Download E¡E¡E¡E¡E - distrelec.biz

40W Multiple-Stage Output Current LED Power Supply
E¡¡E¡½
¡E¡E
¡E¡E
¡E¡E
¡E¡E
¡E¡E
¡E¡E
E¡
LCM-40DA
series
Features :
Output current level selectable by DIP S.W.
180~295VAC input only
Built-in active PFC function
Protections: Short circuit / Over voltage / Over temperature
Cooling by free air convection
Fully isolated plastic case
Class
power unit, no FG
Built-in DALI interface and push dimming function
Built-in 12V/50mA auxiliary output
IP20 design
Temperature compensation function by external NTC
No load power consumption <1.2W(Note.7)
Power supplies synchronization function up to 10 units
Suitable for indoor LED lighting applications
3 years warranty
110
F
¢º
M
M
SELV
SPECIFICATION
MODEL
LCM-40DA
SELECTABLE CURRENT Note.3 350mA
DC VOLTAGE RANGE
2 ~ 100V
RATED POWER
42W
5%
600mA
700mA
900mA
1050mA
2 ~ 67V
2 ~ 57V
2 ~ 45V
2 ~ 40V
¡Ó
RIPPLE CURRENT
OUTPUT
500mA
2 ~ 80V
RIPPLE & NOISE (max.) Note.2 700mVp-p
NO LOAD OUTPUT VOLTAGE (max.) 110V
Note.5 1000ms, 80ms / 230VAC at rated power
SETUP, RISE TIME
16ms/230VAC at rated power
HOLD UP TIME (Typ.)
VOLTAGE RANGE
Note.4 180 ~ 295VAC
¡Ù
POWER FACTOR (Typ.)
PROTECTION
¡Ù
PF 0.975/230VAC, PF 0.96/277VAC at rated power (Please refer to "Power Factor Characteristic" curve)
TOTAL HARMONIC DISTORTION Total harmonic distortion will be lower than 20% when output loading is 75% or higher
EFFICIENCY (Typ.)
Note.6 91%
AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
0.23A/230VAC
0.2A/277VAC
COLD START 20A(twidth=260 s measured at 50% Ipeak) at 230VAC
LEAKAGE CURRENT
<0.5mA / 240VAC
SHORT CIRCUIT
Constant current limiting, recovers automatically after fault condition is removed
110 ~ 130V
Protection type : Shutdown o/p voltage, re-power on to recover
OVER VOLTAGE
OVER TEMPERATURE
£g
¢J ¡Ó10¢J (RTH2)
90
Protection type : Shut down o/p voltage, re-power on to recover
¡Ó
TEMP. COMPENSATION
12V @ 50mA for driving fan; Tolerance 5%
By external NTC(not provide with the power supply), please see "Temperature compensation operation"
DIMMING
Please see "Dimming Operation"
SYNCHRONIZATION
Please see "Synchronization Operation"
AUXILIARY POWER
FUNCTION
254 ~ 417VDC
47 ~ 63Hz
FREQUENCY RANGE
INPUT
65V
¡Ó5.0%
CURRENT ACCURACY
WORKING TEMP.
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
¢J (Refer to "Derating Curve")
-30 ~ +60
20 ~ 90% RH non-condensing
¢J
¡Ó0.03%/¢J (0 ~ 50¢J)
-40 ~ +80 , 10 ~ 95% RH
VIBRATION
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY STANDARDS
UL8750, ENEC EN61347-1, EN61347-2-13,EN62384 independent approved
DALI STANDARDS
Comply with IEC62386-101, 102, 207
SAFETY & WITHSTAND VOLTAGE
I/P-O/P:3.75KVAC
EMC
I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH
Compliance to EN55015, EN61000-3-2 Class C( 40% rated power) ; EN61000-3-3
ISOLATION RESISTANCE
EMC EMISSION
EMC IMMUNITY
MTBF
OTHERS
DIMENSION
PACKING
NOTE
¢J
¡Ù
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61547 light industry level (surge 2KV), criteria A
193.6K hrs min. MIL-HDBK-217F (25 )
¢J
123.5*81.5*23mm (L*W*H)
0.24Kg ; 54pcs/15Kg/1.12CUFT
¢J
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf parallel capacitor.
