.3.1. Network and SNMP setup To configure network and SNMP parameters, the NTP server output card provides the same WEB panels than the LEDI Network IN (see below). Please refer to parts 2.2 and 2.3 for more details. The NTP server MIB is detailed in page 40. Status bar The status bar is positioned on bottom of the WEB page. It gives information about the NTP server software. It contains the following information: Current UTC time delivered through NTp MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine phase difference between software clock and time code delivered by hardware Current state of NTp software Synchronization state 79 ENGLISH If your product is provided with a NTP server card, the following panel will be displayed: 4.3.2 NTP setup When you click the NTP button, the configuration of the NTP server software of the output card is displayed as shown below: Description Here is the short description of the different fields: ►► STRATUM level the stratum value to be stored in the NTP messages sends to the NTP clients. ►► Reference ID A 4 letters identifier that gives information about the time reference. This value is put in the appropriate field in the NTP frame ►► Security threshold Give the maximum allowed phase difference (in seconds) before locking the NTP server software. This field is initialized to 65536.0 80 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 4. WEB Interface ►► When not synchronized Define the effect on some NTP fields when the LEDI Network Enhanced is not synchronized9. The possible values LI&STRATUM unchanged, STRATUM=0,LI unchanged, STRATUM unchanged, LI=3(11b), STRATUM=0, LI=3(11b) ►► Lock control This checkbox allows the user to control the lock state of the LEDI Network Enhanced. When checked, the NTP server is locked and doesn’t deliver NTP or output signal. When cleared the NTP server is working. ►► Preference A number that allow you to prioritize your different Gorgy-Timing NTP servers. By this way, the server with the highest preference number is chosen in priority by Gorgy-Timing NTP clients. 9/ Time code is not present (server is autonomous) or the received time-code indicates that external synchronization is lost MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 81 ENGLISH ►► RFC868 compatibility Specify the kind of compatibility with RFC868 : Not compatible, UDP Time server or TCP Time server 5. SNMP INTERFACE 5.1. Presentation The LEDI Network IN provides a SNMP v1 interface for fine monitoring and diagnostic. The SNMP protocol allows the supervision of a device through the network. Two kind of information are available through a SNMP interface: ►► A set of variables that can be read. These variables are stored together in a database (MIB) organized in a hierarchical way. The variables are set by the NTP software to reflect its internal states. ►► Some traps that can be generated by the NTP software to indicate important state modification. There is two important parts in the MIB: ►► A general-purpose branch named System. This branch is MIB II compatible. ►► A private branch that contains information specific to the LEDI Network IN product. Private MIBs are described with .MIB files. Two .MIB files are provided on the CDROM in the directory English\LEDINETWORKIN\MIB: ►► The file GtNtpOutBus.mib contains the description of the information related to the output cards – Localization in the MIB: iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).gorgy(8955).hardware(2).ntpOutBus(1) ►► The file GtNtpClient.mib contains the description of the information related to the NTP client software – Localization in the MIB: iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).gorgy(8955).software(1).ntpClient(4) ►► The file GtNtpServer.mib contains the description of the information related to the NTP server output card software – Localization in the MIB: iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).gorgy(8955).software(1).ntpSrv(3) 82 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 5. SNMP INTERFACE 5.1.1. Structure of the private MIB for LEDI Network IN Software ENGLISH This branch contains all the information related to the client software itself. Here is the structure of this branch: The different fields of this branch are described below: ►► ntpCliHeader A short description of the product. It should be something like GT LEDI Network IN client nnnnnn Vxx.yy (yymmdd) where xx.yy is the current version of the software, yymmdd is the release date of the software (dd/mm/yy) and nnnnnn is the serial