Download LS-7585 Orthodontic Adhesive Removal Set

LS-7585 Orthodontic Adhesive Removal Set
Procedure by Dr. S. Jay Bowman
The Orthodontic Adhesive Removal Set by Dr. S. Jay Bowman is designed to efficiently
remove residual adhesive after orthodontic appliance removal and provides a smooth
final enamel finish after bonded, banded or Invisalign® treatments.
ISO NO.
Ø 1/10 mm
LG mm
Desc.
MFG. NO.
H375R
016
8.0
H246L
012UF
5.4
P0153
031
16 flutes
H375R-016
30 flutes
H246L-012UF
FG Polisher
P0153-031
Suggested Techniques
Removing Residual Adhesive
After orthodontic appliances have been removed, the NTI® Carbide
(Red) H375R-016* at 35-40,000 rpm is used. This round-end taper
is ideal for removing both orthodontic bonding adhesives and cements
that remain on the teeth after de-bracket and/or de-banding. The
tapered design is easy to manipulate around on the peripheral
enamel surfaces and the round-end reduces potential gingival tissue
impingement. Enamoplasty of mammelons or uneven incisal edges
can be accomplished in this same step and this bur can also be utilized
for removing Invisalign® composite attachments. Ideally, the constant
torque and low vibration of an electric hand-piece is perfectly suited
for use with this bur in this application.
Enamel Surface Finishing
After large, residual composite or cement “tags” are removed from
the enamel surfaces, the resin/enamel interface must be polished.
The NTI® Finishing Carbide (White) H246L-012UF is a long, flameshaped 30-blade bur is perfect for removing the remnants of
adhesives and cements while also finishing the enamel to a smooth
surface with reduced vibration. The versatile, pointed shape can be
positioned just under the marginal gingival while polishing away any
adhesive primers, sealants, or varnishes (often used to help prevent
enamel demineralization) that may yet remain on the enamel. If
used without water-spray, the residual resin is often visible as the air
exhaust from the high-speed contra-angle desiccates the surface of
the tooth, making the polishing process easier.
The intent of this process is to remove any residual adhesives and
cements but not to unintentionally disturb enamel anatomy or overDHESIVE REMOVAL AND POLISHING KIT
polish the surface. Alternatively, specific sitesORTHODONTIC
of uneven Apitted
or S. Jay Bowman, DMD, MSD
ORTHODONTIC ADHESIVE REMOVAL AND POLISHING
KIT
blemished enamel can be refined at this stage.
S. Jay Bowman, DMD, MSD
ORTHODONTIC ADHESIVE REMOVAL AND POLISHING KIT
S. Jay Bowman, DMD, MSD
The appliances are removed.
Enamel Polishing
An NTI® Polisher, green friction-grip FG silicone polisher P0153-031
is used to refine the final enamel surface. This flame or conical
shaped polisher can also be used in the same low or high-speed dental
handpiece as the previous burs. Caution is necessary when using
these polishers at high-speed as the silicone may degrade quickly and
can become detached from the mandrel. A feathering, light touch at
slow speed is required to reduce the build-up of heat and to avoid
premature degradation. In addition, it is important that both the
patient and practitioner routinely wear eye-protection during these
procedures. Again, an electric handpiece at 30-40,000 rpm works
well as the polisher is not “bogged down” due to the constant torque
characteristically applied by these contra-angles. After a suitable shine
is achieved, any additional final finishing can be performed using
ORTHODONTIC ADHE
polishing pastes or slurry of fine pumice as each situation dictates.
ORTHODONTIC ADHESIVE REMOVAL AND POLISHING KIT
S. Jay Bowman, DMD, MSD
ORTHODONTIC ADHESIVE REMOVAL AND POLISHING KIT
S. Jay Bowman, DMD, MSD
The resin/enamel interface
is finished with the NTI®
finishing carbide also creating
a smooth surface.
ORTHODONTIC ADHESIVE REMOVAL AND POLISHING KIT
An NTI® (H375R-016,)
S. Jay Bowman, DMD, MSD
Trimming and Finishing Carbide
is used to remove residual resin
from the enamel. H246L-012UF: After large, residual composite or cement “tags” are removed for the
shapeThe
permits
enamel surfaces, the resin/enamel interface mustThe
be pointed
polished.