3. Please see "DIP switch table".
4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
5. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
6. Efficiency is measured at 500mA/80V output set by DIP switch.
7. No load power consumption<1.2W is measured at 180~277VAC, with lighting fixture connected and output current dimmed to 0%.
8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
File Name:LCM-40DA-SPEC 2013-02-01
LCM-40DA
40W Multiple-Stage Output Current LED Power Supply
Mechanical Specification
Case No.LCM-60A
series
Unit:mm
123.5
6.75
6.75
6.75
110
1
2
£r4.
2
6.75
3
268
81.5
TB1
4
5
1
2
3
4
T case 25
SYN.
20
TB3
1
CN101
2
3
CN100
4
1
2
TB5
ON
1 2 3 4 5 6
¡° T case: Max. Case Temperature.
39.3
Terminal Pin No. Assignment(TB3)
65.5
Pin No.
1
2
7.8
2-M3
Assignment
+FAN
-FAN
Pin No.
3
4
Assignment
+NTC
-NTC
4
7.8
Terminal Pin No. Assignment(TB5)
23
Pin No.
1
2
SYN. Connector(CN101/CN100):JST B2B-XH or equivalent
Terminal Pin No. Assignment(TB1)
Pin No.
1
2
3
Assignment
AC/L
AC/N
PUSH
Pin No.
4
5
Assignment
+Vo
-Vo
Pin No.
1,3
2,4
Assignment
DA+
DA-
Assignment
+
-
Mating Housing
Terminal
JST XHP
or equivalent
JST SXH-001T-P0.6
or equivalent
PFC fosc : 60KHz
PWM fosc : 80KHz
Block Diagram
EMI FILTER
&
RECTIFIERS
I/P
POWER
SWITCHING
PFC
CIRCUIT
RECTIFIERS
+12Vaux
RECTIFIERS
&
FILTER
+V
-V
DIM+
DIM-
O.L.P.
O.L.P.
PFC
CONTROL
DETECTION
CIRCUIT
PWM
CONTROL
O.T.P.
MCU
O.V.P.
Derating Curve
Static Characteristics
100
100
Others
90
80
80
70
40
LOAD (%)
LOAD (%)
60
1050mA
20
-30
-15
0
15
30
40 45 50
¢J
AMBIENT TEMPERATURE ( )
60
70
(HORIZONTAL)
60
50
40
180
190
200
210
220
230 240
250
260
270
280
295
INPUT VOLTAGE (V) 60Hz
File Name:LCM-40DA-SPEC 2013-02-01
40W Multiple-Stage Output Current LED Power Supply
LCM-40DA
series
DIP Switch Table
LCM-40DA is a multiple-stage output current supply, selection of output current through DIP switch as table below.
DIP S.W.
1
2
3
4
5
6
350mA
----
----
----
----
----
----
500mA
ON
----
----
----
----
----
600mA
ON
ON
----
----
----
----
700mA(Factory Setting) ON
ON
ON
----
----
ON
900mA
ON
ON
ON
ON
----
ON
1050mA
ON
ON
ON
ON
ON
ON
Io
Power Factor Characteristic
Constant Current Mode
Constant Current Mode
1.00
0.97
0.91
350
0.88
500
0.85
600
0.82
700
0.79
900
0.76
1050
PF
PF
0.94
0.73
0.70
0.98
0.95
0.92
0.89
0.86
0.83
0.80
0.77
0.74
0.71
0.68
0.65
0.62
0.59
0.56
0.53
0.50
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
350
500
600
700
900
1050
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
(40W)
(40W)
LOAD
(230Vac Input)
LOAD
(277Vac Input)
EFFICIENCY vs LOAD
95.0%
95.0%
90.0%
90.0%
85.0%
85.0%
80.0%
350
75.0%
500
70.0%
600
65.0%
700
60.0%
900
55.0%
1050
50.0%
EFFICIENCY (%)
EFFICIENCY (%)
LCM-40DA series possess superior working efficiency that up to 91% can be reached in field applications.