number of the product. ►► • ntpCliProduct A description of the product with its options that should be similar to the product code (described in Erreur ! Source du renvoi introuvable.). For example 9257/ AB........D indicates a LEDI Network IN with IRIG-B and ASCII outputs and a display (code D). MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 83 ►► ntpCliVersionNumber Version of this product. It’s something like Vxx.yy (yymmdd) where xx.yy is the current version of the software, yymmdd is the release date of the software (dd/ mm/yy) ►► ntpCliSerialNumber Serial number of this product on 6 digits. ►► ntpCliMAC Hardware address of the Ethernet interface of the LEDI Network IN. This address is on the form aa:bb:cc:dd:ee (6 binary bytes). ►► ntpCliMessageString A text that gives the description of the last generated trap. This text is also attached to the trap. ►► ntpCliResetInfo A text that indicates why the product has restarted (reconfiguration or hard reset). ►► ntpCliSoftwareState This field gives the current state of the NTP client software. It can take one of the following values: ►► Idle: the product has just started. ►► Autodetection: no NTP server has been specified and the product is trying to detect NTP server(s). ►► Autodetectfail: no NTP server found for synchronization – the product will use a server as soon as you connect a server on your network. ►► Learning: the software is currently learning network properties. ►► ntpCliSyncMode The synchronization mode currently used. It can be one of the following values: ►► Autodetect: no NTP server has been specified and the product is trying to detect NTP server(s). ►► Sync1server: works with only one NTP server. ►► Sync2server: works with two NTP servers. When a server fails, it uses the other one. ►► Sync3server: works with 3 NTP servers. When a server fails, it uses one of the other servers. 84 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 ►► ntpCliSyncSrvTable A table that contains all the servers used for synchronization and information. First entry in the table is server being used for synchronization. Second entry is the preferred second server, etc. Each entry has the following format: ►► ntpCliSyncSrvRank: rank of the server. Server of rank 1 is used for synchronization. ►► ntpCliSyncSrvAddress: IP address of the server. ►► ntpCliSyncSrvAccuracy: Accuracy of the server as returned in the NTP frame (something like 2^-x seconds). ►► ntpCliSyncSrvUpAccuracy (Gorgy Timing server only) Accuracy of the server as returned during auto-detection stage. ►► ntpCliSyncSrvUpSrvLoad (Gorgy Timing server only) Load of the server (average number of requests per second) as returned during auto-detection stage. ►► ntpCliSyncSrvPrefered (Gorgy Timing server only) A number that indicates a user-defined rank attached to this server. When auto-detection is activated, the LEDI Network IN takes the server with higher rank. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 85 ENGLISH 5. SNMP INTERFACE Hardware The MIB describes which card is detected and what is the configuration for the cards. All the output cards and the display are connected to a same output bus. The different fields of this branch are described below: ►► ntpOutBusCardNumber Number of cards detected on output bus. ►► ntpOutBusCardTable A table that shows all the cards detected on the output bus. Each card is indexed by its address (1..8 for output cards and 9 for the display). Each entry has the following format: ►► ntpOutBusCardIndex: Index of this entry (i.e card address). This value can have a value from 1 to 8 (for output cards) or 9 (for display); ►► ntpOutBusCardState: The state of the card. It can be detected that indicate that the card works correctly, failure if the card don’t reply or scrambled if the reply from the card is incorrect; ►► ntpOutBusCardType: Type of the card (see Erreur ! Source du renvoi introuvable. for a list of the possible output cards types); ►► ntpOutBusCardDescription: A textual description of the card; 86 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 ►► ntpOutBusCardActivation: Indicate if the output of the card activated or deactivated (this feature can be controlled from the WEB interface). If the card cannot be deactivated, this field has the value notapplicable; ►► ntpOutBusCardTimeZone: Time-zone for this output. This is displayed as an offset from universal time. This setting can be changed from the WEB interface; ►► ntpOutBusCardDayLightSavingPolicy: Indicate which day saving time policy is used. If