Download virtual simulation for radiatiotherapy treatment using ct medical data

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Positron emission tomography wikipedia , lookup

Proton therapy wikipedia , lookup

Backscatter X-ray wikipedia , lookup

Nuclear medicine wikipedia , lookup

Medical imaging wikipedia , lookup

Neutron capture therapy of cancer wikipedia , lookup

Radiosurgery wikipedia , lookup

Fluoroscopy wikipedia , lookup

Image-guided radiation therapy wikipedia , lookup

Transcript
VIRTUAL SIMULATION FOR RADIATIOTHERAPY
TREATMENT USING CT MEDICAL DATA
Dr. Stelios Zimeras ([email protected])
University of the Aegean,
Department of Statistics and Assurance Sciences,
83200 Karlovasi – Samos,
Greece.
Abstract
Simulators are medical devices used in the oncology
clinics to perform the simulation for the external beam
radiotherapy treatment. Unlikely for a clinic to obtain a
real Simulator is a high investment in terms of money,
space and personnel. The alternative here can be a Virtual
Simulator (VS). The CT simulators are system-software
that can perform the simulation process using the
Computed Tomography (CT) data set of the patient,
including the external patient’s skin landmarks, instead of
the physical patient. In this paper, a new high
performance CT based virtual simulation system running
on a low cost widely available PC hardware – EXOMIO
would be presented. The implemented high-end
visualization techniques allow the users to simulate every
function of the real simulator including the mechanical
component movements, radiation beam projection and
fluoroscopy.
1 INTRODUCTION
Radiation therapy (RT) uses high-energy photon rays in
order to deliver a very accurate dose of radiation to a
well-defined target volume with minimal damage to
surrounding healthy tissues. The desired result is the
eradication of the disease and the improvement or
prolonging of patient’s life. RT is a very demanding
process that requires accuracy and effectivity. The RT
process is composed of several steps. One important step
in this process is simulation. Simulation provides
localization of the target volume, the area that will receive
the maximum amount of dose, and delineation organ at
risk, the volumes and organs that must receive the
minimum dose. Once these structures have been well
defined, the next step is the definition of the irradiation
fields in relation with the target volume and the organs at
risk. During treatment, the patients receive their therapy
via a number of fractions. Therefore, there must be a
confirmation that the irradiation orientation and the
structure localization remain unchanged. One of the
significant technological advances in radiation oncology
in the past 20 years is the implementation of CT-based
virtual simulation in the clinical routine. The concept,
often termed CT-Sim virtualises the simulation process
that is performed on a
conventional simulator. The
patient is scanned on the CT device together with
localization-reference markers made from radio-opaque
material (e.g. aluminium), which are attached on the
patient’s skin. The volumetric CT data are directly
transferred to the CT-Sim via the local network of the
clinic. This work describes a new CT based virtual
simulator system, EXOMIO1, that has been developed at
Fraunhofer IGD in collaboration with Städtisches
Klinikum Offenbach, department for radiation therapy,
and is now used in clinical practice already at several
institutes worldwide. Its main advantages are: (a) it is
based on low cost and widely available hardware (PC),
unlike the other commercially available systems that
depend on expensive workstations, (b) it provides high
quality and high performance visualization tools and (c) it
can be connected via network to any DICOM supporting
CT or MR scanner and via DICOM-RT supplements it
enables support for treatment planning system and
verification system at linear accelerators.
2 METHODS AND MATERIALS
2.1 Principle of Computer Tomography (CT)
Computer Tomography is a technology that allows the
non- destructive evaluation of the internal structure of the
objects. Since a lot of year this technique haw been used
successfully in medicine and material testing to examine
local differences in density by generating images of
different cutting planes of the object concerned. The
basics of CT imaging are that of x-ray principles.
When x-rays pass through a patient’s body and are
absorbed, they in turn create a profile of x-rays beams.
The profiles are stored on files which to state basically
creates an image. For CT imaging the film is substituted
by a detector, which measures the x-ray profile. The CT
scanner consists of a gantry, which includes the x-ray
source, x-ray detectors, and data acquisition system, a
patient table, a control console and a computer.
