Download Deriving Relationships from Graphs

Deriving Relationships from Graphs
Graphing is a powerful tool for representing and interpreting numerical data. In addition, graphs and
knowledge of algebra can be used to find the relationship between variables plotted on a scatter chart.
Consider the following examples and procedures. Become familiar with these approaches, and attempt to
thoroughly understand the processes illustrated here. You will be using these approaches regularly in
introductory physics laboratory activities. Please note that this is merely an introduction to deriving
relationships from graphs. There ultimately will be much more to learn.
Linear Relationships:
The graph to the left depicts a linear relationship. That is,
the data points all can be connected with a straight line.
Note that the best-fit line does not pass through the origin;
rather, it passes through the y-axis at -1m. How would one
define the relationship between the values of the x and y
coordinates in this relationship? It’s done with the equation
of a straight line, y = mx + b where m is the slope and b is
the value of the y-intercept – the value of y when x = 0. The
slope, m, is found from Δy/Δx = (y2 - y1)/(x2 - x1) = 2m/s in
this graph. The value of b can be found from inspection as
equal to -1m. The algebraic relationship is then represented
as y = mx + b where y is identified with the distance, x is
identified with time, m the slope, and b the y-intercept.
Thus, our relationship from the graph is:
distance = (2m/s)time – 1m.
Proportional Relationships:
The graph to the left approximates the proportional
relationship between voltage and current in a circuit. Note
that a relationship is directly proportional only when the
relationship is linear and passes through the origin. This is
not quite the case in the current graph. The value of b is
0.0180 amps. The linear fit derived by the computer used to
generate the graph performs an algebraic best fit to the data.
The equation generated is the best mathematical fit, but the
fit does not properly represent the physical reality of the
situation. If no voltage is applied, then no current flows. If
this is the case, the best-fit line must pass through the origin
in what is known as a physical fit of the data. A physical fit
demands y = Ax as the model for the fit. Under the new
analysis m = 2amps/volt. Then we find:
current = (2amps/volt)voltage
(continued)
Non-linear Relationships:
The graph to the left is a hyperbolic relationship. That is, the data
are not linear and both sets of values appear to approach
asymptotes. There are two approaches that one might use to find
the relationship between the variables pressure and volume. One
can perform a non-linear regression analysis to find the
relationship using a calculator or computer, or linearize the plot by
manipulating the data and re-plotting in an effort to create a linear
relationship between the manipulated variables. Looking at the
data carefully suggests that we have here an inverse relationship.
That is, when pressure is doubled, the volume is halved. The
relationship between the variables would seem to be of the form
pressure is inversely proportional to volume. Assuming for a
moment that this is the case, data for either pressure or volume can
be inverted (e.g., replace by 1/var) and the data re-graphed to see if
a linear relationship results. Replacing volume by 1/volume results in the graph below.
Linearized Plot of Above Data:
Here we see a linearized plot of the pressure-volume data used to
create the graph above. On the horizontal axis of the graph the
inverse of the volume has been plotted; pressure is plotted as
before on the vertical axis. A linear fit of the type y = mx + b is
now possible and shows that a linear relationship exists between
pressure and the inverse of the volume in this particular situation.
Note that the x-variable is identified with 1/volume, that the yvariable is identified with 1/volume, and that b = 0. That is,
pressure = (3atm*lit)/volume
or
pressure * volume = 3atm*lit
The “Simpler, More Natural” Fit:
Students are sometimes tempted to use a polynomial function to
conduct a non-linear curve fit using calculators or computers (e.g.,
y = a + bx + cx2 + dx3 + ex4 + fx5 +…). Such a function will fit
almost any data so long as the degree of the function is high
enough. What sometimes happens though (as did not happen in the
graph to the left) is that there will be wild migrations of the best-fit
curve between the data points that probably wouldn’t happen in
nature. Fortunately, Mother Nature is less complex than that, and
best fits involving trigonometric functions and the like can provide
simpler forms of relationship. Note the 4th order power function fit
of the graph to the left. A trigonometric function given by intensity
= (2.5lux)cos(θ) is a “simpler” representation of the data and a
“more natural” fit with the data. As a rule, simpler interpretations
are valued over more complex in science.