there is no DST, this field has the value <none>. This setting can be changed from the WEB interface; ►► ntpOutBusCardDayLighSavingCurrent: Indicate if Day Saving Time is in effect (value summertime) or not (value wintertime). If Day Saving Time is not activated, this field has the value notapplicable; ►► ntpOutBusCardTotalOffset: Indicate current total offset from UTC. Here is an example of the description of the output cards displayed in a SNMP browser: 5.1.2. Description of the SNMP traps # Related MIB variable Alarm meaning 1 2 3 ntpCliAutoConfig ntpCliAutoConfigDone ntpCliAutoConfigFail Auto configuration of the NTP client (NTP servers searching) : starting, done or fail 4 ntpCliLearning The NTP client begins is synchronization on the remote server. 6 ntpCliPollFail No or not enough reply from current NTP server, trying another one 7 ntpCliSrvElected A new server is elected for synchronisation 5 ntpCliTracking The NTP client is operating normally MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 87 ENGLISH 5. SNMP INTERFACE 5.2. SNMP interface for NTP server card The NTP server card provides its own a SNMP v1 interface for fine monitoring and diagnostic. Its private MIB is described in the file GtNtpServer.mib provided on the CDROM in the directory English\LEDI Network IN\MIB. Localization in the MIB: iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).gorgy(8955).software(1).ntpSrv(3) 5.2.1. Software information MIB for the NTP server outcard General organization This branch contains all the information related to the server software itself. Here is the structure of this branch: General information Information related to the hardware PPS tracking algorithm Information related to the synchronization network dialog Information related to the external synchronization 88 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 5. SNMP INTERFACE General information ►► ntpSrvHeader Short description of the NTP server output card. ►► ntpVersionNumber Version and release date of the NTP server firmware ENGLISH ►► ntpSrvSerialNumber Serial number of the Ethernet interface (unique for each device) ►► ntpSrvMAC Address of the Ethernet interface (MAC address) ►► ntpSrvMessageString A text bound with each generated trap. It contains the text bound to the last generated trap. ►► ntpSrvResetInfo A text that gives the reason of the last RESET. ►► ntpSrvFailure true(1) if there is no time code and that the NTP output is deactivated false(0) if the time code is present or the NTP server software can guarantee the accuracy; NTP output is activated Tracking module information ►► ntpSrvLockedOnSecurity true(1) if a time difference too important has been detected between the NTP software clock and the time returned by the hardware, for security reasons, the NTP server is currently locked false(0) if no significant time difference has been detected ►► ntpSrvLockedManually true(1) if the software has been locked by a user false(0) if the software is not locked by a user ►► ntpSrvRescaleAmount A text that gives the amount of the difference between NTP software clock and hardware time that leads to a security lock unit: second MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 89 ►► ntpSrvRescaling true(1) if the NTP server software is currently rescaling on the hardware. During rescaling stage, the NTP server don’t reply to clients false(0) if no rescaling in progress ►► ntpSrvRequiredAccuracy A text that gives the required accuracy for this NTP software (related to the time provided by the hardware) unit: seconds NTP server outcard: this accuracy is fixed to 0.24414 ms (4096-1 s) ►► ntpSrvSecurityThreshold A text that gives the maximum accepted difference between software clock and hardware time before locking the server unit: seconds NTP server outcard: this value is initialised to 65535.0 seconds Network dialog information & statistics ►► ntpSrvNbNtpRequests Total number of received NTP requests (in fact all the requests received on port 123). When this counter reaches 32767, it reloops to 0. ►► ntpSrvNbRjectedRequests Number of rejected NTP requests. A request can be rejected if it bad-formed, encryption is invalid or the NTP server is locked. When this counter reaches 32767, it reloops to 0. ►► ntpSrvRequestsRate Shows an approximation of the average number of requests per seconds. ►► ntpSrvNbTcpTimeRequests Total number of received TCP Time requests. When this counter reaches 32767, it reloops to 0. ►► ntpSrvNbUdpTimeRequests Total number of received UDP Time requests. When this counter reaches 32767, it reloops to 0. 