Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Long Range Wireless Door Chime 12 Troubleshooting continued PROBLEM POSSIBLE CAUSE SUGGESTED SOLUTION Your Door Chime has stopped sounding. Your Door Chime Receiver batteries may be flat (3C batteries). Replace the batteries in your Door Chime Receiver (3C batteries). If the red indicator light on the Bell Press Transmitter no longer illuminates when pressed then your transmitter battery is flat. Replace your Bell Press Transmitter battery (3LR50-12V). Battery Operated Cat. D641/BLR, D641/BLRCC Instruction Manual Check the distance between your Door Relocate the Door Chime Receiver If you have checked closer to the Bell Press. your batteries and your Chime and Bell Press, they may be Door Chime is still not located too far away from each other. operating... Your Bell Press may be located too close to a metal structure or too close to the ground. Please read all instructions carefully before installation and use. Relocate your Bell Press away from the metal structure or further away from the ground. Specifications 13 Maintenance The HPM Wireless Door Chime is an example of superior design and craftsmanship. The following suggestions will help you care for the Door Chime so you can enjoy it for years: 1. Keep the Door Chime dry. If the Door Chime gets wet, wipe it dry immediately. Liquids might contain minerals that can corrode the electronic circuits. 2. Use and store the Door Chime only in normal temperature environments. Temperature extremes can shorten the life of electronic devices, damage batteries, and distort or melt plastic parts. 3. Handle the Door Chime gently and carefully. Dropping it can damage the circuit boards and can cause the door chime to work improperly. 4. Keep the Door Chime away from dust and dirt, which can cause premature wear of parts. 5. Wipe the Door Chime with a damp cloth occasionally to keep it looking new. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the chime. 6. Use only fresh batteries of the recommended size and type. Always remove old or weak batteries. They can leak chemicals that can destroy electronic circuits. 7. Modifying or tampering with the Door Chime’s internal components can cause a malfunction and might invalidate its warranty. 8. Care should be taken when replacing Receiver batteries. Open casing carefully so as not to damage the internal wiring. Warranty Customer Service HPM Legrand warrants this product for a period of 3 years from the date of purchase. For all Customer Service and Technical Support please call Monday to Friday during business hours. See the Warranty card enclosed with this product for further details. ABN: 31 000 102 661 Battery requirement: Door chime receiver: Bell press transmitter: 3 x ‘C’ batteries (not supplied) 1 x 12V battery (supplied) Box contents • Bell Press • Door Chime receiver • Mounting screws and wall plugs • Double-sided tape 1 HPM Legrand Australia 1300 369 777 www.hpm.com.au HPM Legrand New Zealand 0800 476 009 www.hpm.co.nz 12V d.c 433.92MHz Up to 70m 4.5V d.c 100dB Note: This series of door chimes is not compatible with units from HPM’s D642 and D641/PI series or with D641/BFL. Features • Operating range up to 70m • 2 melodies for selection • Weather resistant bell press LE07952AAA These goods come with guarantees that cannot be excluded under the Australian and New Zealand Consumer Laws. You are entitled to a replacement or a refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Bell press supply voltage: Transmission freq Range: Receiver battery voltage: Sound level: 2 Typical Applications • Visitor alert • Panic button Range 8 4 Bell Press Transmitter The Bell Press Transmitter has one 12 volt battery (type 3LR50) included which should last about 850 days (in excess of 2 years) under normal operating conditions. 5 Door Chime Receiver The Door Chime Receiver is powered by 3 x ‘C’ size batteries (not included). Alkaline batteries are recommended for longer operating life, up to 180 days. IMPORTANT: Do not use rechargeable batteries, do not mix old and new batteries or different types. 6 Installation Up to 70 metres. NOTE: Range depends on location, temperature and battery condition. Door Chime Receiver Step 1: Depress tab on Door Chime Receiver to remove back cover plate. Step 2: I nsert 3 x ‘C’ size alkaline batteries ensuring that the coil springs contact the negative (-) end of each battery. The Door Chime Receiver is fully portable and free-standing and can be placed anywhere in the house (e.g., table, bookshelf, cupboard, mantelpiece, window sill, etc). It can also be fixed temporarily or permanently to a wall as required. BEFORE PERMANENTLY FIXING BELL PRESS AND DOOR CHIME RECEIVER IN PLACE, TEST LOCATION OF BOTH UNITS TO ENSURE SATISFACTORY OPERATION. The Door Chime Receiver has one slotted hang hole on the back. This hole will enable the Door Chime Receiver to be hooked onto a screw and easily removed or relocated. Bell Press Unit Step 1: R emove front plate cover by lifting bottom edge and sliding out. Step 2: I nsert 12V battery (included in pack) ensuring the positive (+) end of the battery is at the (+) in the battery compartment. (see Fig 1.). Step 3: R eplace front plate cover. Figure 1. 1. T he operation and range of your Long Range Wireless Door Chime depends on location, temperature and battery condition. 2. T ry different locations in your home, ideally 1 metre from floor. Move Door Chime Receiver closer to Bell Press Transmitter to improve operation. 3. D o not expose either unit to rain or immerse in water. 4. Avoid locations where the Bell Press Transmitter is exposed to direct summer sunlight. 5. Do not leave exhausted batteries in Door Chime Receiver or Bell Press Transmitter. 6. C lean only with a damp cloth and mild detergent. Do not use solvents 9 Changing Operating Channels Should your Door Chime Receiver activate intermittently for no reason, it is possible that the uncontrolled activation may be caused by another unit operating nearby on the same frequency coding. The encoded frequency of the transmitter (Bell Press Transmitter) and receiver (Door Chime Receiver) can be changed to avoid this problem. BACK OF DOOR CHIME RECEIVER BACK OF BELL PRESS TRANSMITTER First 6 pins are the radio wave channels. Radio Sound Wave Chime Two last pins are the sound chimes. For example: Jumper on Row #3 in both units to be on the same channel. Figure 2. First, turn the two devices so their backs are facing you. Using long nose pliers, place a jumper (small black device included in pack with the adhesive ‘ foam pads’ or double-sided tape) on the same row of pins on both devices. To change the preset channel place the jumpers on same row #. (See Fig 2.) It is essential that the jumper positions are the same for both units. Test to ensure correct operation. NB: Use of long nose pliers to install jumper may be required. Bell Press Transmitter Step 4: P ress the Push Button to ensure that the red LED indicator lamp lights, indicating that the battery is correctly installed. Step 5: Fix the unit either directly to your front door or a position close by using the self-adhesive foam mounting pads supplied. The chosen mounting position should not be exposed to direct sunlight or rain. The device can also be used as a remote control and doesn’t require any installation. IMPORTANT: Do not mount the Bell Press Transmitter on metal or near a metal door frame, security door, or in close proximity to any metal outdoor furniture as the range of the unit will be substantially reduced. 7 Important Notes OPEN 3 Up to 70 metres. NOTE: Range depends on location, temperature and battery condition. Door Chime Operation Press the button on the Bell Press Transmitter. The Door Chime will sound. Press Chime Button again to repeat chime. 10 Tone Selection The tone selector is located in the Bell Press Transmitter. The two last pins (see Fig 2) are the 2 possible chime tones. To change tone simply remove jumper and fit on the last row of pins. 12 Troubleshooting PROBLEM POSSIBLE CAUSE SUGGESTED SOLUTION The Door Chime is intermittent when it is activated or sounds when not activated. A similar door chime with the same frequency is operated nearby. Change the channel of your Door Chime and Bell Press (refer to Changing Operating Channels).