Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Amplifier print this page MAR-7SM Frequency GAIN, dB Maximum Power, dBm Dynamic Range VSWR MHz Output Input NF (1 dB (no dB Comp.) damage) Typ. DC-2000 9.00 +5.50 +13.00 5.00 Lw=low range(fL to fU/2) U=upper range(fU/2 to fU) fL - fU Min. Absolute Maximum Rating DC Power Thermal resistance Øjc IP3 CurIn Out I P dBm rent Device Volt(V.) °C/W Typ. Typ. (mA) (mW) Typ. (mA) 19.00 1.70 1.70 60.00 275.00 22.00 4.00 120.00 Pin Connections Port RF in RF Out DC Case GND Not Used cb 1 3 3 2,4 - Notes: gain at highest frequency. Full temperature range, except room • Minimum temperature for Dash-4 models. • Frequency at which output power, NF and IP3 are specified: 1000 MHz. resistance Øjc is from hottest junction in the device to the • Thermal mounting surface of the leads. Case Style - WW107 (inch,mm ) weight: 0.015 grams. A B C D E F G H J .012 .10 .020 .092 .085 .060 .007 .026 .235 0.305 2.540 0.508 2.337 2.159 1.524 0.178 0.660 5.969 K L M N P Q R S T .118 .235 .118 .072 .040 .020 2.997 5.969 2.997 1.829 1.016 0.508 Tolerance: .x ± .1 .xx ± .03 .xxx ± .015 inch. • Model number designated by alphanumeric code marking. damage may occur if any of these limits are exceeded. These • Permanent ratings are not intended for continuous normal operation. Amplifier Selection Guide, please click here. • For For Amplifier Environmental Specifications, please click here. Surface Mount Environmental Specifications, please click here. • For Re-flow soldering information is available in "Surface Mount" article. • Low frequency cutoff determined by external coupling capacitors. • Typical Biasing Configuration ERA/MAR/MAV/RAM/VAM Material and Finish: Case material: plastic. Lead finish: tin-lead plate or tin plate. Marking: RF input lead (1) identified by one or both of the following at factory option: (a) diagonally cut lead, which may be 45°(ref) in either direction; (b) orientation mark on the case. Model dash number identified by color dot or alphanumeric code on case. See specification data sheet. • Prefix letter (optional) designates assembly location. voltage must be connected to pin 3 through a bias resistor in order • Supply to prevent damage. See Biasing MMIC Amplifiers. Reliability predictions are applicable at specified current and normal operating conditions. • Aqueous washable. Quality Control Procedures and Environmental Specifications are • General given in Mini- Circuits Guarantees Quality. Hi-Rel, MIL description are given in Hi-Rel and MIL • Prices and Specifications subjects to change without notice. Packaging: Packaging information: Tape Width(mm): 12 Reel Size(inches): 7 Device Cavity Pitch(mm): 8 Devices Per Reel: 1000 Typical Performance Data S11 (Input Return S 21 (Power S12 (Isolation S22 (Output Loss) Gain) Out-in) Return Loss) dB Mag Ang dB Ang dB Mag Ang dB Mag Ang 100.00 0.05 169.00 13.50 173.00 0.11 1.00 0.14 -7.00 26.02 19.17 17.08 500.00 0.03 133.00 13.10 150.00 0.12 6.00 0.13 -41.00 30.46 18.42 17.72 1000.00 0.01 58.00 12.50 122.00 0.13 10.00 0.11 -94.00 40.00 17.72 19.17 1500.00 0.06 11.80 95.00 0.15 10.00 0.13 24.44 113.00 16.48 17.72 148.00 2000.00 0.15 10.50 70.00 0.17 7.00 0.17 174.00 16.48 144.00 15.39 15.39 2500.00 0.27 9.60 48.00 0.18 1.00 0.19 154.00 11.37 165.00 14.89 14.42 3000.00 -8.64 0.37 169.00 8.10 27.00 0.20 -6.00 0.18 144.00 13.98 14.89 3500.00 -6.94 0.45 150.00 6.50 10.00 0.19 0.17 144.00 14.42 11.00 15.39 4000.00 -5.98 0.51 134.00 5.00 -4.00 0.19 0.17 152.00 14.42 15.00 15.39 FREQ (MHz)