90 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 5. SNMP INTERFACE External synchronisation information It gives information on an external time reference used by the hardware (for example an antenna). ►► ntpSrvSyncLostDuration Number of seconds since beginning of synchronisation lose or duration of last synchronisation lose ►► ntpSrvStratumLevel Current stratum level. This is the value returned to the NTP client. This value can change when the synchronisation is lost depending on the policy defined in the setup. Moreover, the default value can be changed through the setup. ►► ntpSrvLIValue Current LI value. This is the value returned to the NTP client. This value can change when the synchronisation is lost depending on the policy defined in the setup. ►► ntpSrvAutonomous true(1) if the NTP software is using its own clock to deliver time through the NTP false(0) if the NTP software is using time code from its synchronisation input ►► ntpSrvAutonomous If ntpSrvAutonomous=false, give number of seconds that the server can works without time code at its input If ntpSrvAutonomous=true, give number of remaining seconds before stopping synchronizing equipment through NTP Other texts are possible (for example when there is no possible autonomy) MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 91 ENGLISH ►► ntpSrvExternallySynchronized notapplicable(2) if there is no information on external time reference true(1) if the hardware is correctly synchronized on its external time reference false(0) if the hardware is not synchronized on its external time reference (out of radio coverture?) 5.2.2. Description of the SNMP traps # Related MIB variable Alarm meaning 8 ntpSrvAutonomy Warning: no time code. The time base has less than 3 minutes of autonomy 7 ntpSrvFailure Failure: no more time code and the time base has no more autonomy 6 5 ntpSrvRescaled ntpSrvRescaling NTP server software is rescaled or is rescaling on its PPS source 4 ntpSrvSecurityLock NTP server locked consequently to an abrupt rescaling 3 ntpSrvUserLock NTP server locked by the user 1 2 ntpSrvSynchronized ntpSrvUnSynchronized The hardware is synchronized or not on its time reference 92 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 APPENDIX A – CONNECTIONS This appendix contains a description of the different connectors of the LEDI Network IN. All the plugs are localized on the backside of the product. 1. Connection for all products The backside of the product has a standard power supply plug, the Ethernet RJ45 plug and a RESET button as shown below: 1.2. 18/72V DC product (type ‘9’) The Ethernet connector and the RESET button are the same. Only the power supply plug is different. +V DC 0V MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 93 ENGLISH 1.1. 230V and 115V AC product (type ‘0’) 2. Dual AFNOR/IRIG-B NFS87500 output (‘B’ type) This card has its output on a single 4 points plug. The AFNOR code is available twice on this output. Here is a schematic overview of the AFNOR/IRIG-B output card: TOP AFNOR/IRIG-B output 1 Amplitude Modulator Time code AFNOR/IRIG-B output 2 The output connector is localized on the back side of the rack and is shown below: Here is the pin-out of the connector (the same signal is generated on outputs ½ and ¾) : Output 1 1 94 Downloaded from www.Manualslib.com manuals search engine 2 Output 2 3 4 MDE-LEDI-NETWORK-IN-4065V1.0 APPENDIX A – CONNECTIONS 3. Dual AFNOR/IRIG-B NFS87500 DCLS RS422 and TTL output (‘T’ type) This card has its outputs on a 4 points plug and a BNC connector. The RS422 AFNOR code is available on the 4 points output : 1 2 Tx/Rx - 3 ENGLISH Tx/Rx + 4 The BNC connector provides TTL signal : Tx GND MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 95 4. RS232 and 485/422 ASCII+TOP (‘A’ and ‘R’ type) The ASCII+TOP card has a 4 points plug and a DB9 connector. The 4 points plug is used to output the TOP through static relays and the DB9 plug is used to output time frame using RS-232 levels. Here is a schematic overview of the ASCII+TOP output: Open collector output TOP Time code VCC Driver Static relay output TXD RS-232 line driver RS-232 output TX+ RS-485 line driver RS-485 output TX- The ASCII DB9 connector is localized on the backside of the rack and is shown below. Connector pin-out for RS232 : GND Connector pin-out for RS485 and RS422 : TXD 5 4 9 GND 3 8 2 7 1 6 The pulse (TOP) output is described below. 