The CT is linked to the computer. The scanner rotates
about the patient, this proceeds as it takes pictures or
slices of tissue. The images in general are then processed
by the computer and either depicted on a cathode-ray tube
and screen or are saved a permanent location on film. The
resulted image is displayed or saved and referred to as CT
slices. More specifically, as the image is being acquired,
1
MedInTec GmbH, Bochum, Germany
the detector is making a 360-degree rotation. During the
rotation the detector takes numerous snapshots (profiles)
of the attenuated x-ray beam. The CT images are
reconstructed from a large number of measurements of xray transmission through the patient. This projection data
are used to reconstruct the CT image (Figure 1). Figure 2
shows an slice from an x-ray CT in the heart lung area.
Figure 3. Current clinical routine for external beam
treatment delivery.
Figure 1. Principle of the X-ray CT scanner
One of the significant technological advances in
radiotherapy in the past 20 years is the implementation of
CT or Virtual Simulators (VS), in the clinical routine.
Sherouse in 1987 [1] first proposed the concept, often
termed CT-Sim to distinguish it from Sim-CT where a
simulator is modiefied for CT use and by the late 1990s
several designs and clinical assessments of CT virtual
simulators have been reported [1-8]. Using VS, the clincal
routine is modefied accordingly (Figure 4) [9,10]:
1.
2.
Figure 2. X-Ray CT slice showing heart and lungs
3.
2.2 Workflow Concept
The affect of the radiotherapy treatment is based on the
precise delivery of high irradiation dose on the tumor site
without damaging the surrounding healthy tissues.
Therefore patient positioning, target volume definition
and irradiation field placement are vary critical steps
while planning the irradiation process. Briefly in the
current clinical routine using, the patient goes through the
following steps (Figure 3):
1.
2.
3.
4.
5.
Localize area to be irradiated on the Simulator
Collect patient’s CT data including attached
aluminium markers.
Transfer CT data to treatment planning system (TPS),
where physicians perform the tumour volume
definition. In this step the physicist will define the
organs at risk, will place the necessary fields to
perform the specific treatment technique and she/he
will calculate the dose distribution around the tumour
area and the organs at risk.
The treatment plan parameters will by verified on the
real Simulator.
Verify patient position on (Linear Accelerator)
LINAC before irradiation.
4.
5.
Collect patient’s CT data including attached
aluminium markers.
Transfer CT data to VS. The physician defines the
tumour volume and the organs at risk and she/he will
place the necessary fields relative to the tumour
volume.
The simulation plan and the CT data are transferred
via DICOM (Digital image and Communication in
Medicine) server to the TPS for dose calculation and
final treatment plan optimization.
Verify patient position on LINAC before irradiation.
Perform treatment on the treatment machine (Linear
Accelerator or LINAC).
Figure 4. Current clinical routine for external beam
treatment delivery.
Considering the above steps, one can evaluate the
importance of the communication requirements of a CT-
Sim. In EXOMIO the philosophy of the stand-alone CTSim system is adapted. In practice, the system is capable
to interface any CT scanner device and any treatment
planning system through DICOM communication
protocol. The DICOM protocol is used for
communicating digital images from the medical imaging
modalities, and the DICOM-RT supplements to
communicate structures and beam data to/from the
treatment planning systems and verification systems. All
datasets can be stored in the EXOMIO server and one can
access them from any client installed on the local network
of the institution.
movements of the mechanical component and description
of the component’s dimensions (e.g., multileaf collimator,
or MLC) (Figure 5).
2.3 Main System Features
The main system features can be separated into several
categories including visualization features, volume
definition tools, treatment field design, patient set-up and
simulation plan documentation. In this paper only a small
part of the visualization capabilities will be presented.
EXOMIO has the ability to generate 2D and 3D images
using only the original CT data of the patient. The 2D
images displayed are the original axial CT, MR or PET.
