Download Current Transducer HAT 200..1500

Current Transducer HAT 200..1500-S
For the electronic measurement of currents: DC, AC, pulsed, mixed,
with a galvanic isolation between the primary circuit (high power) and
the secondary circuit (electronic circuit).
IPN = 200..1500 A
VOUT = ± 4 V
Electrical data
Primary nominal
current rms
IPN (A)
Primary current
measuring range 4)
IPM (A)
200
400
500
600
800
1000
1200
1500
VC
IC
R IS
VOUT
ROUT
RL
±
±
±
±
±
±
±
±
600
1200
1500
1800
2400
2500
2500
2500
Type
HAT
HAT
HAT
HAT
HAT
HAT
HAT
HAT
200-S
400-S
500-S
600-S
800-S
1000-S
1200-S
1500-S
Supply voltage (± 5 %) 4)
Current consumption
Isolation resistance @ 500 VDC
Output voltage (Analog) @ ± IPN, RL = 10 kΩ, TA = 25°C
Output internal resistance
Load resistance
RoHS since
date code
• Hall effect measuring principle
• Galvanic isolation between primary
47143
46115
46129
46115
46115
46097
planned
46158
± 15
± 15
> 1000
±4
100
> 10
•
•
•
•
V
mA
MΩ
V
Ω
kΩ
ε
L
VOE
VOH
TCVOE
TCVOUT
tr
BW
m
Notes :
Advantages
• Easy installation
• Small size and space saving
• Only one design for wide current
ratings range
Accuracy @ IPN, TA = 25°C (excluding offset)
Linearity error 1) (0 .. ± IPN)
Electrical offset voltage @ TA = 25°C
Hysteresis offset voltage @ IP = 0;
after an excursion of 1 x IPN
Temperature coefficient of VOE
Temperature coefficient of VOUT(% of reading)
Response time to 90% of IPN step
Frequency bandwidth 2) (- 3 dB)
< ± 1 % of IPN
< ± 1 % of IPN
< ± 20
mV
< ± 10
mV
<±1
mV/K
< ± 0.1
%/K
<5
µs
DC .. 25
kHz
Ambient operating temperature
- 10 .. + 80
Ambient storage temperature HAT 200-S, HAT 500..1500-S - 15 .. + 85
HAT 400-S
- 25 .. + 85
Mass
300
interference.
Applications
• DC motor drives
• Switched Mode Power Supplies
(SMPS)
• AC variable speed drives
• Uninterruptible Power Supplies
(UPS)
• Battery supplied applications
• Power supplies for welding
General data
TA
TS
and secondary circuit
Isolation voltage 3000 V
Low power consumption
Extended measuring range(3 x IPN)
Isolated plastic case recognized
according to UL 94-V0
• High immunity to external
Accuracy-Dynamic performance data
X
Features
°C
°C
°C
g
applications
Application domain
• Industrial
Linearity data exclude the electrical offset.
Please refer to derating curves in the technical file to avoid excessive
core heating at high frequency.
3)
Please consult characterisation report for more technical details and
application advice.
4)
Operating at ±12V ≤ Vc < ±15V will reduce the measuring range.
1)
2)
Page 1/3
080307/13
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice.
www.lem.com
Current Transducer HAT 200..1500-S
Isolation characteristics
Vb
Vd
dCp
dCl
CTI
Rated isolation voltage rms
with IEC 61010-1 standards and following conditions
- Reinforced insulation
- Over voltage category III
- Pollution degree 2
- Heterogeneous field
Rms voltage for AC isolation test, 50 Hz, 1 min
Creepage distance
Clearance distance
Comparative Tracking Index (Group IIIa)
1000
3
> 11
> 11
275
V
kV
mm
mm
Page 2/3
080307/13
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice.
www.lem.com
Dimensions HAT 200..1500-S (in mm. 1 mm = 0.0394 inch)
70
37
10
24
30
20
20
4 1
65
30.50
40.50
3
4
90
12
Current Direction
6
1
78
4.50
5
4.
0
6
12
Safety
Mechanical characteristics
• General tolerance
• Transducer fastening
• Connection of secondary
Pins Arrangement
1
2
3
4
+
- OUT GND
± 1 mm
By base-plate or on
bus bar with M4
screws.
All slots ∅ 4.5 mm
Molex 5045-04A
This transducer must be used in electric/electronic equipment
with respect to applicable standards and safety requirements
in accordance with the following manufacturer's operating
instructions.
Caution! Risk of electrical shock
Remarks
• IS is positive when IP flows in the direction of the arrow.
• Temperature of the primary conductor should not exceed
100°C.
When operating the transducer, certain parts of the module can
carry hazardous voltage (eg. primary busbar, power supply).
Ignoring this warning can lead to injury and/or cause serious
damage.
This transducer is a built-in device, whose conducting parts
must be inaccessible after installation.
A protective housing or additional shield could be used.
Main supply must be able to be disconnected.
Page 3/3
080307/13
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice.
www.lem.com