96 Downloaded from www.Manualslib.com manuals search engine TX+ 5 4 9 3 8 2 7 1 6 TX- MDE-LEDI-NETWORK-IN-4065V1.0 APPENDIX A – CONNECTIONS 5. TOP / ALARM output (‘A’, ‘R’ type and ‘G’ type) 5.1. Pin-out ENGLISH The 4 points plug on the ASCII and ALARM cards can provide a configurable time TOP or synchro/power alarm TOP. The 4 points plug has the following pin-out: static relay output 1 1 2 open collector output 3 4 ►► Static Relay Outputs 1 and 2 : ►► Pin 1, Pin 2 : without polarity ►► Max. switching voltage : 350 V AC/DC ►► Max. switching current : 130 mA ►► Open Collector output ►► Pin 4 : Gnd Pin 3 : + ►► Max. voltage : 45 V ►► Max. current : 30 mA MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 97 Here are some examples of how to use this output : 5.2. Examples of how to use the open collector output (pins 3-4) General case : loudspeaker 3 R + 4 - External DC WaRNING : VDC max = 45 Volts Power ►► You need to add R if the load (LED, loudspeaker,…) does not accept the VDC voltage. ►► To avoid the transistor destruction, limit the input current to 30 mA (i = Vdc / R < 30mA). TTL input command : VDC If VDC = 5 Volts : 3 R Rmin = 4 TTL input so take 5 = 167Ω 0.03 R ≥ 180Ω WARNING : The open collector output is not compatible with an extern power supply with a + pin connected to earth (telecom 48 Volts).. 98 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 APPENDIX A – CONNECTIONS 5.3. Example of how to use the static relay output (pins 1-2) VCC pulse loudspeaker 1 R + - 2 External DC or AC WaRNING : V max = 60 Volts Power WARNING : You must ensure that MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine i= ENGLISH Supply V < 130mA R 99 APPENDIX B – OUTPUT CODE FORMAT This appendix contains a description of the time code used for the different kind of outputs. 1. ‘A’ and ‘R’ type cards (ASCII+TOP output) The default configuration is shown below: ►► The PPS is generated every 30 seconds and is 1 second long; ►► The ASCII frame is generated at the same time than the PPS. This frame is a 23 characters frame with following format: STX D A Y D D / M M / Y Y H H : M M : S S CR Here is a description of the different fields of this frame: Field Size Value/Meaning STX 1 A single byte which value is 2 – mark the beginning of the frame. DAY 3 The day in the week in a human-readable way (MON for Monday, TUE for Tuesday, WED for Wednesday, THU for Thursday, FRI for Friday, SAT for Saturday, SUN for Sunday) DD 2 Day in the month on two characters ASCII (01-31) MM 2 Month in the year on two characters ASCII (01-12) YY 2 Year on two characters ASCII (00 for 2000 – 99 for 2099) HH 2 Hours on two characters ASCII (00 to 23) MM 2 Minutes on two characters ASCII (00 to 59) SS 2 econds on two characters ASCII (00 to 59) CR 1 A single byte which value is 13decimal – mark the end of the frame 100 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 APPENDIX B – OUTPUT CODE FORMAT 2. ‘B’ and ‘T’ type cards (AFNOR/IRIG-B NFS87500) ENGLISH 2.1. Frame format MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 101 2.2. Bit encoding The signal is modulated only on ‘B’ card. The ‘T’ card output signal has TTL level. 102 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 APPENDIX B – OUTPUT CODE FORMAT 3. DCF and TDF time code description Details of message transmitted over a full minute : "0" synchronization bits 1 month day of week (1= monday ; 7= sunday) 10 8 4 2 1 4 2 1 20 10 8 day of month 2 8 4 10 20 M P3 control bits 0 10 50 J+1 =JF JF ES E/H 20 40 4 2 1 P2 20 30 10 8 4 2 40 20 1 P1 10 8 4 2 1 HE HH "0" "1" minutes hours KEY: J Current day JF State holiday ES Standby transmitter used E/H Indicates a seasonal changeover on the next hour HE Summer time HH Winter time P1, P2, P3 Parity bits MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 103 ENGLISH year 40 80 APPENDIX C – TROUBLESHOOTING This section tries to answer to most frequent question concerning the use of your NTP device. First, ensure that the GTNetManager software and a SUN JAVA Virtual Machine 1.4.2_X are installed on your computer. I made a « Scan now ! » with GTNetManager but I cannot see the device ? ►► 1. Verify the cable connection. If Ethernet LEDs are visible, the upper-left LED should be green. Otherwise, there should be a network connection or power supply failure. ►► 2. If you use several VLAN (Virtual Local Area Network), verify that the device is on the same VLAN than your computer. ►► 3. Connect your computer directly to the device using a straight cable. In DHCP mode, the device take automatically an address in the range 169.254.x.y if it does not find any DHCP server. Change your