Multi planar reconstructions (MPR) can be generated in
real time in the orthogonal, coronal and sagittal directions,
and any oblique direction. The 3D reconstructed images
are a must in CT-Sim systems in order to simulate the
patient anatomy and the images generated from the real
simulator or the treatment machine. The first layout
contains four windows and the displayed images are the
Beam’s Eye View (BEV), the Observer’s Eye View
(OEV) and the Room View (RM), together with the axial
slices. The second layout is composed again of four
windows, containing the three orthogonal slice directions
and the OEV. This layout is ideal for navigation through
the CT volume, for volume delineation and to observe
complex radiation field arrangements. The last layout
contains every image described above. This layout has six
windows emphasizing the size of the BEV image, since
the physicians feel comfortable working with this image.
In both rendering views, OEV and BEV, the volume
orientation is controlled using a mouse track-ball. The
user simply clicks-and-rotates the patient’s volume to any
viewing angle. The same principle is used with the BEV
image but in this case only the rotations of gantry and
table are possible.
EXOMIO can use large amounts of data, from 40 up to
300 slices, in order to produce high quality anatomical
images. This system enables reading of CT data, acquired
not only with a single slice CT scanner (such as a
Siemens SOMATOM Plus 4), but also multi-slice data
ranges, acquired in this study with four slices
(SOMATOM Volume Zoom). EXOMIO can be
connected via network directly to any CT scanner that
support DICOM protocol. The system allows the
adaptation to any LINAC configuration through a
machine configuration module that is designed according
to the international standard for radiotherapy equipment
(IEC 1217). This configuration involves limitation on
Figure 5. The six-window layout of EXOMIO. On the left
side the slices windows, the middle lower window is the
OEV, the lower right the Room View and the upper right
hosts the BEV.
2.4 Volume Visualisation
3D image reconstruction using volume rendering is the
most essential component, the “heart” actually, of a CTSim system. The 3D reconstruction of complete patient
anatomy for different anatomical sites is of great benefit
for the clinicians. Only a small part of the patient’s
anatomy can be visualized on the conventional simulator
during fluoroscopy mode, a drawback that comes due to
the limited size of the detection surface of the image
intensifier.
The rendering pipeline used in EXOMIO is based on the
work of G.Sakas [13]. In BEV we use perspective
projection and in the OEV parallel projection but both
views support the same illumination models: transparent
mode using maximum intensity projection (MIP) [14], Xray [11], and surface reconstruction mode using iso-value,
gradient [12] and semi-transparent. In both illumination
models, surface and transparent, one can visualize
selected tissue ranges using linear or triangle look-up
table. The volume-rendering pipeline is based on the
widespread ray-casting algorithm. In other words the
rendering process can be spread when more than one
processor are available on the hardware. Additional
important factors for the reconstruction speed of the final
image are the data set size and the size of the final 3D
image, which influence the number of rays used during
volume reconstruction. Nevertheless, in practice the 3D
images in EXOMIO can be calculated almost in real time.
The most common image presented in the CT-Sim
systems is the virtual X-ray image generated from digital
CT or MR volumes. These images are often called the
digitally reconstructed radiographs (DRRs). The term
DRR is used when we refer to those X-Ray images that
are generated with an unrealistic way using direct volume
rendering techniques or to those images that are generated
from volume data using a better approximation of the
physical model. In both cases we try to simulate the
attenuation of the X-ray through the digital patient’s
body. The manipulation of tissue properties like the mass
attenuation coefficient, assist the generation of unique
images simulating physical principles of radiographic
imaging. The most common example is the generation of
mega-voltage DRR images for direct comparison with the
portal images. In addition DRR images provide unique
anatomical information to the clinicians that no
conventional X-ray device can produce. An example of
different X-ray reconstruction modes is illustrated in
Figure 6.
Figure 6. Volume rendering modes supported from
EXOMIO. On the top row from left to right: isovalue
mode, semitransparent mode and maximum intensity
projection. On the lower row X-ray images reconstructed
using different tissue ranges. From left to right: full tissue
range, muscle tissues and lung tissues.