80.0%
350
75.0%
500
70.0%
600
65.0%
700
60.0%
900
55.0%
1050
50.0%
45.0%
45.0%
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD
(230Vac Input)
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD
(277Vac Input)
File Name:LCM-40DA-SPEC 2013-02-01
40W Multiple-Stage Output Current LED Power Supply
LCM-40DA
series
DIMMING OPERATION
¡° PUSH dim(primary side)
Ignore
To avoid reaction on AC spike
<0.05 sec.
Short push
Push to turn ON-OFF
0.1~1 sec.
Long push
Dimming up or down
1.5~10 sec.
Reset push
Setting light to 100%
>11 sec.
LCM-40DA
DADA+
PUSH
AC/N
AC/L
¡EMaximum number of drivers up to 10 pcs.
¡EMaximum length of the cable, from push button to last driver is 20 meter.
¡EFactory setting at 100%.
E¡ When the light is lower than 10% it will always dim up, or when the light output is higher than 90% it will always dim down.
Push Button
AC/N
AC/L
Warning: The pushbutton can only be connected in between the PUSH terminal of LCM-40DA and AC/L (brown or black color). It would cause short
circuit if it is connected to AC/N.
¡° DALI interface(primary side)
E¡ DALI protocol including 16 groups and 64 addresses.
E¡ First step is fixed at 6% light output.
SYNCHRONIZATION OPERATION
¡E10 drivers(max.) synchronization (1 master + 9 slaves)
E¡ Maximum cable length between each units : 20 meter.
20m
SYN.
- -
LCM-40DA
(Slave 1)
SYN.
- -
+
+
LCM-40DA
(Master)
+
+
SYN.
- -
+
+
LCM-40DA
(Slave 2)
20m
File Name:LCM-40DA-SPEC 2013-02-01
40W Multiple-Stage Output Current LED Power Supply
LCM-40DA
series
TEMPERATURE COMPENSATION OPERATION
NTC derating curve
105
100
£[
£
[
470KO
470K
£[
220KO
220K
95
Output Io (%)
330KO
330K
90
85
80
75
70
65
55
60
65
70
75
80
85
90
95
Sensed Temperature(degree)
¡ô ¡õ
LCM-40DA have the built-in temperature compensation function (T ,Io ) . By connecting a temperature sensor (NTC resistor) between the NTC +/terminal of LCM-40DA and the detecting point on the lighting system or the surrounding environment, output current of LCM-40DA could be
correspondingly changed to ensure the long life of LED.
1.LCM-40DA can still be operated well when the NTC resistor is not connected and the value of output current will be the current level that you set
through the DIP switch.
2.
NTC resistance
220K
330K
470K
Output Current
¢J
J¢
< 70¢J, 100% of the rated current (corresponds to the setting current level)
> 70¢J, output current begin to reduce, details please refer to the curve.
< 80¢J, 100% of the rated current (corresponds to the setting current level)
> 80¢J, output current begin to reduce, details please refer to the curve.
< 60 , 100% of the rated current (corresponds to the setting current level)
> 60 , output current begin to reduce, details please refer to the curve.
Notes: 1. MW does not offer the NTC resistor and all the data above are measured by using THINKING TTC03 series.
2. If other brands of NTC resistor is applied,please check the temperature curve first.
3. Synchronization function of the power supply will be invalid when the "temperature compensation" function is in use.
File Name:LCM-40DA-SPEC 2013-02-01