computer IP address in this range, with a network mask of 255.255.0.0. I cannot open the configuration WEB page ? ►► 1. First, is the device reachable with GTNetManager ? YES Your computer and the device should have the same IP range and the same network mask. NO See previous question. ►► 2. If you use the SUN Java virtual Machine 1.4.2_x, go to: Start Menu ► Settings ► ControlPanel ►Java Plug-in ► Advanced - select JRE 1.4.2_ Start Menu ► Settings ► ControlPanel ► Java Plug-in ► Cache - Uncheck “Enable Caching" ►► 3. Has the page been found by the browser (the loading begins but fails after a while) ? NO, PAGE NOT FOUND If you use “Internet Explorer”, go to : Tools ► Inter ►net Options ► Connexions ► Network Parameters ☛☛The browser should not use proxy, uncheck all checkboxes. 104 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 YES WEB page is reachable, but the browser is unable to load it. Open a TELNET session: Telnet < ip address> 9999 Password : gtmt Proceed to a “Factory Default”, then “Quit and save”. Refresh the WEB page. ►► 1. Press ‘F5’ to refresh the WEB page, and go back to output panel. If the output is still missing, see next point. ►► 2. Open a TELNET session: Telnet < ip address> 9999 Password : gtmt Proceed to a “Factory Default”, then “Quit and save”. Refresh the WEB page. ►► 3. If the output is still missing, open the device. Check the black cables connections and the switchs configurations (see Appendix D – MAINTENANCE / Output card switchs verification). The device stay in “Commuting” mode ? ►► 1. The device stays in this mode when it cannot reach any NTP server. Check that the NTP servers are reachable on the network. ►► 2. Open the NTP panel of the configuration WEB page and verify that the IP addresses of the NTP servers are correct. If in “auto-detect” mode, restart your device : the auto-detection is done at start-up. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 105 ENGLISH An output is not visible in the configuration WEB page ? APPENDIX D – MAINTENANCE 1. Procedure to follow to change the battery ►► Tools : Screw Driver ►► Gorgy Timing reference : BAT1728S ►► Life period : 5 years Battery checking ►► Connect the product to the 230VAC during one hour. ►► Remove the power supply. ►► Open the product with the screw driver, the battery is located between the power supply card and the display card Output 1 … Output 2 Output N Synch. input Power Supply Battery Display ►► Disconnect the old battery with the screw driver. ►► Check the voltage, if the voltage is less than 7V, the battery is on failure. ►► Connect the new battery with the screw driver. 106 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 2. Output card switchs verification If you need to add an output card or if an output seems to be in failure (do not appear in the WEB page), open the device and verify the switch configuration on the output cards: Output 1 (the nearest of the supply card 103064) Output 3 ENGLISH Output 2 Output 4 (the furthest of the supply card 103064) 1 output 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 2 outputs 3 outputs 4 outputs 1 2 3 4 5 6 7 8 The 8th switch of each card allows you to test the card by forcing the signal on output. Don’t forget to put it OFF again after testing! 3. Updating Firmware 3.1. Obtaining Firmware Firmware updates and releases notes for GORGY TIMING NTP devices can be downloaded directly from GORGY TIMING WEB site (www.ntp-secured-solutions.com). This tool only runs on a PC running Windows 98, NT, 2000 or XP. The upgrade is an auto-extractable executable. The name of this tool has the following layout: product_upgrade_prevers_new_vers_.exe The different fields of this name are : ►► product_ : name of the product concerned by the update. ►► prevers_ : version of the product concerned by the update. ►► new_vers_ : new version of the product after applying the update. For example, for an update of the LEDI Network from any version 2 to the version 2.11, the update file shall have the name ledinetwork_upgrade_2xx_211.exe. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 107 3.2. Reloading Firmware Download the update executable and run it from your computer or execute it directly from the WEB site. The following window appears at the screen : short description of the update It uses by default the temporary directory defined on your PC To change the directory used to store temporary file, click on this button ►► Click on the Start button to extract all the files needed for the update. When the extraction is terminated, the tool GTNetMng is automatically started. ☛☛When all the files have been extracted correctly, the tool start automatically. 