Another type of 3D image with high importance in CT
simulation is the external body surface anatomy. Highresolution volumetric CT data in combination with
volume rendering techniques can produce a very accurate
representation of 3D patient anatomy. This concept is
extremely suitable for assessing the configuration of the
radiation beam in three dimensions. EXOMIO supports
the visualization of the irradiation beam and block
arrangement as 3D semitransparent objects. In addition
the light field projection of the radiation field, delineated
or not, can be simulated and manipulated in real time
during field rearrangement or shielding block-contour
design (Figure 7).
Figure 7. The light field projection on patient’s skin (left).
3D beam object reconstructed with patient’s CT data
(middle). Virtual light field projection on patient’s
surface.
2.5 Volume Definition Tools
Target volume and critical structure definition is a
complex and time-consuming process in radiotherapy.
The complexity varies for different anatomic sites. In CTsimulation and plan evaluation, both the physicists and
radiation oncologists interact closely to subjectively
identify the plan most appropriate for the individual
patient. In order to reduce the investment of time and
effort by the radiation oncology staff, several image
analysis tools are integrated. The system allows the user
to draw contours around the tumour, target, and normal
tissues on a slice-by-slice basis and provides, at the same
time, a cross-reference to planar images.
A function that significantly accelerates the contouring
process is the linear interpolation between the original
key-contours. The same principle can be applied for
defining structures in both planar planes, sagittal and
coronal. The contour edit functions allow the user to
move, scale and rotate an entered contour in addition to
providing tools for rapid contour corrections and copying
to inferior and posterior slice. Organs with large
differences in their intensities can be segmented semiautomatically. In terms of user effort the only action
required from the user is the selection of an initiation
point for the algorithm on the original axial slices. The
complete 3D geometry of the organ will be traced
automatically. Some of the common organs with high
sensitivity factor and vital importance are the lungs, the
spinal cord and the trachea [15-19]. In addition to those
organs, the external body contour can be extracted in a
similar manner. The contours that are generated semiautomatic can be manipulated and modified at the same
manner as those defined manually. The user has the
possibility to reconstruct the segmented organs as
volumetric structures on the BEV and OEV images.
Figure 8 illustrates different 3D reconstruction examples
of segmented structures.
In figure 10 an oblique cut in the OEV window is shown
and is used for the validation of the field configuration
through the 3D patient volume. Figure 8 demonstrates the
overall 3D nature of the EXOMIO simulator. This
includes the addition of a fifth field, which is noncoplanar to the four fields in the box-technique.
Figure 8: 3D segmentation images for different organs :
Skin, Lungs and Spinal canal, Bronchus, Spinal canal
with left lung and tumour, Spinal canal and Lungs
(different view).
3
RESULTS
One example of the use of EXOMIO in clinical practice
would be presented. The patient is a 75 years old patient
with stage T3N0M0 cancer of the prostate. The radiation
fields cover the entire prostate glands, which includes
safety margins. For this case, CT slices of 3mm thickness
and 3mm slice distance have been reconstructed using
spiral CT acquisition from a 512x512 pixel matrix.
Figure 9 shows the clinical target volume (CTV)
delineation procedure. EXOMIO offers the possibility to
contour the CTV in at least three planes (one sagittal, one
coronal and at least one axial CT plane) and it
automatically extracts the 3D CTV. The physician can
then do fine contour corrections if necessary. After the
CTV is validated the physicians decide the appropriate
clinical margins. In this prostate case anisotropic margin
of 10 mm in the lateral, 10 mm in the cranio-caudal and 0
mm in the ventro-dorsal axes have been used.
Figure 10: Planning of an additional fifth beam noncoplanar to the four fields of the box-technique. (Top left)
Coronal plane. (Centre left) Sagittal plane. (Bottom left)
CT slice with the fifth field. (Top right) DRR for the new
field with the automatically on PTV adapted block:
irregular field. (Bottom centre) OEV showing the patient,
the beam cone and the light field projection on the skin
for the fifth field and the 3D PTV. (Bottom right) 3D
room view of the virtual simulator and patient.
