Download LDO PSRR Measurement Simplified

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Time-to-digital converter wikipedia , lookup

Variable-frequency drive wikipedia , lookup

Alternating current wikipedia , lookup

Chirp spectrum wikipedia , lookup

Mains electricity wikipedia , lookup

Tube sound wikipedia , lookup

Pulse-width modulation wikipedia , lookup

Negative feedback wikipedia , lookup

Audio power wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Signal-flow graph wikipedia , lookup

Analog-to-digital converter wikipedia , lookup

Islanding wikipedia , lookup

Rectifier wikipedia , lookup

Schmitt trigger wikipedia , lookup

Power electronics wikipedia , lookup

Two-port network wikipedia , lookup

Oscilloscope wikipedia , lookup

Amplifier wikipedia , lookup

Buck converter wikipedia , lookup

Oscilloscope types wikipedia , lookup

Metadyne wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Heterodyne wikipedia , lookup

Opto-isolator wikipedia , lookup

Transcript
Application Report
SLAA414 – July 2009
LDO PSRR Measurement Simplified
Sanjay Pithadia and Scot Lester .................................................................... PMP - LP Linear Regulators
ABSTRACT
This application report explains different methods of measuring the Power Supply
Rejection Ratio (PSRR) of a Low-Dropout (LDO) regulator and includes the pros and
cons of these measuring methods.
What is PSRR?
Power Supply Rejection Ratio or Power Supply Ripple Rejection (PSRR) is a measure of a circuit’s power
supply’s rejection expressed as a log ratio of output noise to input noise. PSRR provides a measure of
how well a circuit rejects ripple, of various frequencies, injected at its input. The ripple can be either from
the input supply such as a 50Hz/60Hz supply ripple, switching ripple from a DC/DC converter, or ripple
due to the sharing of an input supply between different circuit blocks on the board. In the case of LDOs,
PSRR is a measure of the regulated output voltage ripple compared to the input voltage ripple over a wide
frequency range (10Hz to 1MHz is common) and is expressed in decibels (dB). The PSRR is very critical
parameter in many audio and RF applications.
The basic equation for PSRR is:
Ripple Input
PSRR = 20 log
Ripple Output
(1)
Historically LDOs have poor high frequency PSRR performance, but currently TI has LDOs with PSRR >
40dB at 5MHz. One important point regarding the PSRR graphs in TI LDO datasheet is that the PSRR
axis is inverted (See Figure 1). The PSRR is calculated as rejection so it should be a negative number;
however, the graph shows it as positive number so that a higher number denotes higher noise rejection.
80
150 mA
70
PSRR - dB
60
10 mA
50
40
75 mA
30
20
COUT = 1 mF,
CNR = 10 nF
10
0
10
100
1k
10 k
100 k
f - Frequency - Hz
1M
10 M
Figure 1. PSRR Graph of TPS717xx LDOs
SLAA414 – July 2009
Submit Documentation Feedback
LDO PSRR Measurement Simplified
1
Measuring PSRR of LDO
www.ti.com
Measuring PSRR of LDO
The following sections explain different methods of measuring the PSRR of an LDO.
1. Measuring PSRR using LC summing node method:
The basic method of measuring PSRR is shown in Figure 2. In this method, DC voltage and AC
voltages are summed together and applied at the input of the LDO. VDC is the operating point bias
voltage and VAC is the noise source used in the test. Capacitor C prevents VAC from shoring VDC
and inductor L prevents VDC from shorting VAC. So L and C are used for isolating both the sources,
VDC and VAC, from each other.
The L and C will create a high pass filter for VAC which will limit how low in frequency we can measure
the PSRR. The 3dB point of this filter is determined by Equation 2. Frequencies below the 3dB point
will start to be attenuated which will make measurements more difficult. The highest frequency that can
be measured is determined by the self resonant frequencies of the L and C components.
Fmin = 1/ 2Π √LC
(2)
A drawback to this method is that it works well only for mid-range frequencies (approximately 1 kHz to
500 kHz).
VIN
VOUT
LDO
VIN
CIN
C
GND
COUT
LOAD
+
+
L
VOUT
VDC
VAC
Figure 2. Basic Method of Measuring PSRR of LDO
2. Measuring PSRR using summing amplifier
To improve the measurement of PSRR, a recommended method is described using a high-bandwidth
amplifier as summing node to inject the signals and provides the isolation between VAC and VDC. This
method is tested and verified using TPS72715 LDO and THS3120 high-speed amplifier from Texas