NTI® Finishing
Carbide (White) is a long, flame-shaped 30-bladethis
burbur
is to
thebetype
that isatperfect
positioned
removing the remnants of adhesives and cementsthewhile
also gingival
finishing
the enamel to a
marginal
while
H375R-016: After orthodontic appliances have been removed, the NTI® 7675
smooth surface with reduced vibration.1,2 The versatile, pointed shape permits this
mammelons
polishing away adhesive
Carbide (Red) is used in either a slow or high-speedEnamoplasty
contra-angleofdental
handpiece to
bur
to
even
be positioned
just under the marginal gingival while polishing away any
H375R-016:
After
orthodontic
appliances
haveround-end,
been removed,
the
7675
dislodge
gross residual
resin
tags from the
enamel. or
This
tapered
12-blade
uneven
incisal edges
can
beNTI®
primers,
sealants
adhesive
primers, sealants, or varnishes (often used
to help
prevent enamel
burCarbide
is ideal for
removing
both
bonding
adhesives and
cements that
(Red)
is used
inorthodontic
either a slow
or high-speed
contra-angle
dental handpiece to
demineralization)
that may yet remain on the enamel.
If used without water-spray,
accomplished
during
this
step.
or
varnishes.
remain on the teeth after de-bracket and/or de-banding. The tapered design is easy
dislodge gross residual resin tags from the enamel. This round-end, tapered 12-blade
Use an NTI® Silicone point
polisher to refine the surface
at 30,000-40,000 rpm
for smooth, consistent and
comfortable polishing during
orthodontic applications.
After suitable enamel surface
is achieved, any additional
finishing can be performed
using polishing paste or fine
pumice slurry as each
situation dictates.
the residual resin is often visible as the air exhaust from the high-speed contra-angle
to manipulate
on the peripheral
enamel surfaces
and the
round-end
reduces
bur is idealaround
for removing
both orthodontic
bonding
adhesives
and
cements that
potential gingival tissue impingement. Enamoplasty of mammelons ordesiccates
uneven the surface of the tooth, making the polishing process easier.
P0153-031: Although the 30-blade finishing carbide produces
remain on the teeth after de-bracket and/or de-banding. The tapered design is easy
incisal edges can be accomplished in this same step. As an added benefit, this same
to manipulate around on the peripheral enamel surfaces and the round-end reduces
during the polishing process, the NTI® Polisher, green frictio
bur can also be employed for removing Invisalign composite attachments. Ideally,
gingival
impingement.
Enamoplasty
of mammelons
or uneven
the potential
constant torque
andtissue
low vibration
of an electric
dental contra-angle
at 35-40,000
Axis
Dental
Corporation
polisher is used to refine the final enamel surface. This flame
edges
can
be accomplished
same
step.
As
added
benefit, this
cesincisal
been
removed,
the
rpm
ishave
perfectly
suited
for
use withH246L-012UF:
this NTI®
burin
inthis
this7675
application.
Thean
intent
of composite
this
After
large,
residual
orsame
cement “tags” are removed for the
Coppell,
TX 75019
USA
bur can
be any
employed
removing
Invisalign
composite
attachments.
Ideally,
process
is to also
remove
residualfor
adhesives
and
cements
but
not
to
unintentionally
polisher can also be used in the same low or high-speed denta
enamel
surfaces,
the resin/enamel
interface must be polished. The NTI® Finishing
rdisturb
high-speed
contra-angle
dental
handpiece
to hand, specific
Free:
800.355.5063
enamelToll
anatomy
or
over-polish
the surface.
the other
sites at 35-40,000
the constant
torque
and
lowCarbide
vibration
of anOn
electric
dental
contra-angle
(White)
is a long,
flame-shaped
30-blade bur is the type that is perfect
previous burs. Caution is necessary when using these polishe
he
enamel.
This
round-end,
tapered
12-blade
www.axisdental.com
of uneven
pitted,
or
blemished
enamel
can
be
refined
at
this
stage.
rpm is perfectly suited for use with this bur in this application. The intent of this
P0153-031: Although the 30-blade finishing carbide produces a smooth surface
during the polishing process, the NTI® Polisher, green friction-grip FG silicone
polisher is used to refine the final enamel surface. This flame or conical shaped
polisher can also be used in the same low or high-speed dental handpiece as the
removing the remnants of adhesives and cements while also finishing the enamel to a
silicone
will Axis
degrade
quickly and can become
ticprocess
bonding
cements
that
All trademarks
are not
the property
of, or licensed to, Axis Dental Corporation, unless otherwise
noted. ©2010
Dental Corporation.
LS-7585-TS detached from
is to adhesives
remove any and
residual
adhesives
and
cements but
to 1,2
unintentionally
previous
Caution
is necessary
smooth surface with reduced vibration.
Theburs.
versatile,
pointed shape
permits this when using these polishers in high-speed as the
disturb
enamel anatomy
or over-polish
the surface.
On the other hand, specific sites
d/or
de-banding.
The tapered
design
is
easy
feathering,
light
touch
at
slow
revolutions
is required to reduc
bur to even be positioned just under the marginal gingival while polishing away any