4
Figure 9: Automatic extraction of PTV from delineated
CTV in EXOMIO by applying user defined clinical
margins. The extracted PTV and CTV are shown in
different colours in the three major planes and in the OEV
(3D).
DISCUSSION
The advantages of CT-based virtual simulation are well
known and include the fact that target volumes, critical
organs and structures can be effectively defined and
displayed in multiple image planes (axial, coronal, sagittal
or oblique). Improved manual and automated contouring
tools greatly simplify normal critical structure, tumour,
and target volume delineation. A direct interface to the
treatment planning system permits efficient virtual
verification. In CT-Sim it is possible to display more
information on the same screen such as: (a) the beam’s
eye-view, where the Digital Reconstructed Radiograph is
displayed, (b) the room view including a 3D model of the
simulator or the treatment machine and (c) the observer’s
eye-view, where the 3D surface reconstruction of the
patient is shown. These images offer the user an overview
of the simulation and treatment planning process.
Furthermore, in virtual simulation one can observe larger
parts of the patient’s volume than on the conventional
simulator where fluoroscopy is limited by the dimensions
of the image intensifier (detector). According to our
clinical experience the CT-Sim system could simulate all
of the treatment cases, replacing completely the real
simulator. The CT-Sim system has been easily integrated
into our clinical radiotherapy routine. The modification
required in the CT room was the installation of the laser
marking system for the registration of the treatment
reference point, similar to the installation in the LINAC
room. In addition, the flat CT table-top had to replace the
original curved table-top.
Visualization of multileaf collimator (MLC) field is only
possible with CT-Sim and this is most important because
of widespread use of MLCs. CT-Sim also makes it
possible, without the patient needing to be recalled, for
verification to be repeated after changes to the treatment
plan. Indeed, CT-Sim may eliminate the requirement for a
conventional simulator for several treatment sites. All the
main features of a classical simulator are available,
software based, in EXOMIO. The validation of beam
geometries in a classical simulator is only based on X-ray
contrast between tissues of different densities such as
bone, lung or a contrast filled organ such as the bladder.
In particular CT based simulation enables accurate
delineation of multi-field geometries, all necessary field
matching and multi-planar field adaptation as shown in
our results. These functions are not possible with classical
simulation. In addition the CT based virtual simulation
brings benefit for patient scheduling because it avoids the
often experienced bottlenecks in patient workload flow
within a department of radiation oncology. Finally 3D
visual representation of the particular organ, in addition
with the clinical examinations, could be a powerful tool to
the doctors for diagnosis, medical treatment or surgery.
5
ACKNOWLEDGEMENT
The author would like to thank Prof George Sakas and
Grigoris Karangelis for the useful scientific help and
comments about the progress of this work. Also many
thanks to MedCom Company and Städtisches Klinikum
Offenbach whom gave him equipments and medical data
sets for the implementation of the above work. Finally the
author would like to thank the EC and the Marie Curie
Fellowship Association for this great opportunity to work
with different people. This work was supported by a
Marie Curie Industry Host Fellowship Grant no: HPMICT-1999-00005 and the author is a MCFA member.
6
REFERENCES
1 Sherouse, G.; Mosher, C.; Novins, K.; Rosemann, J.;
Chaney, E.L. “Virtual simulation: concept and
implementation”. In: Proceedings of 9th International
Conference of the Use of Computers in Radiation
Therapy (ICCR). Scheveningen, The Netherlands:
North Holland Publishing Co.; 1987:433-436.
2 Nagata, Y.; Nishidai, T.; Abe, M.; Takahashi, M.;
Okajima, K.; Yamaoka, N.; Ishihara, H.; Kubo, Y.;
Ohta, H.; Kazusa, C. “CT Simulator: A new 3-D
3
4
5
6
7
8
9
10
11
12
13
14
15
16
planning and simulating system for radiotherapy: Part
2. Clinical application.” Int J Rad Oncol Biol Phys
1990;18:505-513.