108 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 APPENDIX D – MAINTENANCE Description of the product concerned by the update ENGLISH More information about the update Click on this button to see a complete description of the update To really start the update, enter the IP address of the product in the field IP address and click on the UPDATE ! button. The update process start immediately. When a problem occurs, an error message is displayed. Check the following points: ►► The product to update must be accessible through your network from the PC used to run GTUpdate ►► check that the IP address is valid, compatible with those of your PC and that it’s really the address of a Gorgy Timing product ►► Check that the product to update is powered. ☛☛ When everything is OK, the following panel is displayed : MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 109 APPENDIX E – DATA 1. Measurements The rack is a standard 19” 1U rack. Here are its dimensions: 424 mm 1U = 44 mm 263 mm 482 mm 2. Specifications Power requirement 230 V AC Maximum: 0,1 A max. Typical : 20 mA plus 2mA per output 115V AC Maximum : 0,2 A max. Typique : 40 mA plus 4mA per output 18-72V DC Maximum : 0,6-0,15 A max. Typical : 250mA plus 25 mA per output (18V) 62mA plus 7 mA per output (72V) Environmental Operating Temperature : 5 to 50°C (41 to 122°F) Storage Temperature : -40 to 70°C (-40 to 151°F) Electrical autonomy 4 hours on internal battery 3. Autres spécifications Protocols supported ARP, UDP, TCP, Telnet, ICMP, SNMP, DHCP, TFTP, HTTP, ENDMI, AutoIP, JAVA, NTP, UDP TIME & TCP TIME Network interface 110Base-T with RJ-45 interface Management SNMP, WEB server, Telnet, ENDMI Upgrade Possible through a TFTP server Memory ROM:512K, RAM:128K, EEPROM:2K 110 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 3. Stamp contents The stamp that identifies the product is localized on the top or on the backside of the product. It contains the following information: GORGY TIMING ENGLISH CODE 9257/Xopt N° SERIE nnnnnn The third line contains the serial number on 6 digits (nnnnnn). The second line contains a description of the product: ITEM CODE 9257 / BASIC MODULE – NTP/SNTP input clock POWER SUPPLY 230VAC/50-60Hz 115VAC/50-60Hz 18-72 VDC 0 1 9 OUTPUT EXTENSION (4 MAXIMUM) Alarm in case of mains cut or absence of synchronisation signal input NTP/SNTP – TCXO oscillator AFNOR NFS 87500/IRIGB Sortie ASCII RS485 + PIP Tropicalization DCLS AFNOR & IRIG B (TTL / RS 422) ELECTRONIC BOARD TROPICALIZED Ó Ó Ó Ó Ó Ó Ó G N A B R T U For example, the 9257/9AB code identify a LEDI Network IN with 18/72V Direct Current power supply and two outputs. The first output uses the ASCII protocol, the second one uses the IRIG-B/AFNOR output. MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 111 APPENDIX F – ADDITIONAL DOCUMENTS This appendix contains some documents that can be useful to manage a set of GT products in your installation. Each document is a table that you can freely copy and distribute: ►► Installation description: you can use this table to make a synthetic view of all your installation. ►► Device configuration: you can use this table to record for each device what is the standard configuration of outputs and display. 112 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0 Summarized installation view Installation description Installation date Device description MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine Serial number ENGLISH Who has done this installation Localization 113 Devices configuration Installation description Installation date Who has done this installation Device 114 Downloaded from www.Manualslib.com manuals search engine Output Time Zone&DST configuration MDE-LEDI-NETWORK-IN-4065V1.0 ENGLISH NOTES MDE-LEDI-NETWORK-IN-4065V1.0 Downloaded from www.Manualslib.com manuals search engine 115 5. stop clock option GORGY TIMING SAS Quartier Beauregard 38350 La Mure d'Isère (Grenoble France) Phone: +33 4 76 30 48 20 Fax: +33 4 76 30 85 33 email: [email protected] - www.gorgy-timing.com TECHNICAL SUPPORT +33 476 30 48 20 [email protected] RADIO TIMING®, LEDI®, LEDICA®, HANDI® are trademarks by GORGY TIMING. Number of statement for training provider activity : 82 38 04877 38 Gorgy Timing RC74B38 - Any technical, aesthetic, color modifications can be made without notice. 116 Downloaded from www.Manualslib.com manuals search engine MDE-LEDI-NETWORK-IN-4065V1.0