Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
This Datasheet is for the IC693MDL751 12/24 Volt DC Positive Logic Output, 32 Point http://www.cimtecautomation.com/parts/p-14673-ic693mdl751.aspx Provides the wiring diagrams and installation guidelines for this GE Series 90-30 module. For further information, please contact Qualitrol Technical Support at 1-800-784-9385 [email protected] 7 Discrete Output Modules 12/24 Volt DC Positive Logic Output, 32 Point IC693MDL751 The 12/24 volt DC Positive Logic Output module for the Series 90-30 Programmable Logic Controller provides 32 outputs in four groups of eight with two common pins for each group. The Output module is designed to have positive logic characteristics in that it sources current to the loads from the user common or positive power bus. The output device is connected between the negative power bus and the module output. The output characteristics are compatible with a wide range of user-supplied load devices, such as motor starters, solenoids, and indicators. Power to operate the field devices must be supplied by the user. Connections from the output circuits are made to the user’s output devices through a 50-pin connector mounted on the front of the module. This module does not have LED indicators to indicate circuit status. This output module can be installed in any I/O slot of a 5 or 10-slot baseplate in a Series 90-30 PLC system. Table 7-22. Specifications for IC693MDL751 Rated Voltage Output Voltage Range 12/24 volts DC 12 to 24 volts DC (+20%, –15%) Outputs per Module Isolation 32 (four groups of eight outputs each) 1500 volts between field side and logic side Output Current 0.3 amps maximum per point 2 amps maximum (each common) Output Characteristics Output Voltage Drop Off-state Leakage On Response Time Off Response Time 0.24 volts maximum 0.1 mA maximum 2 ms maximum 2 ms maximum Internal Power Consumption 21 mA (all outputs on) from 5 volt bus on backplane Refer to Appendix B for product standards and general specifications. Wiring to Field Devices Direct Method – This method uses cables that have a mating female connector on the module end and stripped and tinned wires on the other end. You can purchase a pre-wired cable, either catalog number IC693CBL308 (3 feet/1 meter) or catalog number IC693CBL309 (6 feet/2 meters) or, if required for your application, build your own cables. Refer to the IC693CBL308/309 data sheet in Appendix C of this manual for cable information. GFK-0898F Using a Weidmuller Terminal Block – You may purchase a Weidmuller #912263 terminal block from your electronics dealer to use with a GE Fanuc prewired cable. GE Fanuc Cables IC693CBL306 (3 feet/1meter) or IC693CBL307 (6 feet/2 meters) have connectors on each end. These connect from the module connector to a connector on the DIN–rail mounted Weidmuller terminal block. Appendix C has a data sheet for these cables, which includes a figure showing how they connect between the module and the Weidmuller terminal block. Chapter 7 – Discrete Output Modules 7-41 7 IC693MDL751 Output Module Field Wiring Information The following figure provides wiring information for connecting user supplied load devices and power source to the 12/24 volt DC positive logic output module. a44847 TYPICAL CIRCUIT COM INTERNAL CIRCUIT 0V MODULE CONNECTOR FIELD CIRCUITRY TERMINALS WIRING MODULE CONNECTOR FIELD CIRCUITRY TERMINALS WIRING 50 49 45 COM (A) 29 O 16 A1 O 12 B1 O 32 A2 O 28 B2 O 48 A3 O 44 B3 O 15 A4 O 11 B4 O 31 A5 O 27 B5 O 47 A6 O 43 B6 O 30 A7 O 10 B7 O 46 A8 0V (A) O 42 B8 0V (B) 18 OUTPUT CIRCUIT O + 14 USER LOAD XX O MODULE CONNECTOR FIELD CIRCUITRY TERMINALS WIRING OUTPUT CIRCUIT XX + USER LOAD MODULE CONNECTOR FIELD CIRCUITRY TERMINALS WIRING 41 36 COM (C) 40 21 COM (D) O 7 C1 O 3 D1 O 24 C2 O 20 D2 O 39 C3 O 35 D3 O 6 C4 O 2 D4 O 23 C5 O 19 D5 O 38 O 34 D6 O 22 C7 O 1 D7 O 37 C8 0V (C) O 33 D8 0V (D) 9 O COM (B) OUTPUT CIRCUIT + C6 XX 5 USER LOAD O OUTPUT CIRCUIT XX + USER LOAD Figure 7-38. Field Wiring - IC693MDL751 32 Point Output Module 7-42 Series 90-30 PLC I/O Module Specifications – July 2000 GFK-0898F