Nishidai, T.; Nagata, Y.; Takahashi, M.; Abe, M.;
Yamaoka, N.; Ishihara, H.; Kubo, Y.; Ohta, H.;
Kazusa, C. “CT Simulator: A new 3-D planning and
simulating system for radiotherapy: Part 1. Description
of system.” Int J Rad Oncol Biol Phys 1990;18:499504.
Rosenman, J.; Sailer, S.; Sherouse, G.; Chaney, EL.;
Tepper, JE. “Virtual simulation: Initial clinical
results.” Int J Rad Oncol Biol Phys 1991;20:843-851.
Sherouse, G.; Chaney, EL. “The portable virtual
simulator.” Int J Rad Oncol Biol Phys 1991;21:475482.
Perez, C.; Purdy, J.A.; Harms, W.; Gerber, R.;
Matthews, J.; Grigsby P.W.; Graham, M.L.; Emami,
B.; Lee, HK.; Michalski, JF.; Baker, S. “Design of a
fully
integrated
three-dimensional
computed
tomography simulator and preliminary clinical
evaluation.” Int J Rad Oncol Biol Phys 1994;30:887897.
Butker, E.K.; Helton, D.J.; Keller, J.W.; Hughes, L.L.;
Crenshaw, T.; Davis, L.W. “A totally integrated
simulation technique for three field breast treatment
using a CT simulator.” Med Phys 1996;23:1809-1814.
Chen, G.T.Y.; Pelizzari, C.A.; Vijayakumar, S.
“Imaging: The Basis for Effective Therapy.” Front
Radiat Ther Oncol 1996;29:31-42.
Michalski, J.M.; Purdy, J.A.; Harms, W.; Matthews,
J.W. “The CT-Simulation 3D Treatment Planning
Process.” Front Radiat Ther Oncol 1996;29:43-56.
Karangelis G, Zamboglou N: “EXOMIO: A 3D
Simulator for External Beam Radiotherapy.” , Volume
Graphics 2001- Proceedings of the Joint IEEE TCVG
and Eurographics Workshop in Stony Brook, New
York, USA, Springer-Verlag Wien New York, 2001
351-362.
Cai, W. “Transfer functions in DRR volume
rendering.” CARS'99, Paris, France, June 1999, 23-26.
Levoy, M. “Display of surface from volume data.”
IEEE CG&A, 1988:8(5).
Sakas, G. “Interactive volume rendering of large
fields”. The Visual Computer, 1993, 9(8):425-438.
Sakas, G., Grimm, M. and Savopoulos, A. “Optimised
maximum intensity projection (MIP)”, Rendering
Techniques'95, Springer Verlag 1995:51-63.
G. Karangelis, S. Zimeras, E. Firle, Min Wang, G.
Sakas: “Volume definition tools for medical image
applications”, 4th MICCAI International Conference,
Utrecht, Neitherlands, M.-A. Viergever , T. Dohi, M.
Vannier (eds.), Springer-Verlag, Lecture Notes in
Computer Sciences 2208, pages 1295-1297.
S. Zimeras, G. Karangelis: “Semi-automatic
Segmentation Techniques for CT Medical Data”, 3rd
caesarium Computer Aided Medicine November 1213, Bonn, Germany, 2001.
17 G. Karangelis, S. Zimeras: “An Accurate 3D
Segmentation Method of the Spinal Canal Applied on
CT Images”, BVM 2002, Confedrence Proceedings
Meiler M, Saupe D, Kruggel F, Handels H, Lehmann
TM, (Hrsg) Bildverarbeitung für die Medizin 2002,
Springer-Verlag, Berlin, 2002, 366-369, Germany.
18 S. Zimeras, G. Karangelis, E. Firle: “Object
segmentation and shape reconstruction using
computer-assisted segmentation tools”, Medical
Imaging 2002, San-Diego, USA.
19 G. Karangelis and S. Zimeras: “3D segmentation
method of the spinal cord applied on CT data”,
Computer Graphics Topics, 1/2002, Vol 14, 28-29.