Download Dual-Color Chip LEDs with Reflector 1210 3.0 2.5 t=1.3mm

Dual-Color Chip LEDs with Reflector
1210 <3.0 2.5 t=1.3mm> Standard Type
SML-020 Series
Emitting Color
Part No.
Material
Green(Yellowish Green)
Red
GaP
GaAIAs on GaAs
Package Size(mm)
SML-020MLT
3025(1210) 3.0×2.5(t=1.3)
Absolute Maximum Ratings (Ta=25∞C)
(mW)
SML-020MLT
:Duty
Green
(Yellowish Green)
Red
60
25
60
30
75
4
-30 to +85
3.0
1.3
2.3
0.5
Red
2.1
Part No.
Peak
Forward
Reverse Operating
Storage
forward
current
voltage temperature temperature
current
IF
VR
Topr
Tstg
IFP
(mA)
(V)
(°C)
(°C)
(mA)
2.5
Power
Emitting dissipation
color
PD
Dimensions (Unit:mm)
Green
-40 to +85
Cathode mark
LED Die
1/5, pulse width 1ms.
Electrical Optical Characteristics (Ta=25∞C)
Part No.
Resin Color
Typ.
(V)
SML-020MLT
IF
(mA)
Max.
(µA)
VR
(V)
20
100
4
Transparent 2.2
Colorless 1.75
Light wavelength
Peak Half-wave
λp
∆λ
Typ.
(nm)
Typ.
(nm)
570
40
660
25
0.8
Reverse
current
IR
Brightness
IV
3
IF
(mA)
20
2
1
4
3
2
1.5
Forward
voltage
VF
Green
1
Min. Typ.
IF
( mcd) (mcd) (mA)
20
20
9.0
16
1.0
Terminal
4
Red
Tolerance:±0.2
Directivity (Typ.)
Angular Displacement (deg)
Green
X
Red
0°
Y
30°
30°
Green
Red
60°
60°
90°
100
50
0
90°
100
50
RELATIVE LUMINOUS INTENSITY (%)
Red
X’
Angular Displacement (deg)
0°
Y’
30°
Green, Red
30°
Green
60°
60°
90°
100
50
0
50
90°
100
RELATIVE LUMINOUS INTENSITY (%)
Recommended Pad Layout
Packaging Specifications (Unit:mm)
Tape Specifications:T86 <2,500pcs/reel>
1.05 0.6 1.05
Reel Specifications
Tolerance:±0.2
φ 180 −30
φ 60 +10
φ 13
1.75±0.1
5.5
3.4
2.9
0 to 0.5
(Unit:mm)
The recommended thickness of the screen mask
for soldering is between 100 and 150µm. The
hole size of the screen mask should be same as
the recommended land pattern or smaller.
8
φ 1.5 +0.1
0
1.7
1.0
2±0.05
3.5±0.05
1.7
Feeding direction
4±0.1
1.6
Label Position
11.4±1
Tolerance:±0.2
Rev.C
Electrical Characteristic Curves
Forward Current - Forward Voltage
Ta=25°C
-------
1.6
SML-020MLT <Green>
IF=20mA
RELATIVE LUMINOUS INTENSITY
FORWARD CURRENT : IF (mA)
50
Relative Luminous Intensity - Case Temperature
SML-020ML <Red>
10
1.0
1.4
-------
SML-020MLT <Green>
SML-020MLT <Red>
1.2
1.0
0.8
0.6
0.1
0.4
1.5
2.0
2.5
3.0
-20-10 0 10 20 30 40 50 60 70 80
FORWARD VOLTAGE : VF (V)
CASE TEMPERATURE : Tc (°C)
Relative Luminous Intensity - Forward Current
3.0
Ta=25°C
2.5
2.0
1.5
1.0
0.5
0
0
10
20
30
40
50
Ta=25°C
RELATIVE LUMINOUS INTENSITY
RELATIVE LUMINOUS INTENSITY
3.0
----
SML-020MLT <Green>
----
SML-020MLT <Red>
----
SML-020MLT <Green>
----
SML-020MLT <Red>
2.5
2.0
1.5
1.0
0.5
0
0
60
PEAK FORWARD CURRENT : IF peak (mA)
10
20
30
40
50
60
PEAK FORWARD CURRENT : IF peak (mA)
2.4
1
5 10 20
50 102
103
104
PULSE DURATION : Tw (µs)
100Hz
200Hz
500Hz
1kHz
2kHz
5kHz
10kHz
20kHz
5
50kHz
RATIO of MAXIMUM TOLERABLE PEAK CURRENT IF peak Max.
IF Max.
to MAXIMUM TOLERABLE DC CURRENT
100Hz
200Hz
500Hz
1kHz
2kHz
5kHz
10kHz
20kHz
5
50kHz
RATIO of MAXIMUM TOLERABLE PEAK CURRENT IF peak Max.
IF Max.
to MAXIMUM TOLERABLE DC CURRENT
Ratio of Maximum Tolerable Peak Current - Pulse Duration
2.5
1
5 10 20
50 102
103
104
PULSE DURATION : Tw (µs)
MAXIMUM FORWARD CURRENT : IF Max. (mA)
Derating
-------
30
SML-020MLT <Green>
SML-020MLT <Red>
20
10
0
0
10
20
30
40
50
60
70
80
90
AMBIENT TEMPERATURE : Ta (°C)
Rev.C
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1