Instruments. The basic set-up is shown in Figure 3. The PSRR is measured with a no-load condition
and the resulting measured PSRR graph corresponds with the datasheet graph of PSRR.
Keep in mind the following while measuring the PSRR using this method:
a. The input capacitor of LDO should be removed before the measurement because this capacitor
could cause the high-speed amplifier to go unstable.
b. Vin and Vout should be measured with high-impedance probes (either scope or network analyzer)
immediately at the Vin or Vout pins to minimize the set-up inductance effects.
c. There test set-up should not have any long wires since this will add inductance and impact the
results.
d. While selecting the values of AC and DC inputs, the following conditions should be considered:
VAC (max) + VDC < VABS (max) of LDO
VDC – VAC > VUVLO of LDO
Also, the best results will be obtained if:
VDC–VAC>Vout + Vdo + 0.5 where Vout is the output voltage of the LDO and Vdo is the
specified drop out voltage at the operating point.
e. At very high frequencies, the response of the amplifier will start to attenuate the VAC signal that is
applied to the LDO. At some point, the attenuated VAC will be too small to measure on the output
of the LDO.
f. As load current increases, the open-loop output impedance of LDO decreases (Since a MOSFET
output impedance is inversely proportional to the drain current), thus lowering the gain. Increasing
the load current also pushes the output pole to higher frequencies, which increases the feedback
2
LDO PSRR Measurement Simplified
SLAA414 – July 2009
Submit Documentation Feedback
Measuring PSRR Using Oscilloscope
www.ti.com
loop bandwidth. The net effect of increasing the load is therefore reduced PSRR at lower
frequencies (because of reduced gain) along with increased PSRR at higher frequencies.
High Impedance Adapters (Model # 41802A from Agilent)
CH2
CH1
1 kW
100 mF
RF out
+10 V
1 kW
-
DC out
FB*
THS3120
100 W
DUT
COUT
+
-10 V
Network
Analyzer
(Model #
4395A from
Agilent)
Built on THS3120 EVM
FB* à Ferrite Bead having impedance of
10 W @ 100 MHz
Figure 3. Recommended Method of Measuring PSRR of LDO
Figure 4 shows the PSRR graph measured with this method.
Figure 4. PSRR Measured With Recommended Method
The THS3120 is suitable for measuring PSRR up to VDC = 5V, Frequency = 10MHz and Iload =
400mA.
Measuring PSRR Using Oscilloscope
If the user does not have a network analyzer then there is a simpler but more cumbersome method which
uses a signal generator, DC source and oscilloscope to measure the PSRR. An AC signal from signal
generator is applied along with DC signal at the input of the LDO, as shown in either of the afore
mentioned methods, and the output of the LDO is measured on an oscilloscope at different VAC
frequencies. The PSRR is calculated using the Equation 1 where Ripple(input) is the amplitude of the input
AC signal and Ripple(output) is the amplitude of output signal. This is then repeated at different frequencies
of VAC to generate a piecemeal graph of PSRR.
This method can be used along with the set-ups described in the previous section. But this method is only
good for LDOs with lower PSRR values due to resolution and sensitivity of oscilloscopes. Since most
oscilloscopes can measure down to the millivolt range, the maximum range of PSRR that could
realistically be measured using an oscilloscope is about 40dB–50dB.
SLAA414 – July 2009
Submit Documentation Feedback
LDO PSRR Measurement Simplified
3
Measuring PSRR Using Oscilloscope
www.ti.com
Using the TPS78101EVM from Texas Instruments, the PSRR is measured using signal generator and
oscilloscope. The input and output waveforms are as shown in Figure 5:
Test conditions are:
a. Vout = 3V
b. Iload = 150mA
c. VAC = 1V (p-p) at 1kHz
d. VDC = 4.3V dc
Figure 5. Input and Output Waveforms for Measuring PSRR Using Oscilloscope
And the PSRR is calculated from waveforms in Figure 5 is:
Ripple(input) = 984 mV
Ripple(output) = 194 mV
PSRR = 20 log10(Ripple(input)/ Ripple(output)) = 20 log10(0.984/0.194) = 14.10dB which closely matches the
PSRR specified in the datasheet of TPS78101.
This application report shows various methods to measure the PSRR of an LDO and also explains
different aspects which need to be considered while measuring PSRR.
4
LDO PSRR Measurement Simplified
SLAA414 – July 2009
Submit Documentation Feedback
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated